Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › INPUT SHAFT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248201 INPUT SHAFT A

C54 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33334 1.INSPECT 4TH GEAR THRUST CLEARANCE

C080557

a.

Using a feeler gauge, measure the 4th gear thrust clearance.

Standard clearance:

0.1 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft rear radial ball bearing.


Hide 33333 2.INSPECT 3RD GEAR THRUST CLEARANCE

C067816

a.

Using a dial indicator, measure the 3rd gear thrust clearance.

Standard clearance:

0.1 to 0.35 mm (0.00394 to 0.0138 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


Hide 33334 3.INSPECT 4TH GEAR RADIAL CLEARANCE

C080558

a.

Using a dial indicator, measure the 4th gear radial clearance between the 4th gear and input shaft.

Standard clearance:

0.009 to 0.050 mm (0.000354 to 0.00197 in.)


Maximum clearance:

0.050 mm (0.00197 in.)


If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


Hide 33333 4.INSPECT 3RD GEAR RADIAL CLEARANCE

C067815

a.

Using a dial indicator, measure the 3rd gear radial clearance between the 3rd gear and input shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


Hide 33334 5.REMOVE 4TH GEAR

C080559

a.

Using 2 screwdrivers and a hammer, remove the input shaft rear bearing shaft snap ring from the input shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
Q004983E01
2.747,0.577 3.034,0.778 0.287,0.201 10 SST

Using SST and a press, remove the input shaft rear radial ball bearing and the 4th gear from the input shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft assembly by hand to prevent it from dropping off.




Hide 33334A 6.REMOVE 4TH GEAR NEEDLE ROLLER BEARING

U158275

a.

Remove the 4th gear needle roller bearing and the 4th gear bearing spacer from the input shaft.


Hide 33368H 7.REMOVE 4TH GEAR SYNCHRONIZER RING

U158276

a.

Remove the 4th gear synchronizer ring from the No. 2 transmission clutch hub.


Hide 33333 8.REMOVE 3RD GEAR

C067821

a.

Using 2 screwdrivers and a hammer, remove the snap ring from the input shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
CM00064E01
0.524,0.49 0.811,0.691 0.287,0.201 10 SST

Using SST and a press, remove the No. 2 transmission clutch hub and the 3rd gear from the input shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand to prevent it from dropping off.




Hide 33368G 9.REMOVE 3RD GEAR SYNCHRONIZER RING

C080455

a.

Remove the 3rd gear synchronizer ring from the 3rd gear.


Hide 33333A 10.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

U158271

a.

Remove the 3rd gear needle roller bearing from the input shaft.


Hide 33364 11.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

C067832

a.

Remove the No. 2 transmission hub sleeve, the 3 synchromesh shifting keys and the 3 synchromesh shifting key springs from the No. 2 transmission clutch hub.

HINT:

Use a piece of cloth to keep the synchromesh shifting key and synchromesh shifting key spring from flying off.