Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2011.08–2016.09
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248170 AUTOMATIC TRANSAXLE SYSTEM C

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2769  Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  P2770  Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  


DESCRIPTION

Shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hydraulic pressure in the lock-up relay valve, which then controls the operation of the lock-up clutch.

Fail-safe function:

·

If the ECM detects a malfunction, it turns shift solenoid valve SL OFF.


·

The system cannot control the lock-up relay valve. (No relation to 3-4 shift control)


DTC No. DTC Detection Condition Trouble Area
P2769 ECM detects short in solenoid valve SL circuit when solenoid valve SL operated. (Solenoid resistance: 8 Ω or less)
(2-trip detection logic)
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve SL

·

ECM


P2770 ECM detects open in solenoid valve SL circuit when solenoid valve SL not operated. (Solenoid resistance: 100 kΩ or more)
(2-trip detection logic)
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve SL

·

ECM



MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the mass airflow meter and the crankshaft position sensor, the ECM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smoother gearshifting. Shift solenoid valve SL responds to the signals from the ECM. The valve controls the lock-up relay valve to perform the torque converter lock-up function. If the ECM detects an open or short circuit of shift solenoid valve SL, it illuminates the MIL and sets a DTC.

WIRING DIAGRAM

C243326E04
0.98,1.96 1.280,2.099 0.300,0.140 10 B74 0.98,2.118 2.167,2.296 1.186,0.178 10 Transmission Wire 6.025,2.177 6.375,2.342 0.350,0.165 10 ECM 5.838,1.092 6.040,1.253 0.202,0.161 10 SL 5.468,1.09 5.753,1.255 0.286,0.165 10 B84 5.523,0.9 5.698,1.054 0.175,0.154 10 57 2.298,1.215 2.499,1.374 0.201,0.159 10 SL 2.616,0.992 2.713,1.148 0.097,0.156 10 4 1.149,1.329 2.042,1.639 0.894,0.310 10 Shift Solenoid Valve SL

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C229166E17
1.012,1.782 1.233,1.943 0.221,0.161 10 SL 1.413,1.015 1.148,1.745 false 0.059,0.028 0.256,0.192 0.197,0.164 10 *a

Disconnect the transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SL) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
U158338E01
1.482,0.254 1.785,0.421 0.303,0.167 10 B84 0.048,0.027 0.258,0.210 0.210,0.182 10 *a 1.829,1.798 2.049,1.948 0.220,0.150 10 SL 1.463,0.998 1.938,1.77 false

Connect the transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-57 (SL) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR