Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248179 AUTOMATIC TRANSAXLE UNIT G

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 34633 1.INSPECT 2ND COAST AND OVERDRIVE BRAKE DISC

C203928

a.

Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35682 2.INSPECT 2ND BRAKE BRAKE DISC

C203929

a.

Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the groove is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35683 3.INSPECT 1ST AND REVERSE BRAKE DISC

C203930

a.

Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35667A 4.INSPECT DIRECT CLUTCH DISC

C059971

a.

Check whether the sliding surfaces of the disc, plate and flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed number is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35608L 5.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C060707

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.85 mm (0.6240 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 35068 6.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C060848

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.71 mm (0.85472 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 35604 7.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C059943

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

36 mm (1.42 in.)


If the free length is shorter than the standard free length, replace the direct clutch return spring sub-assembly.


Hide 35603A 8.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C060024

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

24.04 mm (0.9465 in.)


If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly.


Hide 34603B 9.INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

C059838

a.

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

18.99 mm (0.748 in.)


If the free length is shorter than the standard free length, replace the overdrive brake return spring sub-assembly.


Hide 35606A 10.INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C059942

Make sure that the check ball moves freely by shaking the piston.


b.

Check that the valve does not leak by covering the check hole with a finger and applying low pressure compressed air as shown in the illustration.

If necessary, replace the direct clutch piston sub-assembly


Hide 35102 11.INSPECT REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C059818

Using a dial indicator, measure the inside diameter of the rear cover bush.

Standard inside diameter:

13.94 to 13.96 mm (0.549 to 0.550 in.)


If necessary, replace the rear transaxle cover sub-assembly.