Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248181 DIFFERENTIAL CASE A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL DIFFERENTIAL GEAR KIT

C060003

a.

Coat the differential gear kit ((2 front differential pinions and 2 front differential side gears), 2 front differential side gear thrust washers and the 2 front differential pinion thrust washers with Toyota Genuine ATF Type T-IV, and install them to the front differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

U158270

a.

Install the front No. 1 differential pinion shaft so as to align the straight pin holes in the front No. 1 differential pinion shaft and the front differential case.


Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

C060005

a.

Using a pin punch 3 mm and hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C060006

Using a chisel and hammer, stake the front differential case.


Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

D025177

a.

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

CAUTION:

Use thick gloves to protect your hands as the front differential ring gear is hot.



b.

Clean the contact surface of the front differential case and the front differential ring gear.


c.
C123274E03
1.615,1.521 2.271,1.969 false 1.583,1.625 2.271,1.969 false 2.292,1.865 2.458,2.021 0.167,0.156 10 false *a

Align the matchmarks on the front differential ring gear and the front differential case, and install the front differential ring gear while it is still hot.

Text in Illustration
*a Matchmark


d.
U158295

Tighten the 8 bolts.

Torque:
78 N*m (790 kgf*cm, 57 ft.*lbf)


Hide 33481X 6.INSTALL SPEEDOMETER DRIVE GEAR (w/o ABS)

U158294

a.

Install the speedometer drive gear to the front differential case.


Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C123276E01
0.706,0.38 1.024,0.689 0.318,0.309 10 SST 1.079,0.466 1.566,0.672 false

a.

Using SST and a press, install the front differential case front tapered roller bearing (inner race) to the front differential case.

SST
09608-06041  


b.
D025217E04
1.26,0.896 0.844,0.563 0.844,0.563 1.156,1.479 false 0.479,0.479 0.771,0.656 0.292,0.177 10 false SST

Using SST and a hammer, install the front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07100)
09950-60010  (09951-00340)


Hide 41311F 8.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C123277E01
2.666,0.959 2.970,1.272 0.304,0.313 10 SST 1.869,0.672 2.631,1.05 2.631,1.05 1.875,1.744 false

a.

Using SST and a press, install the front differential case rear tapered roller bearing (inner race) to the front differential case.

SST
09608-06041  


b.
D025219E06
1.542,0.896 2.354,1.625 2.354,1.625 1.646,1.458 false 2.396,1.552 2.688,1.729 0.292,0.177 10 false SST

Using SST and a hammer, install the front differential case rear plate washer and the front differential case rear tapered roller bearing (outer race) to the transaxle case.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


Hide 41211E 9.INSTALL DIFFERENTIAL DRIVE PINION PLUG

C060013

a.

Using a socket wrench 10 mm and hammer, install a new differential drive pinion plug to the differential drive pinion.

Drive in depth:

2.3 to 2.35 mm (0.0906 to 0.0925 in.)



Hide 41211A 10.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

D025220E02
1.771,0.854 2.094,0.854 false 2.125,0.76 2.417,0.938 0.292,0.177 10 false SST

a.

Using SST and a press, install the front drive pinion front tapered roller bearing (inner race) to the differential drive pinion.

SST
09608-04031  
09950-60010  (09951-00540)


b.
D025227E02
1.573,0.677 1.01,0.396 1.01,0.396 1.458,1.354 false 0.667,0.292 0.958,0.469 0.292,0.177 10 false SST

Using SST and a hammer, install the front drive pinion front tapered roller bearing (outer race) to the transaxle housing.

SST
09608-04031  
09950-70010  (09951-07100)


Hide 35782C 11.INSTALL COUNTER DRIVE GEAR

D025228E02
1.75,0.625 2.365,1.125 2.365,1.125 1.719,1.708 false 2.396,1.031 2.688,1.208 0.292,0.177 10 false SST

a.

Using SST and a press, install the counter drive gear to the differential drive pinion.

SST
09608-04031  
09950-60010  (09951-00280)


Hide 41211B 12.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

D025229E02
1.75,0.604 2.323,0.906 2.323,0.906 1.74,1.688 false 2.354,0.813 2.646,0.99 0.292,0.177 10 false SST

a.

Using SST and a press, install the front drive pinion rear tapered roller bearing (inner race) to the differential drive pinion.

SST
09608-04031  
09950-60010  (09951-00280)


b.
D025230E02
1.375,1.521 0.969,0.531 0.969,0.531 1.458,0.958 false 0.615,0.448 0.906,0.625 0.292,0.177 10 false SST

Using SST and a hammer, install the drive pinion washer and the front drive pinion rear tapered roller bearing (outer race) to the transaxle case.

SST
09950-60010  (09951-00600)
09950-70010  (09951-07100)