Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › INPUT SHAFT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248201 INPUT SHAFT G

C54 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  INSPECTION  


PROCEDURE

Hide 33311 1.INSPECT INPUT SHAFT

CM00013

a.

Using a dial indicator, check the input shaft runout.

Maximum runout:

0.015 mm (0.000591 in.)


If the runout exceeds the maximum, replace the input shaft.


b.
C355266E01
0.479,3.521 0.479,3.135 false 0.958,3.49 0.958,3.104 false 1.406,3.479 1.406,3.094 false 2.396,3.5 2.396,3.115 false 0.438,2.948 0.594,3.146 0.156,0.198 10 false A 0.917,2.938 1.073,3.135 0.156,0.198 10 false B 1.365,2.927 1.521,3.125 0.156,0.198 10 false C 2.354,2.948 2.51,3.146 0.156,0.198 10 false D

Using a micrometer, measure the outer diameter of the input shaft journal surface, at the locations indicated.

Standard outer diameter:
Part A:

24.885 to 24.900 mm (0.9797 to 0.9803 in.)

Part B:

28.991 to 29.006 mm (1.1414 to 1.1420 in.)

Part C:

30.985 to 31.000 mm (1.2199 to 1.2205 in.)

Part D:

24.985 to 25.000 mm (0.9837 to 0.9843 in.)


Minimum outer diameter:
Part A:

24.885 mm (0.9797 in.)

Part B:

28.991 mm (1.1414 in.)

Part C:

30.985 mm (1.2199 in.)

Part D:

24.985 mm (0.9837 in.)


If the outer diameters are less than the minimums, replace the input shaft.


Hide 33334 2.INSPECT 4TH GEAR

C067826

a.

Using a cylinder gauge, measure the inside diameter of the 4th gear.

Standard inside diameter:

34.015 to 34.031 mm (1.3392 to 1.3398 in.)


Maximum inside diameter:

34.031 mm (1.3398 in.)


If the inside diameter exceeds the maximum, replace the 4th gear.


Hide 33333 3.INSPECT 3RD GEAR

C067827

a.

Using a cylinder gauge, measure the inside diameter of the 3rd gear.

Standard inside diameter:

36.015 to 36.031 mm (1.4179 to 1.4185 in.)


Maximum inside diameter:

36.031 mm (1.4185 in.)


If the inside diameter exceeds the maximum, replace the 3rd gear.


Hide 33368H 4.INSPECT 4TH GEAR SYNCHRONIZER RING

C080457

a.

Check for wear and damage.


b.

Coat the 4th gear cone with gear oil.


c.

Turn the synchronizer ring in one direction while pushing it against the 4th gear cone.


d.

Check that the ring locks.

If the 4th gear synchronizer outer ring does not lock, replace the synchronizer ring.


e.
C080458

Using a feeler gauge, measure the clearance between the synchronizer ring back and the gear spline end.

Standard clearance:

0.75 to 1.65 mm (0.0295 to 0.0650 in.)


Minimum clearance:

0.75 mm (0.0295 in.)


If the clearance is less than the minimum, replace the 4th gear synchronizer ring.


Hide 33368G 5.INSPECT 3RD GEAR SYNCHRONIZER RING

C080459

a.

Check for wear and damage.


b.

Coat the 3rd gear cone with gear oil.


c.

Turn the synchronizer ring in one direction while pushing it against the 3rd gear cone.


d.

Check that the ring locks.

If the 3rd gear synchronizer outer ring does not lock, replace the synchronizer ring.


e.
C080460

Using a feeler gauge, measure the clearance between the synchronizer ring back and the gear spline end.

Standard clearance:

0.75 to 1.65 mm (0.0295 to 0.0650 in.)


Minimum clearance:

0.75 mm (0.0295 in.)


If the clearance is less than the minimum, replace the 3rd gear synchronizer ring.


Hide 33364 6.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

C067843

a.

Check the sliding condition between the No. 2 transmission hub sleeve and the No. 2 transmission clutch hub.


b.

Check that the edges of the No. 2 transmission hub sleeve spline gear are not worn down.


c.
C355268E01
0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.896,2 1.052,2.198 0.156,0.198 10 false A 2.771,3.24 2.927,3.438 0.156,0.198 10 false B

Using a vernier caliper, measure the width of the No. 2 transmission hub sleeve groove (B) and the thickness of the claw part on the No. 2 gear shift fork (A), and calculate the clearance.

Text in Illustration
*a Clearance = (B - A)

Standard clearance (B - A):

0.15 to 0.35 mm (0.00591 to 0.0138 in.)


If the clearance is outside the specifications, replace the No. 2 transmission hub sleeve and the No. 2 gear shift fork.