Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248200 MANUAL TRANSAXLE UNIT A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 33134B 1.INSTALL OUTPUT SHAFT COVER

C095191E09
1.458,0.125 1.75,0.365 false 2.49,0.125 2.781,0.365 false 1.281,0.021 1.458,0.198 0.177,0.177 10 false *1 2.292,0.021 2.458,0.198 0.167,0.177 10 false *2

a.

Coat the output shaft cover with MP grease and install it onto the front transaxle case.

Text in Illustration
*1 Front Transaxle Case
*2 Output Shaft Cover

NOTICE:

Insert the output shaft cover projection into the case side hollow.



Hide 33321N 2.INSTALL OUTPUT SHAFT FRONT BEARING

C080376E01
0.576,0.309 0.863,0.510 0.287,0.201 10 SST 1.238,0.498 0.954,0.43 0.954,0.43 1.169,1.031 false

a.

Coat a new output shaft front bearing with gear oil. Using SST and a press, install it onto the front transaxle case.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07150)

NOTICE:
·

Install the new bearing in the correct direction as shown in the illustration.

·

When replacing the output shaft front bearing, replace the output shaft front bearing inner race at the same time.




Hide 31105D 3.INSTALL FRONT TRANSAXLE CASE OIL SEAL

C081790E01
0.36,0.373 0.647,0.574 0.287,0.201 10 SST 1.209,0.795 0.734,0.549 0.734,0.549 1.161,1.555 false

a.

Using SST and a hammer, install a new front transaxle case oil seal onto the front transaxle case.

SST
09950-60010  (09951-00370)
09950-70010  (09951-07150)

Drive in depth:

15.6 to 16.0 mm (0.614 to 0.630 in.)



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33311A 4.INSTALL INPUT SHAFT FRONT BEARING

C081791E01
0.286,0.265 0.573,0.466 0.287,0.201 10 SST 0.863,0.498 0.658,0.414 0.658,0.414 0.833,0.895 false

a.

Coat a new input shaft front bearing with gear oil, and using SST and a press, install it onto the front transaxle case.

SST
09950-60010  (09951-00420)
09950-70010  (09951-07150)

Drive in depth:

0 to 0.3 mm (0 to 0.0118 in.)



Hide 33261K 5.INSTALL SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING

C121112E01
1.094,1.438 0.479,1.604 0.479,1.604 1.104,1.26 true 0.115,1.531 0.438,1.719 0.323,0.188 10 false SST

a.

Using SST and a hammer, install the shift and select lever shaft slide ball bearing onto the manual transmission case.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Drive in depth:

0 to 0.5 mm (0 to 0.00197 in.)



Hide 33261H 6.INSTALL SHIFT AND SELECT LEVER SHAFT OIL SEAL

C120752E01
2.406,0.458 2.802,0.219 false 2.854,0.115 3.188,0.281 0.333,0.167 10 false SST

a.

Using SST, install the shift and select lever shaft oil seal onto the manual transmission case.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00240)

Drive in depth:

9.7 to 10.3 mm (0.382 to 0.406 in.)



Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C082146E01
2.241,0.298 2.528,0.499 0.287,0.201 10 SST 1.789,0.339 2.211,0.404 2.211,0.404 1.906,0.605 false

a.

Using SST and a press, install the front differential case front tapered roller bearing (inner race) onto the differential case assembly.

SST
09350-32014  (09351-32120)
09950-60010  (09951-00530)


b.
C080379E01
2.125,0.471 2.412,0.672 0.287,0.201 10 SST 1.839,0.848 2.273,0.673 2.273,0.673 2.006,1.081 false

Using SST and a press, install the front differential case front tapered roller bearing (outer race) together with the front differential case front plate washer onto the front transaxle case.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)


Hide 41311F 8.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C082147E01
2.394,0.105 2.681,0.306 0.287,0.201 10 SST 1.866,0.315 2.345,0.223 2.345,0.223 1.982,0.587 false

a.

Using SST and a press, install the front differential case rear tapered roller bearing (inner race) onto the differential case assembly.

SST
09350-32014  (09351-32120)
09950-60010  (09951-00530)


b.
C081792E01
2.902,0.339 3.189,0.540 0.287,0.201 10 SST 2.012,0.582 2.833,0.488 2.833,0.488 2.079,1.558 false 2.133,0.885 2.833,0.488 false

Using SST and a press, install the front differential case rear tapered roller bearing (outer race) with front differential case rear plate washer onto the manual transmission case.

SST
09309-36010  
09950-60020  (09951-00710)
09950-70010  (09951-07150)

HINT:

Use a plate washer of the same thickness as the removed one.



Hide 9.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

C067656

a.

Coat the differential case assembly with gear oil, and install it onto the front transaxle case.


b.

Install the manual transmission case with the 16 bolts.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C081793E01
1.099,0.167 1.387,0.368 0.287,0.201 10 SST 0.994,1.291 1.251,0.391 false

Using SST and a torque wrench, turn the differential case assembly to the right and left 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


d.
C081793E01
1.099,0.167 1.387,0.368 0.287,0.201 10 SST 0.994,1.291 1.251,0.391 false

Using SST and a torque wrench, measure the preload.

SST
09564-32011  

Preload (at starting):
New bearing:

0.78 to 1.57 N*m (8.0 to 16.0 kgf*cm, 7.0 to 13.8 in.*lbf)

Used bearing:

0.49 to 0.98 N*m (5.0 to 9.0 kgf*cm, 4.4 to 8.6 in.*lbf)


If the preload is outside the specifications, select another plate washer.

Plate Washer Thickness:
Part No. Mark Thickness mm (in.)
90564-41014 AA 2.10 (0.0827)
90564-41015 BB 2.15 (0.0846)
90564-41016 CC 2.20 (0.0866)
90564-41017 DD 2.25 (0.0886)
90564-41018 EE 2.30 (0.0906)
90564-41019 FF 2.35 (0.0925)
90564-41020 GG 2.40 (0.0945)
90564-41021 HH 2.45 (0.0965)
90564-41022 JJ 2.50 (0.0984)
90564-41023 KK 2.55 (0.1004)
90564-41024 LL 2.60 (0.1024)
90564-41025 MM 2.65 (0.1043)
90564-41026 NN 2.70 (0.1063)
90564-41027 PP 2.75 (0.1083)
90564-41028 QQ 2.80 (0.1102)
90564-41029 RR 2.85 (0.1122)
90564-41030 SS 2.90 (0.1142)
90564-41031 TT 2.95 (0.1161)
90564-41032 UU 3.00 (0.1181)


HINT:

The preload changes by approximately 0.3 to 0.4 N*m (3.1 to 4.0 kgf*cm, 2.7 to 3.5 in.*lbf) per each 0.05 mm (0.00197 in.) change in plate washer thickness.



e.

Remove the 16 bolts and the manual transmission case.


f.

Remove the differential case assembly from the front transaxle case.


Hide 33111Q 10.INSTALL TRANSMISSION CASE OIL SEAL

C080381E01
0.952,0.07 1.240,0.271 0.287,0.201 10 SST 1.327,0.172 1.942,0.176 false

a.

Using SST and a hammer, install a new transmission case oil seal onto the manual transmission case.

SST
09316-60011  (09316-00011)

Drive in depth:

9.4 to 10.4 mm (0.370 to 0.409 in.)



b.

Coat the lip of the front transmission case oil seal with MP grease.


Hide 31105H 11.INSTALL TRANSAXLE CASE OIL SEAL

C080382E01
1.335,0.338 1.622,0.539 0.287,0.201 10 SST 1.874,0.461 1.72,0.461 1.72,0.461 1.79,1.021 false

a.

Using SST and a hammer, install a new transaxle case oil seal onto the front transaxle case.

Drive in depth:

1.4 to 2.0 mm (0.0551 to 0.0787 in.)


SST
09710-20011  (09710-06071)
09950-70010  (09951-07150)


b.

Coat the lip of the transaxle case oil seal with MP grease.


Hide 33449 12.INSTALL TRANSMISSION MAGNET

C355427

a.

Clean the transmission magnet and install it onto the front transaxle case.


Hide 33326 13.INSTALL BEARING LOCK PLATE

C067658

a.

Install the bearing lock plate onto the front transaxle case with the bolt.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 33124C 14.INSTALL NO. 1 OIL RECEIVER PIPE

C068380

a.

Install the No. 1 oil receiver pipe onto the manual transmission case with the bolt.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Do not deform the No. 1 oil receiver pipe.

·

Install the No. 1 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.




Hide 33124D 15.INSTALL NO. 2 OIL RECEIVER PIPE

C080432

a.

Install the No. 2 oil receiver pipe onto the manual transmission case with the bolt.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Do not deform the No. 2 oil receiver pipe.

·

Install the No. 2 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.




Hide 33280 16.INSTALL REVERSE RESTRICT PIN ASSEMBLY

C080383

a.

Install the reverse restrict pin assembly onto the manual transmission case.

NOTICE:

Set the reverse restrict pin assembly in the correct orientation.



b.
C080384

Using a pin punch (5 mm) and a hammer, install the slotted spring pin onto the reverse restrict pin assembly.

Drive in depth:

15.5 to 16.5 mm (0.611 to 0.650 in.)



c.
C120732

Apply adhesive to the reverse restrict pin plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



d.

Using a hexagon wrench 6 mm and a torque wrench, install the reverse restrict pin plug onto the manual transmission case.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 33125 17.INSTALL MANUAL TRANSAXLE CASE RECEIVER

C067657

a.

Install the manual transaxle case receiver onto the front transaxle case with the bolt.

Torque:
11 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 18.INSTALL DIFFERENTIAL CASE ASSEMBLY

C067656

a.

Coat the differential case tapered roller bearing with gear oil and install the differential case assembly onto the front transaxle case.

NOTICE:

Do not damage the tapered roller bearing.



Hide 19.INSTALL INPUT SHAFT ASSEMBLY

C080586

a.

Coat the sliding and rotating surfaces of the input shaft assembly and the output shaft assembly with gear oil and install them onto the front transaxle case.

NOTICE:

Do not damage the oil seal.



Hide 33402 20.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

C080386

a.

Coat the reverse idler gear sub-assembly, reverse idler thrust washer and the reverse idler gear shaft with gear oil and install them as shown in the illustration.

Text in Illustration
V100135

Align Alignment Mark

HINT:

Align the mark on the reverse idler gear shaft with the bolt hole shown in the illustration.



Hide 33242 21.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
C080387E13
2.125,0.667 2.604,0.417 false 1.938,1.688 2.99,1.292 false 3.042,1.188 3.219,1.333 0.177,0.146 10 false *1 2.646,0.313 3.021,0.51 0.375,0.198 10 false *2

Coat the No. 1 gear shift fork and the No. 2 gear shift fork with gear oil and install them.

Text in Illustration
*1 No. 1 Gear Shift Fork
*2 No. 2 Gear Shift Fork


b.
C080388E13
1.917,1.042 2.854,0.521 false 2.885,0.375 3.073,0.552 0.188,0.177 10 false *1

Coat the No. 1 gear shift fork shaft with gear oil and install it.

Text in Illustration
*1 No. 1 Gear Shift Fork Shaft


c.

Install a new shift fork set bolt.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


d.
C080389

Using a brass bar and a hammer, install a new snap ring onto the No. 1 gear shift fork shaft.


Hide 33244G 22.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

C080450

a.

Coat the 2 reverse shift fork balls with MP grease and install them onto the reverse shift fork.


b.

Install the reverse shift fork onto the No. 3 gear shift fork shaft .


c.
C080391

Using a brass bar and a hammer, install 2 new snap rings onto the No. 3 gear shift fork shaft.


d.
C080392

Coat the No. 3 gear shift fork shaft with gear oil and install it.


Hide 33243A 23.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

C117123

a.

Coat the No. 1 gear shift head and the No. 2 gear shift fork shaft with gear oil and install them.

NOTICE:

To avoid interference by the 2 shift fork balls, lift up the No. 3 gear shift fork shaft to the position shown in the illustration.



b.
C080361

Install 2 new shift fork set bolts to the No. 2 gear shift fork and the No. 1 gear shift head.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 33240 24.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

C080360

a.

Install the reverse shift arm bracket assembly onto the front transaxle case with 2 bolts.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 33111 25.INSTALL MANUAL TRANSMISSION CASE

C082142E07
2.614,0.078 3.019,0.279 0.406,0.201 10 *a 2.325,0.563 2.576,0.232 false

a.

Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the manual transmission case as shown in the illustration.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
C080358

Install the 13 bolts onto the manual transmission case side.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C080357

Install the 3 bolts onto the front transaxle case side.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33451H 26.INSTALL REVERSE IDLER GEAR SHAFT BOLT

C067639

a.

Coat the reverse idler gear shaft bolt with adhesive and install it with a new gasket.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 27.INSTALL NO. 2 LOCK BALL ASSEMBLY

C080356

a.

Coat the No. 2 lock ball assembly with adhesive and install it with a hexagon wrench 6 mm .

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33275C 28.INSTALL SHIFT DETENT BALL

D032759

a.

Install the 2 shift detent balls, 2 compression springs and the 2 spring seats onto the manual transmission case.


b.
C067634

Coat the 2 shift detent ball plugs with adhesive and install them using a hexagon wrench 6 mm .

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


c.
C080393

Install the shift detent ball, compression spring and the spring seat onto the front transaxle case.


d.
C080354

Coat the shift detent ball plug with adhesive and install it using a hexagon wrench 6 mm .

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 33311X 29.INSTALL INPUT SHAFT REAR BEARING HOLE SNAP RING

C080352

a.

Using a snap ring expander, install the input shaft rear bearing hole snap ring onto the input shaft assembly.


Hide 33111R 30.INSTALL OUTPUT SHAFT REAR BEARING HOLE SNAP RING

C080351

a.

Using a snap ring expander, install the output shaft rear bearing hole snap ring onto the output shaft assembly.


Hide 33242E 31.INSTALL SHIFT FORK SHAFT SHAFT SNAP RING

C080394

a.

Using a brass bar and a hammer, install a new shift fork shaft shaft snap ring onto the No. 2 gear shift fork shaft.


Hide 33151D 32.INSTALL REAR BEARING RETAINER

U134456

a.

Install the rear bearing retainer onto the manual transmission case with 5 new bolts.

Torque:
27 N*m (280 kgf*cm, 20 ft.*lbf)


Hide 33428C 33.INSTALL 5TH DRIVEN GEAR

C095786E10
0.844,1.198 1.031,1.26 0.188,0.063 0.823,1.125 0.958,1.063 false 0.99,0.948 1.313,1.115 0.323,0.167 10 false SST 1.406,0.729 1.719,0.896 0.313,0.167 10 false SST

a.

Using SST, install the 5th driven gear onto the output shaft assembly.

SST
09309-12020  


Hide 33336A 34.INSTALL 5TH GEAR NEEDLE ROLLER BEARING

U158273

a.

Coat the 5th gear needle roller bearing and the 5th gear bearing spacer with gear oil, and install them onto the input shaft assembly.


Hide 33336 35.INSTALL 5TH GEAR

C080396

a.

Coat the 5th gear with gear oil and install it onto the input shaft assembly.


Hide 33369 36.INSTALL NO. 3 SYNCHRONIZER RING

D031112

a.

Coat the No. 3 synchronizer ring with gear oil and install it onto the 5th gear.


Hide 33393 37.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
C355428

Install the 3 synchromesh shifting keys and the 2 synchromesh shifting key springs onto the No. 3 transmission clutch hub as shown in the illustration.

Text in Illustration
V100135

Engine Side

NOTICE:

Do not set the 2 shifting key spring openings in the same position.



b.
C355262E01
2.313,4.031 1.938,4.198 false 1.135,0.948 1.198,0.719 false 1.76,4.135 2.073,4.333 0.313,0.198 10 false *1 2.229,1.698 2.542,1.896 0.313,0.198 10 false *a 1.083,0.563 1.542,0.76 0.458,0.198 10 false SST

Using SST and a hammer, install the No. 3 transmission clutch hub onto the input shaft assembly.

SST
09636-20010  

Text in Illustration
*1 Wooden Block
*a Key Position

NOTICE:
·

Do not install the No. 3 transmission clutch hub in the wrong direction.

·

Install the No. 3 transmission clutch hub with the No. 3 synchronizer ring key groove and the No. 3 synchromesh shifting key aligned.

·

Check that the 5th gear is rotating.

·

Place a suitable sized wooden block to support the input shaft.




c.
C080400

Select a No. 3 clutch hub shaft snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.00394 in.) or less


Snap Ring Thickness:
Part No. Mark Thickness mm (in.)
90520-18002 A 2.25 (0.0886)
90520-18003 B 2.31 (0.0909)
90520-18004 C 2.37 (0.0933)
90520-18006 D 2.43 (0.0957)
90520-18007 E 2.49 (0.0980)
90520-18008 F 2.55 (0.1004)
90520-18009 G 2.61 (0.1028)



d.

Using a brass bar and a hammer, install the No. 3 clutch hub shaft snap ring onto the input shaft assembly.


Hide 33336 38.INSPECT 5TH GEAR THRUST CLEARANCE

C080344

a.

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.1 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, the 5th gear or input shaft rear radial ball bearing.


Hide 33336 39.INSPECT 5TH GEAR RADIAL CLEARANCE

C080345

a.

Using a dial indicator, measure 5th gear radial clearance.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


Hide 33214G 40.INSTALL NO. 3 GEAR SHIFT FORK

C080401

a.

Coat the No. 3 transmission hub sleeve with gear oil and install it together with the No. 3 gear shift fork onto the No. 3 transmission clutch hub.

HINT:

Set the No. 3 transmission clutch hub in the correct orientation.



b.
C080402

Install a new shift fork set bolt onto the No. 3 gear shift fork.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 33321G 41.INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

C080403

a.

Engage the 2 gears simultaneously to lock the transmission.


b.

Install a new manual transmission output shaft rear set nut.

Torque:
118 N*m (1200 kgf*cm, 87 ft.*lbf)


c.
C080404

Using a chisel and a hammer, stake the manual transmission output shaft rear set nut.


d.

Disengage the 2 gears.


Hide 33102 42.INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

a.
C080556E12
1.094,0.521 0.625,0.302 false 0.396,0.177 0.573,0.375 0.177,0.198 10 false *a

Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the manual transaxle case cover sub-assembly as shown in the illustration.

Text in Illustration
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.




b.
A057108

Apply adhesive to 2 or 3 threads on the end of the 9 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.
C080554

Install the manual transmission case cover sub-assembly onto the manual transmission case with the 9 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 43.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

C120740

a.

Coat the shift and select lever shaft assembly with gear oil, and install it onto the manual transmission case.


Hide 33528C 44.INSTALL CONTROL SHAFT COVER OIL SEAL

C120731E01
2.365,1.229 2.01,1.406 true 1.958,1.25 2.365,1.229 false 2.417,1.135 2.74,1.313 0.323,0.177 10 false SST

a.

Using SST and a hammer, install a new control shaft cover oil seal onto the control shaft cover.

Drive in depth:

0.2 to 1.2 mm (0.00787 to 0.0472 in.)


SST
09950-60010  (09951-00280)
09950-70010  (09951-07150)


b.

Coat the control shaft cover oil seal with MP grease.


Hide 33528B 45.INSTALL CONTROL SHAFT COVER

C120742

a.

Coat the 4 bolts with adhesive.


b.

Install a new gasket and the control shaft cover onto the manual transmission case with the 4 bolts.

Torque:
20 N*m (200 kgf*cm, 14 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Set the claws of the shift interlock plate into the shift head part of the gear shift fork shaft securely.



Hide 33295A 46.INSTALL SHIFT GATE PIN

C120743

a.

Coat the shift gate pin with adhesive.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.

Install the washer and the shift gate pin.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 33290 47.INSTALL NO. 1 LOCK BALL ASSEMBLY

C120744

a.

Coat the No. 1 lock ball assembly with adhesive, install it onto the manual transmission case.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



Hide 33544C 48.INSTALL SHIFT LEVER DAMPER

C120746

a.

Install the dust boot onto the control shaft cover.


b.

Install the shift lever damper with the lock pin onto the shift and select lever shaft assembly.


c.

Install the spring washer with the nut.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33527 49.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER

C120748

a.

Install the dust boot onto the shift and select lever shaft oil seal.


b.

Install the floor shift control shift lever with the lock pin onto the shift and select lever shaft assembly.


c.

Install the spring washer with the nut.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 50.INSTALL SELECTING BELL CRANK ASSEMBLY

C120750

a.

Install the selecting bell crank assembly together with the control bell crank dust cover onto the manual transmission case with the 2 bolts and nut.

Torque:
for Bolt : 25 N*m (250 kgf*cm, 18 ft.*lbf)
for Nut : 12 N*m (120 kgf*cm, 9 ft.*lbf)

NOTICE:

Apply MP grease to the inside circumferential surface of the control bell crank dust cover.



Hide 84210 51.INSTALL BACK UP LIGHT SWITCH ASSEMBLY

C120749E01
1.504,1.722 1.857,1.897 0.353,0.175 10 SST 2.092,1.28 1.668,1.704 false

a.

Using SST, install the back up light switch assembly onto the manual transmission case with a new gasket.

SST
09817-16011  

Torque:
40 N*m (410 kgf*cm, 30 ft.*lbf)


b.

Install the back up light switch wire harness into the 2 clamps.


Hide 33101A 52.INSTALL MANUAL TRANSMISSION FILLER PLUG

C080549

a.

Install the manual transmission filler plug onto the manual transmission case with a new gasket.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33104 53.INSTALL DRAIN PLUG SUB-ASSEMBLY

C080550

a.

Install the drain plug sub-assembly onto the manual transmission case with a new gasket.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)