Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248200 MANUAL TRANSAXLE UNIT A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101A 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

C080549

a.

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 2.REMOVE DRAIN PLUG SUB-ASSEMBLY

C080550

a.

Remove the drain plug sub-assembly and gasket from the manual transmission case.


Hide 84210 3.REMOVE BACK UP LIGHT SWITCH ASSEMBLY

C120749E01
1.504,1.722 1.857,1.897 0.353,0.175 10 SST 2.092,1.28 1.668,1.704 false

a.

Separate the back up light switch wire harness from the 2 clamps.


b.

Using SST, remove the back up light switch assembly and gasket from the manual transmission case.

SST
09817-16011  


Hide 4.REMOVE SELECTING BELL CRANK ASSEMBLY

C120750

a.

Remove the 2 bolts, nut and the selecting bell crank assembly from the manual transmission case.


b.

Remove the control bell crank dust cover.


Hide 33527 5.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER

C120748

a.

Remove the nut and spring washer.


b.
C120747

Using a brass bar and a hammer, remove the lock pin.


c.

Remove the floor shift control shift lever and the dust boot.


Hide 33544C 6.REMOVE SHIFT LEVER DAMPER

C120746

a.

Remove the nut and spring washer.


b.
C120745

Using a brass bar and a hammer, remove the lock pin.


c.

Remove the shift lever damper and dust boot.


Hide 30300 7.FIX MANUAL TRANSAXLE ASSEMBLY

a.
C080552E10
1.135,1.865 0.802,1.021 0.802,1.021 2.479,1.781 false 1.135,1.865 0.802,1.021 0.802,1.021 2.479,1.781 false 0.594,0.885 0.76,1.073 0.167,0.188 10 false *1

Place the manual transaxle assembly on wooden blocks.

Text in Illustration
*1 Wooden Block


Hide 33290 8.REMOVE NO. 1 LOCK BALL ASSEMBLY

C120744

a.

Remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33295A 9.REMOVE SHIFT GATE PIN

C120743

a.

Remove the shift gate pin and washer from the manual transmission case.


Hide 33528B 10.REMOVE CONTROL SHAFT COVER

C120742

a.

Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.


Hide 33528C 11.REMOVE CONTROL SHAFT COVER OIL SEAL

C120741

a.

Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.


Hide 12.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

C120740

a.

Remove the shift and select lever shaft assembly from the manual transmission case.


Hide 33102 13.REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

C080554

a.

Remove the 9 bolts.


b.
C355248

Using a plastic hammer, carefully tap the projection of the manual transmission case cover sub-assembly to remove the manual transmission case cover sub-assembly from the manual transmission case.

Text in Illustration
V100135

Projection Part

NOTICE:

Do not damage the manual transmission case.



Hide 33321G 14.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

C251589E01
1.841,1.115 2.361,0.939 false 2.381,0.851 2.703,1.019 0.323,0.167 10 SST

a.

Using a SST and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.

SST
09930-00010  


b.
Q006512

Engage the 2 gears simultaneously to lock the transmission.


c.

Remove the manual transmission output shaft rear set nut.


d.

Disengage the 2 gears.


Hide 33214G 15.REMOVE NO. 3 GEAR SHIFT FORK

C080342

a.

Remove the shift fork set bolt from the No. 3 gear shift fork.


b.
C080343

Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.


Hide 33336 16.INSPECT 5TH GEAR THRUST CLEARANCE

C080344

a.

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, the 5th gear or input shaft rear radial ball bearing.


Hide 33336 17.INSPECT 5TH GEAR RADIAL CLEARANCE

C080345

a.

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft assembly.


Hide 33393 18.REMOVE NO. 3 TRANSMISSION CLUTCH HUB

a.
C080346

Using 2 screwdrivers and a hammer, tap out the No. 3 clutch hub shaft snap ring.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C157373

Using a screwdriver, remove the synchromesh shifting key spring from the No. 3 transmission clutch hub.


c.
D032344E04
1.031,0.979 0.594,1.406 0.594,1.406 1.177,1.438 false 0.24,1.323 0.531,1.5 0.292,0.177 10 false SST

Using SST, remove the No. 3 transmission clutch hub, 5th gear, and the No. 3 synchronizer ring from the input shaft assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60010  (09951-00200)


d.
D032357

Remove the 3 synchromesh shifting keys and the synchromesh shifting key spring from the No. 3 transmission clutch hub.


Hide 33336A 19.REMOVE 5TH GEAR NEEDLE ROLLER BEARING

U158273

a.

Remove the 5th gear needle roller bearing and the 5th gear bearing spacer from the input shaft assembly.


Hide 33428C 20.REMOVE 5TH DRIVEN GEAR

C080349E01
0.372,0.836 0.660,1.037 0.287,0.201 10 SST 1.272,0.934 0.762,0.934 0.762,0.934 1.404,1.392 false

a.

Using SST, remove the 5th driven gear from the output shaft assembly.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03021)
09950-60010  (09951-00180)


Hide 33151D 21.REMOVE REAR BEARING RETAINER

U134456

a.

Remove the 5 bolts and the rear bearing retainer from the manual transmission case.


Hide 33111R 22.REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING

C080351

a.

Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft assembly.


Hide 33311X 23.REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING

C080352

a.

Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft assembly.


Hide 33451H 24.REMOVE REVERSE IDLER GEAR SHAFT BOLT

C067639

a.

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33242E 25.REMOVE SHIFT FORK SHAFT SHAFT SNAP RING

C080353

a.

Using 2 screwdrivers and a hammer, tap out the shift fork shaft shaft snap ring from the No. 2 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



Hide 33275C 26.REMOVE SHIFT DETENT BALL

C067634

a.

Using a hexagon wrench 6 mm, remove the 2 shift detent ball plugs from the manual transmission case.


b.
C067635

Using a magnetic finger, remove the 2 spring seats, compression springs and the 2 shift detent balls from the manual transmission case.


c.
C080354

Using a hexagon wrench 6 mm, remove the shift detent ball plug from the front transaxle case.


d.
C080355

Using a magnetic finger, remove the spring seat, compression spring and the shift detent ball from the front transaxle case.


Hide 27.REMOVE NO. 2 LOCK BALL ASSEMBLY

C080356

a.

Using a hexagon wrench 6 mm, remove the No. 2 lock ball assembly from the manual transmission case.


Hide 33111 28.REMOVE MANUAL TRANSMISSION CASE

C080357

a.

Remove the 3 bolts from the front transaxle case.


b.
C080358

Remove the 13 bolts from the manual transmission case.


c.
C067642

Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the front manual transmission case from the transaxle case.

NOTICE:

Do not damage the manual transmission case and front transaxle case.



Hide 33402 29.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

U158274

a.

Remove the reverse idler gear sub-assembly, reverse idler thrust washer and the reverse idler gear shaft from the front transaxle case.


Hide 33240 30.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

C080360

a.

Remove the 2 bolts and the reverse shift arm bracket assembly from the front transaxle case.


Hide 33243A 31.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C080361

a.

Remove the 2 shift fork set bolts from the No. 2 gear shift fork and the No. 1 gear shift head.


b.
U134457E03
0.365,0.583 1.531,1.292 false 2.594,0.271 2.771,0.448 0.177,0.177 10 false *1 0.188,0.5 0.365,0.677 0.177,0.177 10 false *2

Remove the No. 2 gear shift fork shaft and the No. 1 gear shift head from the front transaxle case.

Text in Illustration
*1 No. 2 Gear Shift Fork Shaft
*2 No. 1 Gear Shift Head


Hide 33242 32.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C080363

a.

Using 2 screwdrivers and a hammer, tap out the snap ring.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C080364E13
1.865,0.677 2.813,0.229 false 2.813,0.125 3,0.302 0.188,0.177 10 false *1

Remove the shift fork set bolt and the No. 1 gear shift fork shaft from the No. 1 gear shift fork.

Text in Illustration
*1 No. 1 Gear Shift Fork Shaft


c.
C080365E16
1.927,1.448 2.531,0.448 false 2.531,0.292 2.75,0.542 0.219,0.25 10 false *1

Remove the No. 1 gear shift fork.

Text in Illustration
*1 No. 1 Gear Shift Fork


Hide 33244G 33.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C080366

a.

Using 2 screwdrivers and a hammer, tap out the snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C080367E12
0.458,0.427 1.354,0.844 false 2.458,0.333 1.969,0.521 false 2.896,1.344 2.26,1.104 false 0.302,0.333 0.479,0.49 0.177,0.156 10 false *1 2.927,1.271 3.104,1.427 0.177,0.156 10 false *3 2.49,0.26 2.667,0.417 0.177,0.156 10 false *2

Remove the No. 3 gear shift fork shaft together with the reverse shift fork and the No. 2 gear shift fork from the front transaxle case.

Text in Illustration
*1 No. 2 Gear Shift Fork
*2 No. 3 Gear Shift Fork Shaft
*3 Reverse Shift Fork


c.
C080368

Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.


d.
C080369

Using 2 screwdrivers and a hammer, tap the snap ring out of the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



e.

Remove the reverse shift fork from the No. 3 gear shift fork shaft.


Hide 34.REMOVE INPUT SHAFT ASSEMBLY

C080586

a.

Remove the input shaft assembly and the output shaft assembly from the front transaxle case.


Hide 35.REMOVE DIFFERENTIAL CASE ASSEMBLY

C067656

a.

Remove the differential case assembly from the front transaxle case.


Hide 33125 36.REMOVE MANUAL TRANSAXLE CASE RECEIVER

C067657

a.

Remove the bolt and the manual transaxle case receiver from the front transaxle case.


Hide 33280 37.REMOVE REVERSE RESTRICT PIN ASSEMBLY

C080372

a.

Using a hexagon wrench 6 mm, remove the reverse restrict pin plug from the manual transmission case.


b.
C080373

Using a pin punch (5 mm) and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.


Hide 33124C 38.REMOVE NO. 1 OIL RECEIVER PIPE

C067644

a.

Remove the bolt and the No. 1 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33124D 39.REMOVE NO. 2 OIL RECEIVER PIPE

C080374

a.

Remove the bolt and the No. 2 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 2 oil receiver pipe.



Hide 33326 40.REMOVE BEARING LOCK PLATE

C067658

a.

Remove the bolt and the bearing lock plate from the front transaxle case.


Hide 33449 41.REMOVE TRANSMISSION MAGNET

U134428E01
2.989,2.011 3.414,2.153 0.425,0.142 3.275,0.152 3.237,0.282 false 2.933,0.411 3.385,0.411 false 2.94,0.457 3.382,0.457 false 3.384,0.618 3.384,0.386 false 2.941,0.516 3.384,0.516 false 2.943,0.553 3.384,0.553 false 2.944,0.609 3.384,0.609 false 2.918,0.4 2.918,0.386 2.918,0.386 3.045,0.386 false 3.224,0.383 3.384,0.383 false 2.94,0.491 3.043,0.491 false 3.241,0.489 3.384,0.489 false 3.241,0.58 3.384,0.58 false 2.942,0.584 3.037,0.584 false

a.

Remove the transmission magnet from the front transaxle case.


Hide 33311A 42.REMOVE INPUT SHAFT FRONT BEARING

C081783E01
0.71,0.957 0.998,1.158 0.287,0.201 10 SST 1.581,1.306 1.077,1.083 false

a.

Using SST, remove the input shaft front bearing from the front transaxle case.

SST
09612-65014  (09612-01050, 09612-01060)


Hide 31105D 43.REMOVE FRONT TRANSAXLE CASE OIL SEAL

C095411

a.

Using a screwdriver, remove the front transaxle case oil seal from the front transaxle case.


Hide 33321N 44.REMOVE OUTPUT SHAFT FRONT BEARING

C082141E01
0.377,0.37 0.664,0.571 0.287,0.201 10 SST 1.528,0.714 0.732,0.479 false

a.

Using SST, remove the output shaft front bearing from the front transaxle case.

SST
09308-00010  

NOTICE:

Do not apply excessive force to the front transaxle case when installing it.



Hide 33134B 45.REMOVE OUTPUT SHAFT COVER

C067719

a.

Remove the output shaft cover from the front transaxle case.


Hide 41311E 46.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C081785E01
0.258,1.713 0.545,1.914 0.287,0.201 10 SST 1.02,1.381 0.607,1.816 false

a.

Using SST, remove the front differential case front tapered roller bearing (outer race) and the front differential case front plate washer from the front transaxle case.

SST
09612-65014  (09612-01040, 09612-01050)


b.
G026414E06
2.073,1.083 2.688,1.521 2.688,1.521 2.125,1.521 false 1.781,1.292 2.656,1.51 false 2.74,1.448 3.031,1.646 0.292,0.198 10 false SST

Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00360)

NOTICE:

Do not damage the bearing.



Hide 31105H 47.REMOVE TRANSAXLE CASE OIL SEAL

C081787E07
1.698,0.854 1.344,1.083 1.344,1.083 1.594,1.458 false 1.031,1 1.323,1.188 0.292,0.188 10 true SST

a.

Using SST and a hammer, remove the transaxle case oil seal from the front transaxle case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)


Hide 41311F 48.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C081788E01
0.769,0.546 1.056,0.747 0.287,0.201 10 SST 1.115,1.142 0.936,0.778 false

a.

Using SST, remove the front differential case rear tapered roller bearing (outer race) and the front differential case rear plate washer from the manual transmission case.

SST
09612-65014  (09612-01040, 09612-01050)


b.
C082144E04
2.448,1.49 2.729,1.698 2.729,1.698 1.813,1.469 false 2.781,1.625 3.073,1.823 0.292,0.198 10 false SST

Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

NOTICE:

Do not damage the bearing.



Hide 33111Q 49.REMOVE TRANSMISSION CASE OIL SEAL

C081789E01
0.829,0.192 1.116,0.392 0.287,0.201 10 SST 1.712,0.54 1.199,0.343 1.199,0.343 1.586,1.431 false

a.

Using SST and a hammer, drive out the transmission case oil seal from the manual transmission case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)


Hide 33261H 50.REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL

C121110

a.

Using a screwdriver and hammer, remove the shift and select lever shaft oil seal.


Hide 33261K 51.REMOVE SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING

C121111E03
1.219,1.073 2.458,0.979 2.458,0.979 1.75,0.844 true 2.521,0.906 2.896,1.104 0.375,0.198 10 false SST

a.

Using SST and a hammer, remove the shift and select lever shaft slide ball bearing.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07200)