Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248179 AUTOMATIC TRANSAXLE UNIT A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C203905

Hide 2.ADJUST TAPERED ROLLER BEARING PRELOAD

a.

Coat the front differential case and bearing with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.

NOTICE:

Do not install the drive pinion.



b.
C203856

Install the transaxle housing to the transaxle case with the 16 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


c.
D025185E02
2.708,1.677 2.771,1.792 true 2.792,1.729 3.083,1.906 0.292,0.177 10 true SST

Using SST and a torque wrench, measure the preload of the differential gear.

SST
09564-32011  

Preload:
Bearing Standard
New 0.78 to 1.37 N*m (8.0 to 13.9 kgf*cm, 6.9 to 12.2 in.*lbf)
Used 0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)


If the preload is not within the specifications, remove the differential from the transaxle case.

Select a new transaxle case side adjusting shim in accordance with the following table.

Adjusting Shim Thickness:
Mark Thickness
mm (in.)
Mark Thickness
mm (in.)
A 1.80 (0.0709) N 2.26 (0.0890)
B 1.85 (0.0728) P 2.29 (0.0902)
C 1.90 (0.0748) Q 2.32 (0.0913)
D 1.95 (0.768) R 2.35 (0.0925)
E 2.00 (0.0787) S 2.40 (0.0945)
F 2.05 (0.0807) T 2.45 (0.0965)
G 2.08 (0.0819) U 2.50 (0.0984)
H 2.11 (0.0831) V 2.55 (0.1004)
J 2.14 (0.0843) W 2.60 (0.1024)
K 2.17 (0.0854) X 2.65 (0.1043)
L 2.20 (0.0866) Y 2.70 (0.1063)
M 2.23 (0.0878) - -



Hide 35104B 3.INSTALL NO. 1 BREATHER PLUG

C123279

a.

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 1 breather plug.


b.

Install the No. 1 breather plug to the transaxle case.


Hide 35882A 4.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

C059795

a.

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Do not apply excessive force to the apply tube.



Hide 35847 5.INSTALL TRANSMISSION LUBE APPLY TUBE

C059794

a.

Install the transmission lube apply tube to the transaxle housing.

NOTICE:

Do not apply excessive force to the apply tube.



Hide 35195A 6.INSTALL NO. 1 TRANSAXLE APPLY TUBE CLAMP

C059824

a.

Install the No. 1 transaxle apply tube clamp to the transaxle housing with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35174 7.INSTALL TRANSAXLE HOUSING OIL SEPARATOR

C203882

a.

Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35165 8.INSTALL NO. 1 TRANSMISSION CASE PLATE

C059802

a.

Install the No. 1 transmission case plate to the transaxle case with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35104Q 9.INSTALL NO. 1 TRANSAXLE CASE PLUG

U158266

a.

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2 No. 1 transaxle case plugs.


b.

Install the 2 No. 1 transaxle case plugs to the transaxle housing.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35104R 10.INSTALL NO. 2 TRANSAXLE HOUSING PLUG

U158265

a.

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 2 transaxle housing plug.


b.

Install the No. 2 transaxle housing plug to the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35506F 11.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

D025186E02
1.448,0.906 0.917,0.271 0.917,0.271 1.781,1.01 true 0.583,0.198 0.875,0.375 0.292,0.177 10 false SST

a.

Coat a new manual valve lever shaft oil seal with Toyota Genuine ATF Type T-IV.


b.

Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case.

SST
09950-60010  (09951-00210)
09950-70010  (09951-07100)

Oil seal drive in depth:

0.75 to 1.25 mm (0.030 to 0.049 in.)



Hide 35557 12.INSTALL PARKING LOCK PAWL

C059865

a.

Coat the parking lock pawl shaft with Toyota Genuine ATF Type T-IV.


b.

Install the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl to the transaxle case.

NOTICE:

Check that the edge of the torsion spring fits into the groove securely.



Hide 35409D 13.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

C059863

a.

Install the manual detent spring subassembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35501 14.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

C060849

a.

Install the parking lock rod sub-assembly to the manual valve lever.


Hide 35561 15.INSTALL MANUAL VALVE LEVER SHAFT

C355435

a.

Coat the manual valve lever with Toyota Genuine ATF Type T-IV.


b.

Install a new manual valve lever shaft spacer to the manual valve lever.


c.

Install the manual valve lever shaft and the manual valve lever.

NOTICE:

Do not damage the oil seal when installing the manual valve lever shaft.



d.

Using a pin punch and hammer, drive in the spring pin.


e.

Turn the spacer and lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.

Using a pin punch, stake the spacer through the small hole.

Check that the spacer does not turn.


Hide 35595 16.INSTALL PARKING LOCK PAWL BRACKET

C203878

a.

Install the parking lock pawl bracket with the 2 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35623J 17.INSTALL 1ST AND REVERSE BRAKE O-RING

C203877

a.

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 1st and reverse brake piston.


Hide 35623H 18.INSTALL 1ST AND REVERSE BRAKE PISTON

C059900

a.

Coat the 1st and reverse brake piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.

NOTICE:

Do not damage the O-ring of the 1st and reverse brake piston.



Hide 35068 19.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C059856

a.

Coat the 1st and reverse brake return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35683 20.INSTALL 1ST AND REVERSE BRAKE DISC

C082195E04
0.76,1.021 0.927,1.208 0.167,0.188 10 false *1 2.635,0.729 2.802,0.917 0.167,0.188 10 false *2 2.656,1.021 2.823,1.208 0.167,0.188 10 false *3

a.

Coat the 4 plates, 4 discs and flange with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.

Text in Illustration
*1 1st and Reverse Brake Disc
*2 1st and Reverse Brake Flange
*3 1st and Reverse Brake Plate

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



b.
C355436E01
1.688,1.563 1.49,1.948 1.49,1.948 1.688,0.865 false 1.156,1.813 1.448,1.979 0.292,0.167 10 true SST

Using SST, a press and screwdriver, install the snap ring.

SST
09387-00100  
09950-70010  (09951-07100)

NOTICE:

Make sure that the snap ring is installed in the groove of the transaxle case correctly.



Hide 21.INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

D025187E02
1.281,1.01 0.531,0.417 false 0.156,0.333 0.448,0.51 0.292,0.177 10 false SST

a.

Using SST and a dial indicator, measure the 1st and reverse brake piston stroke while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

SST
09350-36010  (09350-06110)

Piston stroke:

0.791 to 1.489 mm (0.031 to 0.057 in.)


If the piston stroke is outside the specifications, inspect the discs, plates and flange.


Hide 35782C 22.INSTALL COUNTER DRIVE GEAR

C355437E01
1.833,1.01 2.438,1.01 2.438,1.01 2.073,1.521 false 1.875,2.792 2.427,1.01 2.427,1.01 2.031,3.25 false 2.531,0.948 2.875,1.115 0.344,0.167 10 false SST

a.

Using SST and a press, install the counter drive gear.

SST
09223-15030  
09387-00060  
09950-60020  (09951-00710)
09950-70010  (09951-07100)

NOTICE:

Do not apply excessive force to the transaxle case.



Hide 35743K 23.INSTALL PLANETARY RING GEAR

C203875

a.

Install the planetary ring gear to the planetary ring gear flange and fix the snap ring using a screwdriver.


Hide 35762E 24.INSTALL PLANETARY RING GEAR FLANGE

C355438E01
1.802,1.031 2.375,1.031 2.375,1.031 2,1.427 false 1.844,2.781 2.365,1.031 2.365,1.031 1.906,3.25 false 2.458,0.938 2.74,1.125 0.281,0.188 10 false SST

a.

Using SST and a press, install the planetary ring gear flange.

SST
09223-15030  
09387-00060  
09950-60010  (09951-00500)
09950-70010  (09951-07100)


Hide 35782H 25.INSTALL COUNTER DRIVE GEAR NUT

a.

Using a socket wrench 55 mm, install a new counter drive gear nut to the planetary ring gear flange.

HINT:

Torque : 100 N*m (1020 kgf*cm, 74 ft.*lbf)



b.
C060714

Inspect the preload of the counter drive gear bearing.

Standard preload:

0.05 to 0.35 N*m (0.5 to 3.5 kgf*cm, 0.45 to 3.09 in.*lbf)


HINT:

Tighten the counter drive gear nut gradually so that the preload is within the specifications.



c.
C355439E01
1.042,2.531 1.677,3.344 1.677,3.344 2.042,2.875 false 1.542,3.344 1.875,3.521 0.333,0.177 10 false SST

Using SST, lift the transaxle case.

SST
09213-14010  
09387-00060  


d.
C060715

Using a chisel and hammer, stake the counter drive gear nut.


Hide 35720G 26.INSTALL PLANETARY GEAR ASSEMBLY

C059857

a.

Coat the planetary gear with Toyota Genuine ATF Type T-IV, and install it to the transaxle housing.


Hide 35792C 27.INSTALL NO. 2 ONE WAY CLUTCH

C203874

a.

Coat the No. 2 one way clutch with Toyota Genuine ATF Type T-IV, and install it to the transaxle.


Hide 35792C 28.INSPECT NO. 2 ONE WAY CLUTCH

a.
D025182

Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.

Text in Illustration
V100135

Lock
V100136

Free


Hide 34365A 29.INSTALL OUTER RACE RETAINER

C059853

a.

Install the outer race retainer in the place shown in the illustration (the space between the No. 2 one way clutch outer race and transaxle case). Push the outer race retainer in until it makes a click sound.


Hide 35159 30.INSTALL BRAKE DRUM GASKET

C059852

a.

Coat a new brake drum gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35682 31.INSTALL 2ND BRAKE BRAKE DISC

D025188E04
0.625,0.573 0.813,0.75 0.188,0.177 10 false *1 2.604,0.854 2.938,1.031 0.333,0.177 10 false *3 2.604,1.208 3.042,1.385 0.438,0.177 10 false *2

a.

Coat the flange, 2 discs and 2 plates with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.

Text in Illustration
*1 2nd Brake Brake Disc
*2 2nd Brake Brake Flange
*3 2nd Brake Brake Plate

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35608L 32.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C059850

a.

Coat the 2nd brake piston return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35664D 33.INSTALL 2ND BRAKE CYLINDER O-RING

a.
C203889

Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd brake piston.

NOTICE:

Do not damage the O-rings.



Hide 35664C 34.INSTALL 2ND BRAKE PISTON

a.
C203885

Coat the 2nd brake piston with Toyota Genuine ATF Type T-IV, and install it to the 2nd brake cylinder.

NOTICE:

Do not damage the O-rings.



Hide 35.INSTALL SECOND BRAKE PISTON ASSEMBLY

C060853

a.

Coat the second brake piston assembly with Toyota Genuine ATF Type T-IV, and install it as shown in the illustration.


b.
C355440E01
2.26,1.208 1.948,0.615 1.948,0.615 2.479,1.083 false 1.604,0.552 1.917,0.729 0.313,0.177 10 false SST

Using SST, a press and screwdriver, install the snap ring.

SST
09387-00100  
09950-70010  (09951-07100)


Hide 35789 36.INSTALL FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE

C060847

a.

Coat the front planetary flange front thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the front planetary sun gear.


Hide 35706 37.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

C203873

a.

Coat the planetary sun gear sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 34625E 38.INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C203869

a.

Using a screwdriver, install the 2nd coast and overdrive flange hole snap ring to the transaxle case.


Hide 35737 39.INSTALL PLANETARY CARRIER THRUST WASHER

C203872

a.

Coat the planetary carrier thrust washer with petroleum jelly, and install it to the planetary gear.


Hide 35790A 40.INSTALL ONE WAY CLUTCH ASSEMBLY

C203871

a.

Coat the No. 2 planetary carrier thrust washer with petroleum jelly.


b.

Install No. 2 planetary carrier thrust washer and the one way clutch to the planetary sun gear.


Hide 35790A 41.INSPECT ONE WAY CLUTCH ASSEMBLY

D025181E05
1.396,1.333 1.594,1.5 0.198,0.167 10 true *c 0.854,0.646 1.021,0.823 0.167,0.177 10 false *a 1.76,0.188 1.927,0.354 0.167,0.167 10 true *b

a.

Hold the rear planetary sun gear and turn the one way clutch.

Text in Illustration
*a Hold
*b Lock
*c Free


b.

Make sure that the one way clutch turns freely counterclockwise and locks when turned clockwise.


Hide 35720K 42.INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

C059836

a.

Coat the planetary gear rear thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the rear planetary gear.


Hide 35730 43.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

C059834

a.

Coat the rear planetary sun gear assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35061B 44.INSTALL FORWARD CLUTCH HUB THRUST BEARING RACE

C059889

a.

Coat the forward clutch hub thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35061C 45.INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C059833

a.

Coat the forward clutch hub thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the forward clutch hub.


Hide 35061 46.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

C203870

a.

Coat the forward clutch hub sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35748C 47.INSTALL INTERMEDIATE SHAFT OIL SEAL RING

a.
C059959

Coat a new intermediate shaft oil seal ring with Toyota Genuine ATF Type T-IV, and install it to the clutch drum.


Hide 35601B 48.INSTALL FRONT CLUTCH DRUM O-RING

a.
C059958

Coat a new front clutch drum O-ring with Toyota Genuine ATF Type T-IV, and install it to the clutch drum.


Hide 35612C 49.INSTALL FORWARD CLUTCH PISTON O-RING

a.
C059957

Coat a new forward clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.


Hide 35601 50.INSTALL CLUTCH DRUM SUB-ASSEMBLY

a.
C059963

Coat the clutch drum sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.


Hide 35612B 51.INSTALL FORWARD CLUTCH PISTON

a.
C059964

Coat the forward clutch piston with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.


Hide 35603A 52.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C059954

Coat the forward clutch return spring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.


Hide 35668 53.INSTALL NO. 1 CLUTCH BALANCER

a.

Coat the No. 1 clutch balancer with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft.


b.
D025202E02
1.021,0.719 1.229,0.5 false 1.24,0.396 1.531,0.573 0.292,0.177 10 false SST

Using SST, a press and snap ring expander, install the snap ring.

SST
09387-00020  


Hide 35633 54.INSTALL FRONT CLUTCH CLUTCH DISC

a.
D025203E04
2.906,0.302 3.344,0.479 0.438,0.177 10 false *2 2.927,0.51 3.26,0.688 0.333,0.177 10 false *3 0.771,0.469 0.948,0.646 0.177,0.177 10 false *1

Coat the 4 plated, 4 discs and flange with Toyota Genuine ATF Type T-IV, and install them to the intermediate shaft with the snap ring.

Text in Illustration
*1 Front Clutch Clutch Disc
*2 Front Clutch Clutch Flange
*3 Forward Plate


Hide 35677H 55.INSTALL REVERSE CLUTCH DISC

a.
D025204E04
2.76,0.333 3.198,0.51 0.438,0.177 10 false *2 2.76,0.719 3.094,0.896 0.333,0.177 10 false *3 1.01,0.563 1.188,0.74 0.177,0.177 10 false *1

Coat the 2 plates, 2 discs and clutch flange with Toyota Genuine ATF Type T-IV, and install them with the snap ring to the intermediate shaft.

Text in Illustration
*1 Reverse Clutch Disc
*2 Reverse Clutch Flange
*3 Reverse Clutch Plate


Hide 35649 56.INSPECT PACK CLEARANCE OF REVERSE CLUTCH

a.
C059938

Install the intermediate shaft to the transaxle rear cover.


b.

Using a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

Standard clearance:

0.4 to 1.0 mm (0.0157 to 0.0394 in.)


NOTICE:

If the clearance is outside the specifications, select a new flange.


Flange Thickness
Mark Thickness
1 3.0 mm (0.118 in.)
2 3.2 mm (0.126 in.)
3 3.4 mm (0.135 in.)
4 3.6 mm (0.142 in.)


Hide 35635 57.INSPECT PACK CLEARANCE OF FRONT CLUTCH

a.
C355441E01
1.979,0.917 1.271,0.292 false 1.083,0.094 1.375,0.271 0.292,0.177 10 false SST

Install the intermediate shaft to the transaxle rear cover.


b.

Using SST and a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

SST
09350-36010  (09350-06120)

Standard clearance:

1.3 to 1.5 mm (0.0512 to 0.0591 in.)


NOTICE:

If the clearance is outside the specifications, select a new flange.


Flange Thickness
Mark Thickness
1 3.0 mm (0.118 in.)
2 3.2 mm (0.126 in.)
3 3.4 mm (0.135 in.)
4 3.6 mm (0.142 in.)


Hide 35706G 58.INSTALL SUN GEAR REAR THRUST BEARING

C203867

a.

Coat the sun gear rear thrust bearing and the 2 thrust bearing races with Toyota Genuine ATF Type T-IV, and install them to the intermediate shaft.


Hide 59.INSTALL INTERMEDIATE SHAFT ASSEMBLY

C203866

a.

Coat the intermediate shaft assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 34633 60.INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC

D025189E04
2.698,0.625 2.698,1.021 false 2.385,0.823 2.813,0.823 false 0.531,1.031 0.698,1.208 0.167,0.177 10 false *1 2.813,0.771 3.042,0.958 0.229,0.188 10 false *2

a.

Coat the 2 discs and 3 flanges with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.

Text in Illustration
*1 2nd Coast and Overdrive Brake Disc
*2 2nd Coast and Overdrive Brake Flange

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35102B 61.INSTALL TRANSAXLE REAR COVER PLUG

a.
C203888

Coat 4 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover plug.


b.

Install the 3 transaxle rear cover plugs to the transaxle rear cover.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-rings.



Hide 35617G 62.INSTALL CLUTCH DRUM OIL SEAL RING

a.
D025205E02
0.646,0.188 0.781,0.375 0.135,0.188 10 false A

Compress the clutch drum oil seal ring from both sides to reduce dimension A.

Dimension A:

5.0 mm (0.197 in.)



b.

Coat the 2 clutch drum oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover.


Hide 34622C 63.INSTALL 2ND COAST AND OVERDRIVE O-RING

a.
C203886

Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd coast overdrive brake piston.

NOTICE:

Do not damage the O-rings.



Hide 34622B 64.INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C060025

Coat the 2nd coast and overdrive brake piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle rear cover.


Hide 34603B 65.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C248587

Coat the overdrive brake return spring sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle rear cover.


b.
C248586E01
2.682,0.358 2.995,0.515 0.313,0.157 10 SST 1.817,0.753 2.613,0.438 false 2.208,1.779 2.521,1.936 0.313,0.157 10 SST 1.763,2.101 2.173,1.853 false

Using SST and a press, shorten the overdrive brake return spring, then install the snap ring.

SST
09387-00070  


Hide 66.INSPECT 2ND COAST AND OVER DRIVE BRAKE FLANGE, DISC AND PLATE

C355442E01
0.271,0.396 0.396,0.573 0.125,0.177 10 false A

a.

Using a straightedge and vernier caliper, measure dimension A from the transaxle case end surface to the brake flange.


b.
C355443E01
3.083,0.635 3.219,0.813 0.135,0.177 10 false B

Using a straightedge and vernier caliper, measure dimension B from the piston to the edge surface of the transaxle rear cover assembly.


c.

Calculate the clearance from the measured dimensions A and B.

Piston clearance:

0.65 to 1.05 mm (0.0256 to 0.0413 in.)


HINT:
·

Piston clearance = Dimension A - Dimension B.

·

If the result is not as specified, select a new brake flange.



Flange Thickness
Mark Thickness
mm (in.)
Piston Stroke Value
mm (in.)
0 3.0
(0.118)
0.738 to 0.949
(0.02905 to 0.03736)
1 3.2
(0.126)
0.950 to 1.149
(0.03740 to 0.04524)
2 3.4
(0.134)
1.150 to 1.349
(0.04528 to 0.05311)
3 3.6
(0.142)
1.350 to 1.549
(0.05315 to 0.06098)
4 3.8
(0.150)
1.550 to 1.702
(0.06102 to 0.06701)


Hide 35149B 67.INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

C203864

a.

Coat 4 new transaxle case 2nd brake gaskets with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover.


Hide 35601D 68.INSTALL FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C203865

a.

Coat the front clutch drum thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the forward and reverse clutch.


Hide 69.INSTALL TRANSAXLE REAR COVER ASSEMBLY

C059899E01
0.281,0.74 0.452,0.911 0.171,0.171 10 *a 0.88,0.847 0.471,0.847 false

a.

Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle rear cover.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
C203863

Install the transaxle rear cover assembly to the transaxle case with the 9 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 35148A 70.INSTALL NO. 2 GOVERNOR APPLY GASKET

C059803

a.

Coat a new No. 2 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 71.INSTALL DIFFERENTIAL GEAR ASSEMBLY

C203862

a.

Coat the differential gear assembly and the drive pinion assembly with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.


Hide 35654B 72.INSTALL DIRECT CLUTCH HUB

C203861

a.

Coat the direct clutch hub with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35720J 73.INSTALL PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING

C203860

a.

Coat the planetary gear front thrust needle roller bearing and the thrust bearing race with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.


Hide 35712A 74.INSTALL INPUT SHAFT OIL SEAL RING

a.
C059970

Coat 2 new input shaft oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the input shaft.


Hide 35606C 75.INSTALL DIRECT CLUTCH PISTON O-RING

a.
U158268

Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the direct clutch.


b.
U158267

Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the input shaft.


Hide 35606A 76.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C059974

Coat the direct clutch piston with Toyota Genuine ATF Type T-IV, and install it to the input shaft.


Hide 35604 77.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D025200E02
1.302,0.76 1.5,0.646 false 1.521,0.552 1.813,0.729 0.292,0.177 10 false SST

Using SST, a press and snap ring expander, install the direct clutch return spring subassembly to the input shaft with the snap ring.

SST
09387-00020  


Hide 35667A 78.INSTALL DIRECT CLUTCH DISC

a.
C355444E01
2.125,0.865 2.479,0.458 false 2,1.156 2.656,0.969 2.656,0.969 1.99,0.969 false 2.125,1.24 2.708,1.542 2.708,1.542 2.125,1.063 false 2.542,0.313 2.719,0.49 0.177,0.177 10 false *1 2.74,0.885 2.917,1.063 0.177,0.177 10 false *2 2.76,1.469 2.938,1.646 0.177,0.177 10 false *3

Coat the direct clutch flange, 2 direct clutch discs and the 2 direct clutch clutch plates with Toyota Genuine ATF Type T-IV, and install them to the input shaft with the snap ring.

Text in Illustration
*1 Direct Clutch Flange
*2 Direct Clutch Disc
*3 Direct Clutch Clutch Plate


Hide 35675C 79.INSPECT PISTON STROKE OF DIRECT CLUTCH

C059977

a.

Install the input shaft assembly onto the oil pump.


b.

Using a dial indicator, measure the clearance while applying compressed air (400 kPa, 4.1 kgf/cm2, 58 psi).

Standard clearance:

0.4 to 0.7 mm (0.0157 to 0.0276 in.)


NOTICE:

If the clearance is outside the specifications, select a new flange.


Flange Thickness
Mark Thickness
1 3.0 mm (0.118 in.)
2 3.2 mm (0.126 in.)
3 3.4 mm (0.135 in.)


Hide 35370A 80.INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C203859

a.

Coat the stator shaft thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.

NOTICE:

Check the direction of the bearing.



Hide 81.INSTALL INPUT SHAFT ASSEMBLY

C203858

a.

Coat the input shaft assembly with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 82.INSTALL OIL PUMP ASSEMBLY

C203857

a.

Place the oil pump assembly through the input shaft, and align the bolt holes in the oil pump assembly with those in the transaxle case.


b.

Install the 6 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 83.INSPECT INPUT SHAFT ASSEMBLY

C080729

a.

Make sure that the input shaft turns smoothly.


Hide 84.INSPECT INPUT SHAFT END PLAY

C080727

a.

Using a dial indicator, measure the input shaft end play.

End play:

0.3 to 0.9 mm (0.012 to 0.035 in.)


If the end play is not as specified, select and replace the thrust needle roller bearing.


Hide 35111C 85.INSTALL TRANSAXLE HOUSING

C059886E02
0.927,1.906 1.167,1.531 false 0.729,1.875 0.917,2.063 0.188,0.188 10 false *a

a.

Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle housing.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
U158278

Install the transaxle housing to the transaxle case with the 16 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:

Apply adhesive or the equivalent to the 4 bolts indicated by arrows.


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



Hide 35427P 86.INSTALL B-1 ACCUMULATOR PISTON COMPRESSION SPRING

C060004

a.

Install the B-1 accumulator piston compression spring to the B-1 accumulator piston.


Hide 35427R 87.INSTALL B-1 ACCUMULATOR PISTON

D025193

a.

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the B-1 accumulator piston.


b.
C060822

Coat the B-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


c.

Install the No. 2 B-1 accumulator compression spring.


Hide 35206 88.INSTALL C-1 ACCUMULATOR SPRING SUB-ASSEMBLY

C059790

a.

Install the C-1 accumulator spring to the C-1 accumulator piston.


Hide 35424C 89.INSTALL C-1 ACCUMULATOR PISTON

D025194

a.

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-1 accumulator piston.


b.
C203854

Coat the C-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35209 90.INSTALL C-2 ACCUMULATOR SPRING SUB-ASSEMBLY

C059787

a.

Using a screwdriver, install the C-2 accumulator spring to the C-2 accumulator piston with the snap ring.


Hide 35425A 91.INSTALL C-2 ACCUMULATOR PISTON

D025195

a.

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-2 accumulator piston.


b.
C203853

Coat the C-2 accumulator piston with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35251 92.INSTALL CHECK BALL BODY

C059785

a.

Coat the compression spring and the check ball body with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.


Hide 35148 93.INSTALL NO. 1 GOVERNOR APPLY GASKET

C059784

a.

Coat new No. 1 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 82125J 94.INSTALL TRANSMISSION WIRE

a.

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the transmission wire.


b.
C203903

Insert the transmission wire into the transaxle case.


c.
C203904

Install the transmission wire with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35410 95.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

U158257

a.

Connect the manual valve control rod to the manual valve lever, and install the transmission valve body assembly.


b.
C203895E03
1.573,1.417 1.573,1.948 true 1.302,1.438 1.302,1.927 true 0.885,0.771 0.417,0.771 true 0.99,1.5 0.469,1.094 0.469,1.094 0.948,1.156 false 0.719,1.396 0.458,1.094 0.458,1.094 0.781,1.677 false 0.74,1.042 0.479,1.094 false 1.729,0.385 1.854,0.167 1.854,0.167 1.99,0.417 false 2.26,0.375 1.854,0.167 1.854,0.167 1.375,0.396 false 2.469,1.042 3.073,1.219 3.073,1.219 2,1.354 true 3.125,1.156 3.281,1.333 0.156,0.177 10 false A 1.802,0.01 1.927,0.167 0.125,0.156 10 false A 0.313,1.042 0.469,1.219 0.156,0.177 10 false B 0.292,0.688 0.448,0.865 0.156,0.177 10 false E 1.26,1.948 1.417,2.125 0.156,0.177 10 false C 1.531,1.958 1.688,2.135 0.156,0.177 10 false D

Install the 14 bolts to the positions shown in the illustration and tighten them uniformly.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:

When installing the transmission valve body assembly to the transaxle case, do not hold the solenoids.


Bolt length:
Bolt A:

20 mm (0.787 in.)

Bolt B:

28 mm (1.102 in.)

Bolt C:

49 mm (1.929 in.)

Bolt D:

36 mm (1.417 in.)

Bolt E:

40 mm (1.575 in.)



Hide 82125J 96.CONNECT TRANSMISSION WIRE

a.
C203893

Install the transmission wire with the clamp.


b.

Connect the 5 connectors to the transmission valve body assembly.


Hide 35330 97.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C057509

a.

Coat a new oil strainer gasket with Toyota Genuine ATF Type T-IV and install it to the valve body oil strainer assembly.


b.
C203892

Install the valve body oil strainer assembly with the 3 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35106D 98.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

U158258

a.

Install the 2 oil cleaner magnets to the 2 positions shown in the illustration.


b.
C203891

Install a new oil pan gasket and the automatic transaxle oil pan sub-assembly to the transaxle assembly with 18 bolts.

Torque:
7.0 N*m (70 kgf*cm, 61 in.*lbf)


c.

Install a new gasket and the drain plug to the automatic transaxle oil pan sub-assembly.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 31105H 99.INSTALL NO. 2 TRANSAXLE CASE OIL SEAL

C203932E03
1.188,2.854 1.375,3.104 1.375,3.104 1.51,2.781 false 1.365,0.885 0.823,0.302 0.823,0.302 1.708,0.875 true 1.229,3.146 1.563,3.313 0.333,0.167 10 false SST 0.5,0.208 0.833,0.375 0.333,0.167 10 false SST

a.

Using SST and a hammer, install a new No. 2 transaxle case oil seal.

SST
09517-12010  
09630-24014  (09620-24051)

Drive in depth:

2.6 to 3.6 mm (0.103 to 0.141 in.)



b.

Apply MP grease to the lip of the No. 2 transaxle case oil seal.


Hide 35104F 100.INSTALL TRANSAXLE CASE OIL SEAL

C203934E03
1.292,2.844 1.292,3.094 false 1.156,1.354 1.156,1.958 true 1.167,3.115 1.5,3.281 0.333,0.167 10 false SST 1.031,1.99 1.365,2.156 0.333,0.167 10 false SST

a.

Using SST and a hammer, install a new transaxle case oil seal.

SST
09316-60011  (09316-00011)

Drive in depth:

2.6 to 3.6 mm (0.103 to 0.141 in.)



b.

Apply MP grease to the lip of the transaxle case oil seal.


Hide 32921C 101.INSTALL OIL COOLER TUBE UNION

U158264

a.

Coat 2 new O-rings with ATF Type T-IV, and install them to the 2 oil cooler tube unions.


b.

Install the 2 oil cooler tube unions.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 35104V 102.INSTALL BREATHER PLUG HOSE

U158263

a.

Install the breather plug hose to the breather plug with the clamp.


Hide 89413B 103.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C117099E03
1.865,1.875 2.115,1.875 false 2.188,1.792 2.385,1.99 0.198,0.198 10 false *1

Coat a new O-ring with ATF Type T-IV, and install it to the transmission revolution sensor.

Text in Illustration
*1 O-ring


b.
U158259

Install the transmission revolution sensor to the transaxle assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 84540 104.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C107763

a.

Install the park/neutral position switch assembly.


b.

Temporarily install the 2 bolts.


c.
C244577

Replace the lock plate with a new one and install the nut, lock plate and washer.


d.

Temporarily install the 2 bolts.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.

Temporarily install the control shaft lever.


f.
C107759

Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.


g.
U158282E02
0.708,0.583 1.417,0.896 false 0.708,1.281 1.49,1.177 false 0.458,0.448 0.646,0.656 0.188,0.208 10 true *a 0.521,1.188 0.708,1.396 0.188,0.208 10 false *b

Align the groove and the neutral basic line., and tighten the 2 bolts.

Text in Illustration
*a Neutral Basic Line
*b Groove

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


h.
C107761

Using a screwdriver, stake the nut with the lock washer.


Hide 35572A 105.INSTALL TRANSMISSION CONTROL SHAFT LEVER

C107764

a.

Install the control shaft lever with the washer and nut.

Torque:
12 N*m (125 kgf*cm, 9 ft.*lbf)