Home › Drivetrain › U441E (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER
RM19S0E _52 Drivetrain _051466 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0248182 SHIFT LEVER G

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LOCK CONTROL ECU (for Integrated Type Shift Lock Control ECU)

a.
C266263E01
0.122,0.044 0.489,0.395 0.367,0.351 10 *a 0.163,1.148 0.534,1.347 0.371,0.199 10 IG 0.163,1.658 0.534,1.857 0.371,0.199 10 STP 1.156,1.762 1.527,1.961 0.371,0.199 10 E 2.772,1.658 3.143,1.857 0.371,0.199 10 KLS+ 2.772,1.148 3.143,1.347 0.371,0.199 10 ACC 0.43,1.229 1.328,1.065 false 0.537,1.736 1.323,1.328 false 1.302,1.848 1.573,1.354 false 2.733,1.736 2.093,1.325 false 2.733,1.238 2.093,1.056 false

Measure the voltage according to the value(s) in the table below.

Text in Illustration
*a Component with harness connected
(Shift Lock Control ECU)

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - 7 (E) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (IG) - 7 (E) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
5 (KLS+) - 7 (E) Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
8 (STP) - 7 (E) Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


NOTICE:

Do not disconnect the shift lock control unit assembly connector.


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control unit assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


NOTICE:

Do not disconnect the shift lock control unit assembly connector.


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control unit assembly.


Hide 2.INSPECT SHIFT LOCK CONTROL ECU (for Separate Type Shift Lock Control ECU)

a.
C197449E09
0.067,0.049 0.244,0.212 0.177,0.163 10 *a 0.265,0.586 0.553,0.741 0.288,0.154 10 STP 0.415,1.536 0.594,1.690 0.178,0.154 10 IG 1.694,1.813 2.030,1.968 0.336,0.154 10 ACC 2.861,1.484 3.250,1.638 0.389,0.154 10 KLS+ 2.832,0.561 2.988,0.716 0.156,0.154 10 E 1.865,1.798 1.865,1.384 false 2.263,0.963 2.796,0.685 false 2.263,1.275 2.796,1.553 false 1.186,0.963 0.653,0.685 false 1.186,1.275 0.653,1.553 false

Measure the voltage according to the value(s) in the table below.

Text in Illustration
*a Component with harness connected
(Shift Lock Control ECU)

Standard Voltage:
Tester Connection Condition Specified Condition
6 (ACC) - 1 (E) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
8 (IG) - 1 (E) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
5 (KLS+) - 1 (E) Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
4 (STP) - 1 (E) Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


NOTICE:

Do not disconnect the shift lock control ECU connector.


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


NOTICE:

Do not disconnect the shift lock control ECU connector.


If the result is not as specified and there are no problems with the wire harness, replace the shift lock control ECU.


Hide 3.INSPECT TRANSMISSION CONTROL SWITCH

a.
C197451E15
0.052,0.057 0.228,0.206 0.177,0.149 10 *a 2.344,0.111 2.667,0.260 0.323,0.149 10 ATD 2.73,0.348 3.028,0.497 0.298,0.149 10 AT3 2.827,0.815 3.244,0.964 0.416,0.149 10 NSSD 1.839,1.097 2.303,0.197 false 2.004,1.097 2.695,0.438 false 2.2,1.187 2.793,0.906 false

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Text in Illustration
*a Component without harness connected
(Transmission Control Switch)

Standard Resistance:
Tester Connection Shift Position Specified Condition
1 (NSSD) - 2 (AT3) 3 and 2 Below 1 Ω
Except 3 and 2 10 kΩ or higher
1 (NSSD) - 3 (ATD) Except 3 and 2 Below 1 Ω
3 and 2 10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.


Hide 4.INSPECT SHIFT LOCK SOLENOID (for Separate Type Shift Lock Control ECU)

a.

Disconnect the shift lock solenoid connector.


b.
C197452E10
0.067,0.0 0.233,0.153 0.167,0.153 10 *a 0.443,1.564 0.821,1.776 0.378,0.212 10 SLS+ 1.203,1.564 1.599,1.776 0.396,0.212 10 SLS- 2.084,1.564 2.31,1.776 0.226,0.212 10 E2 2.763,1.564 2.989,1.776 0.226,0.212 10 P 1.401,1.167 0.647,1.545 false 1.63,1.167 1.398,1.564 false 1.859,1.167 2.151,1.545 false 2.091,1.167 2.782,1.537 false

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Text in Illustration
*a Component without harness connected
(Shift Lock Solenoid)

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Except P Below 1 Ω


If the result is not as specified, replace the shift lock control unit assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) When battery voltage not applied 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.