Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248179 AUTOMATIC TRANSAXLE UNIT A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572A 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER

C107764

a.

Remove the nut, washer and transmission control shaft lever.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C057495

a.

Using a screwdriver, pry out the lock plate and remove the nut, lock plate and washer.


b.
C107763

Remove the 2 bolts and pull out the park/neutral position switch assembly.


Hide 89413B 3.REMOVE TRANSMISSION REVOLUTION SENSOR

U158259

a.

Remove the bolt and the transmission revolution sensor.


b.
C117099E03
1.865,1.875 2.115,1.875 false 2.188,1.792 2.385,1.99 0.198,0.198 10 false *1

Remove the O-ring from the transmission revolution sensor.

Text in Illustration
*1 O-ring


Hide 35104V 4.REMOVE BREATHER PLUG HOSE

U158263

a.

Remove the clamp and the breather plug hose.


Hide 32921C 5.REMOVE OIL COOLER TUBE UNION

U158264

a.

Remove the 2 oil cooler tube unions.


b.

Remove the 2 O-rings from the oil cooler tube unions.


Hide 30500 6.FIX AUTOMATIC TRANSAXLE ASSEMBLY

a.
C244602E02
0.948,1.771 0.625,1.594 false 2.604,1.76 2.896,1.677 false 0.406,1.49 0.615,1.656 0.208,0.167 10 false *1 2.927,1.594 3.135,1.76 0.208,0.167 10 false *1

Place the transaxle on wooden blocks.

Text in Illustration
*1 Wooden Block


Hide 35106D 7.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

C203891

a.

Remove the 18 bolts, the automatic transaxle oil pan sub-assembly and the oil pan gasket.

NOTICE:

Some fluid will remain in the oil pan. Remove all the oil pan bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



b.
U158258

Remove the 2 oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


c.

Examine the particles in the pan.

i.

Collect any steel chips using the removed magnets.

Carefully inspect the foreign matter and particles in the pan and on the magnets to guess at the type of wear which might be found in the transaxle.

Steel (magnetic): bearing, gear and clutch plate wear

Brass (non-magnetic): bearing wear




Hide 35330 8.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C203892

a.

Remove the 3 bolts and the valve body oil strainer assembly.


b.
C057509

Remove the oil strainer gasket from the valve body oil strainer assembly.


Hide 82125J 9.SEPARATE TRANSMISSION WIRE

a.
C203893

Disconnect the 5 connectors from the transmission valve body assembly.


b.

Separate the clamp and the transmission wire.


Hide 35410 10.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C203894

Remove the 14 bolts and the transmission valve body assembly.

NOTICE:

Store the bolts so that they can be reinstalled in their original positions because they are of varying lengths.



b.
U158257

Disconnect the manual valve control rod from the manual valve lever, then remove the transmission valve body assembly.


Hide 82125J 11.REMOVE TRANSMISSION WIRE

a.
C203904

Remove the bolt.


b.
C203903

Remove the transmission wire from the transaxle case.


c.
C067760

Remove the O-ring from the transmission wire.


Hide 35148 12.REMOVE NO. 1 GOVERNOR APPLY GASKET

C059784

a.

Using a screwdriver, remove the No. 1 governor apply gasket from the transaxle case.


Hide 35251 13.REMOVE CHECK BALL BODY

C059785

a.

Remove the check ball body and the compression spring.


Hide 35425A 14.REMOVE C-2 ACCUMULATOR PISTON

C203853

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out.

When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35209 15.REMOVE C-2 ACCUMULATOR SPRING SUB-ASSEMBLY

C059787

a.

Using a screwdriver, remove the snap ring and the C-2 accumulator spring sub-assembly.


Hide 35424C 16.REMOVE C-1 ACCUMULATOR PISTON

C203854

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-1 accumulator piston and the C-1 accumulator compression spring.

NOTICE:
·

Blowing off the air may cause the piston to jump out.

When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35206 17.REMOVE C-1 ACCUMULATOR SPRING SUB-ASSEMBLY

C059790

a.

Using a screwdriver, remove the C-1 accumulator spring.


Hide 35427R 18.REMOVE B-1 ACCUMULATOR PISTON

C203855

a.

Remove No. 2 B-1 accumulator compression spring.


b.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-1 accumulator piston.

NOTICE:
·

Blowing the air may cause the piston to jump out.

When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35427P 19.REMOVE B-1 ACCUMULATOR PISTON COMPRESSION SPRING

C059791

a.

Using a screwdriver, remove the B-1 accumulator piston compression spring.


Hide 35111C 20.REMOVE TRANSAXLE HOUSING

C203856

a.

Remove the 16 bolts.


b.

Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

NOTICE:

The differential gear assembly may be accidentally removed when the transaxle housing is removed.



Hide 21.INSPECT INPUT SHAFT END PLAY

C080727

a.

Using a dial indicator, measure the input shaft end play.

End play:

0.3 to 0.9 mm (0.012 to 0.035 in.)



Hide 22.REMOVE OIL PUMP ASSEMBLY

C203857

a.

Remove the 6 bolts and the oil pump assembly from the transaxle case.


Hide 23.REMOVE INPUT SHAFT ASSEMBLY

C203858

a.

Remove the input shaft assembly from the transaxle case.


Hide 35370A 24.REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C203859

a.

Remove the stator shaft thrust needle roller bearing from the input shaft.


Hide 35667A 25.REMOVE DIRECT CLUTCH DISC

a.
C059966

Using a screwdriver, remove the snap ring, direct clutch flange, 2 direct clutch discs and the 2 direct clutch clutch plates from the input shaft.


Hide 35604 26.REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D025200E02
1.302,0.76 1.5,0.646 false 1.521,0.552 1.813,0.729 0.292,0.177 10 false SST

Using SST, a press and snap ring expander, remove the snap ring and the direct clutch return spring sub-assembly.

SST
09387-00020  


Hide 35606A 27.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C059968

Remove the direct clutch piston sub-assembly by blowing compressed air into the hole as shown in the illustration on the left.


Hide 35606C 28.REMOVE DIRECT CLUTCH PISTON O-RING

a.
U158268

Remove the direct clutch piston O-ring from the direct clutch piston.


b.
U158267

Remove the direct clutch piston O-ring from the input shaft.


Hide 35712A 29.REMOVE INPUT SHAFT OIL SEAL RING

a.
C059970

Remove the 2 input shaft oil seal rings from the input shaft.


Hide 35720J 30.REMOVE PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING

C203860

a.

Remove the planetary gear front thrust needle roller bearing and the thrust bearing race from the direct clutch hub.


Hide 35654B 31.REMOVE DIRECT CLUTCH HUB

C203861

a.

Remove the direct clutch hub from the transaxle case.


Hide 32.REMOVE DIFFERENTIAL GEAR ASSEMBLY

C203862

a.

Remove the differential gear assembly and the differential drive pinion assembly from the transaxle case.


Hide 35148A 33.REMOVE NO. 2 GOVERNOR APPLY GASKET

C059803

a.

Remove the No. 2 governor apply gasket from the transaxle case.


Hide 34.REMOVE TRANSAXLE REAR COVER ASSEMBLY

C203863

a.

Remove the 9 bolts.


b.

Tap around the circumference of the transaxle rear cover with a plastic hammer to remove the transaxle rear cover assembly from the transaxle case.


Hide 34603B 35.REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C248586E01
2.682,0.358 2.995,0.515 0.313,0.157 10 SST 1.817,0.753 2.613,0.438 false 2.208,1.779 2.521,1.936 0.313,0.157 10 SST 1.763,2.101 2.173,1.853 false

Using SST and a press, compress the overdrive brake return spring.

SST
09387-00070  


b.
C248587

Using a screwdriver, remove the snap ring and the overdrive brake return spring sub-assembly.


Hide 34622B 36.REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON

C203890

a.

Remove the 2nd coast and overdrive brake piston from the transaxle rear cover with compressed air.


Hide 34622C 37.REMOVE 2ND COAST AND OVERDRIVE O-RING

a.
C203886

Using a screwdriver, remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.


Hide 35617G 38.REMOVE CLUTCH DRUM OIL SEAL RING

a.
C203887

Remove the 2 clutch drum oil seal rings from the transaxle rear cover.


Hide 35102B 39.REMOVE TRANSAXLE REAR COVER PLUG

a.
C203888

Remove the 3 transaxle rear cover plugs from the transaxle rear cover.


b.

Using a screwdriver, remove the O-rings from the transaxle rear cover plug.


Hide 35149B 40.REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

C203864

a.

Using a screwdriver, remove the 4 transaxle case 2nd brake gaskets.


Hide 35601D 41.REMOVE FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C203865

a.

Using a magnet hand, remove the clutch drum thrust needle roller bearing.


Hide 42.REMOVE INTERMEDIATE SHAFT ASSEMBLY

C203866

a.

Remove the intermediate shaft assembly from the transaxle case.


Hide 35677H 43.REMOVE REVERSE CLUTCH DISC

a.
C059951

Using a screwdriver, remove the snap ring.


b.

Remove the flange, 2 discs and 2 plates from the intermediate shaft.


Hide 35633 44.REMOVE FRONT CLUTCH CLUTCH DISC

a.
C059952

Using a screwdriver, remove the snap ring.


b.

Remove the flange, 4 plates and 4 discs from the intermediate shaft.


Hide 35668 45.REMOVE NO. 1 CLUTCH BALANCER

a.
D025202E02
1.021,0.719 1.229,0.5 false 1.24,0.396 1.531,0.573 0.292,0.177 10 false SST

Using SST, a press and snap ring expander, remove the snap ring.

SST
09387-00020  


b.

Remove the No. 1 clutch balancer from the intermediate shaft.


Hide 35603A 46.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C059954

Remove the forward clutch return spring sub-assembly from the intermediate shaft.


Hide 35612B 47.REMOVE FORWARD CLUTCH PISTON

a.
C059955

Apply compressed air to the transaxle rear cover to remove the forward clutch piston.


Hide 35601 48.REMOVE CLUTCH DRUM SUB-ASSEMBLY

a.
C059956

Apply compressed air to the transaxle rear cover to remove the clutch drum sub-assembly.


Hide 35612C 49.REMOVE FORWARD CLUTCH PISTON O-RING

a.
C059957

Using a screwdriver, remove the forward clutch piston O-ring from the intermediate shaft.


Hide 35601B 50.REMOVE FRONT CLUTCH DRUM O-RING

a.
C059958

Using a screwdriver, remove the front clutch drum O-ring from the clutch drum.


Hide 35748C 51.REMOVE INTERMEDIATE SHAFT OIL SEAL RING

a.
C059959

Using a screwdriver, remove the intermediate shaft oil seal ring from the intermediate shaft.


Hide 35706G 52.REMOVE SUN GEAR REAR THRUST BEARING

C203867

a.

Remove the sun gear rear thrust bearing and the 2 thrust bearing races from the intermediate shaft.


Hide 34633 53.REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC

C203868

a.

Remove the flange, 2 discs and 2 plates from the transaxle case.


Hide 34625E 54.REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C203869

a.

Using a screwdriver, remove the 2nd coast and overdrive flange hole snap ring from the transaxle case.


Hide 35061 55.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C203870

a.

Remove the forward clutch hub sub-assembly from the transaxle case.


Hide 35061C 56.REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C059833

a.

Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub.


Hide 35061B 57.REMOVE FORWARD CLUTCH HUB THRUST BEARING RACE

C059889

a.

Remove the forward clutch hub thrust bearing race from the planetary sun gear.


Hide 35730 58.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

C059834

a.

Remove the rear planetary sun gear assembly from the transaxle case.


Hide 35720K 59.REMOVE PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

C059836

a.

Remove the planetary gear rear thrust needle roller bearing from the rear planetary sun gear.


Hide 35790A 60.INSPECT ONE WAY CLUTCH ASSEMBLY

D025181E05
1.396,1.333 1.594,1.5 0.198,0.167 10 true *c 0.854,0.646 1.021,0.823 0.167,0.177 10 false *a 1.76,0.188 1.927,0.354 0.167,0.167 10 true *b

a.

Hold the rear planetary sun gear and turn the one way clutch.

Text in Illustration
*a Hold
*b Lock
*c Free


b.

Make sure that the one way clutch turns freely clockwise and locks when turned counterclockwise.


Hide 35790A 61.REMOVE ONE WAY CLUTCH ASSEMBLY

C203871

a.

Remove the one way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear.


Hide 35737 62.REMOVE PLANETARY CARRIER THRUST WASHER

C203872

a.

Remove the planetary carrier thrust washer from the transaxle case.


Hide 35706 63.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

C203873

a.

Remove the planetary sun gear sub-assembly from the transaxle case.


Hide 35789 64.REMOVE FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE

C060847

a.

Remove the front planetary flange front thrust bearing race from the planetary sun gear.


Hide 65.REMOVE SECOND BRAKE PISTON ASSEMBLY

C203850E01
1.647,0.466 1.966,0.640 0.319,0.174 10 SST 2.474,1.07 1.975,0.66 1.975,0.66 2.219,1.263 false

a.

Using SST, a press and screwdriver, remove the snap ring.

SST
09387-00100  
09950-70010  (09951-07100)


b.

Remove the second brake piston assembly from the transaxle case.


Hide 35624E 66.REMOVE 2ND BRAKE PISTON

a.
C203884

Remove the 2nd brake piston from the 2nd brake cylinder with compressed air.


Hide 35664D 67.REMOVE 2ND BRAKE CYLINDER O-RING

a.
C203889

Using a screwdriver, remove the 2 2nd brake cylinder O-rings from the 2nd brake piston.


Hide 35608L 68.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C059850

a.

Remove the 2nd brake piston return spring sub-assembly from the transaxle case.


Hide 35682 69.REMOVE 2ND BRAKE BRAKE DISC

C059851

a.

Remove the 2 plates, 2 discs and flange from the transaxle case.


Hide 35159 70.REMOVE BRAKE DRUM GASKET

C059852

a.

Remove the brake drum gasket from the transaxle case.


Hide 34365A 71.REMOVE OUTER RACE RETAINER

C059853

a.

Remove the outer race retainer from the transaxle case.


Hide 35792C 72.INSPECT NO. 2 ONE WAY CLUTCH

a.
D025182

Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.

Text in Illustration
V100135

Lock
V100136

Free


Hide 35792C 73.REMOVE NO. 2 ONE WAY CLUTCH

C203874

a.

Remove the No. 2 one way clutch from the transaxle case.


Hide 35720G 74.REMOVE PLANETARY GEAR ASSEMBLY

C059857

a.

Remove the planetary gear assembly from the transaxle case.


Hide 35683 75.REMOVE 1ST AND REVERSE BRAKE DISC

C203851E03
1.542,0.76 1.042,0.448 1.042,0.448 1.24,0.781 true 0.708,0.323 1.021,0.479 0.313,0.156 10 true SST

a.

Using SST, a press and screwdriver, remove the snap ring.

SST
09387-00100  
09950-70010  (09951-07100)


b.

Remove the flange, 4 discs and 4 plates from the transaxle case.


Hide 35068 76.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C059856

a.

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 35782H 77.REMOVE COUNTER DRIVE GEAR NUT

C355433E01
1.052,2.49 1.667,3.438 1.667,3.438 2.094,2.865 false 1.542,3.5 1.854,3.667 0.313,0.167 10 false SST

a.

Using SST, lift the transaxle case.

SST
09223-15020  
09387-00060  


b.
D025183E02
0.99,1.031 1.365,0.125 false 1.406,0.042 1.698,0.219 0.292,0.177 10 false SST

Using SST and a hammer, release the counter drive gear nut.

SST
09930-00010  


c.
C060713

Using a socket wrench 55 mm, remove the counter drive gear nut from the planetary ring gear flange.

NOTICE:

Remove the nut without unstaking the planetary ring gear.

If a chisel or other tool is used to unstake the planetary ring gear, the impact may damage the bearing.


HINT:

Shift the shift lever to P and fix the counter drive gear.



Hide 35762E 78.REMOVE PLANETARY RING GEAR FLANGE

C203852E01
0.227,0.236 0.536,0.394 0.310,0.158 10 SST 1.28,0.889 0.567,0.348 0.567,0.348 1.202,1.176 false

a.

Using SST and a press, remove the planetary ring gear flange.

SST
09950-60010  (09951-00420)
09950-70010  (09951-07100)


Hide 35743K 79.REMOVE PLANETARY RING GEAR

C203875

a.

Using a screwdriver, remove the snap ring.


b.

Remove the planetary ring gear from the planetary ring gear flange.


Hide 35782C 80.REMOVE COUNTER DRIVE GEAR

C355434

a.

Install the 3 bolts to the counter drive gear.

Bolt (M6):

L = 40 to 80 mm (1.575 to 3.150 in.)

Pitch = 1.0 mm



b.

Rotate the 3 bolts and remove the counter drive gear.


Hide 35623H 81.REMOVE 1ST AND REVERSE BRAKE PISTON

C203876

a.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

NOTICE:
·

Blowing the air may cause the piston to jump out when removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35623J 82.REMOVE 1ST AND REVERSE BRAKE O-RING

C203877

a.

Remove the 2 1st and reverse brake O-rings from the 1st and reverse brake piston.


Hide 35595 83.REMOVE PARKING LOCK PAWL BRACKET

C203878

a.

Remove the 2 bolts and the parking lock pawl bracket.


Hide 35561 84.REMOVE MANUAL VALVE LEVER SHAFT

C059861

a.

Using a screwdriver, cut off the manual valve lever shaft spacer to remove the manual valve lever shaft.


b.
C059887

Using a pin punch and hammer, drive out the spring pin.


c.

Remove the manual valve lever shaft and the manual valve lever.


Hide 35501 85.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

C060849

a.

Remove the parking lock rod sub-assembly from the manual valve lever.


Hide 35409D 86.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

C059863

a.

Remove the bolt and the manual detent spring sub-assembly.


Hide 35557 87.REMOVE PARKING LOCK PAWL

C059862

a.

Remove the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl.


Hide 35104Q 88.REMOVE NO. 1 TRANSAXLE CASE PLUG

C203879

a.

Remove the 2 No. 1 transaxle case plugs from the transaxle housing.


b.

Using a screwdriver, remove the 2 O-rings from the 2 No. 1 transaxle case plugs.


Hide 35104R 89.REMOVE NO. 2 TRANSAXLE HOUSING PLUG

C203880

a.

Remove the No. 2 transaxle housing plug from the transaxle case.


b.

Using a screwdriver, remove the O-ring from the No. 2 transaxle housing plug.


Hide 35506F 90.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C059903

a.

Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.


Hide 31105H 91.REMOVE NO. 2 TRANSAXLE CASE OIL SEAL

C059848

a.

Using a screwdriver and hammer, remove the No. 2 transaxle case oil seal.


Hide 35104F 92.REMOVE TRANSAXLE CASE OIL SEAL

C059798

a.

Using a screwdriver and hammer, remove the transaxle case oil seal.


Hide 35165 93.REMOVE NO. 1 TRANSMISSION CASE PLATE

C203881

a.

Remove the bolt and the No. 1 transmission case plate from the transaxle case.


Hide 35174 94.REMOVE TRANSAXLE HOUSING OIL SEPARATOR

C203882

a.

Remove the 3 bolts and the transaxle housing oil separator from the transaxle housing.


Hide 35195A 95.REMOVE NO. 1 TRANSAXLE APPLY TUBE CLAMP

C203883

a.

Remove the bolt and the No. 1 transaxle apply tube clamp from the transaxle housing.


Hide 35847 96.REMOVE TRANSMISSION LUBE APPLY TUBE

C059794

a.

Remove the transmission lube apply tube from the transaxle housing.

NOTICE:

Do not apply excessive force when removing the apply tube.



Hide 35882A 97.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

C059795

a.

Remove the differential gear lube apply tube from the transaxle housing.

NOTICE:

Do not apply excessive force when removing the apply tube.



Hide 35104B 98.REMOVE NO. 1 BREATHER PLUG

C123279

a.

Remove the No. 1 breather plug from the transaxle case.


b.

Using a screwdriver, remove the O-ring from No. 1 breather plug.