Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › INPUT SHAFT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248201 INPUT SHAFT A

C54 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33364 1.INSTALL NO. 2 TRANSMISSION HUB SLEEVE

C069660

a.

Coat the No. 2 transmission hub sleeve with gear oil, and install it to the No. 2 transmission clutch hub.

NOTICE:

Orient the No. 2 transmission hub sleeve and the No. 2 transmission clutch hub correctly.



b.

Using a screwdriver, install the 3 synchromesh shifting key springs with the 3 synchromesh shifting keys onto the No. 2 transmission clutch hub.


Hide 33333A 2.INSTALL 3RD GEAR NEEDLE ROLLER BEARING

U158271

a.

Coat the 3rd gear needle roller bearing with gear oil and install it onto the input shaft.


Hide 33333 3.INSTALL 3RD GEAR

U158517

a.

Coat the 3rd gear with gear oil and install it onto the input shaft.


Hide 33368G 4.INSTALL 3RD GEAR SYNCHRONIZER RING

D031159E11
2.156,0.26 3.104,0.458 0.948,0.198 10 false *a 2.521,1.292 2.688,1.49 0.167,0.198 10 false *b

a.

Coat the 3rd gear synchronizer ring with gear oil and install it onto the 3rd gear.

Text in Illustration
*a Key Position
*b for 3rd Gear


Hide 33362 5.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

C080563E01
2.197,1.378 2.484,1.579 0.287,0.201 10 SST 1.416,1.475 2.152,1.495 false

a.

Using SST and a press, install the No. 2 transmission clutch hub onto the input shaft.

SST
09316-60011  (09316-00021)

NOTICE:

Fit the synchromesh shifting key into the groove of the synchronizer ring correctly.



b.
C067837

Select a snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.00394 in.) or less.


Snap Ring Thickness:
Part No. Mark Thickness mm (in.)
90520-27046 0 2.30 (0.0906)
90520-27047 1 2.36 (0.0929)
90520-27048 2 2.42 (0.0953)
90520-27049 3 2.48 (0.0976)
90520-27050 4 2.54 (0.1000)
90520-27051 5 2.60 (0.1024)



c.

Using a brass bar and a hammer, install the snap ring onto the input shaft.


Hide 33368H 6.INSTALL 4TH GEAR SYNCHRONIZER RING

a.
C080464E11
2.24,0.375 3.188,0.573 0.948,0.198 10 false *a 2.677,1.354 2.875,1.552 0.198,0.198 10 false *b

Coat the 4th gear synchronizer ring with gear oil and install it onto the No. 2 transmission clutch hub.

Text in Illustration
*a Key Position
*b for 4th Gear


Hide 33334A 7.INSTALL 4TH GEAR NEEDLE ROLLER BEARING

U158275

a.

Coat the 4th gear needle roller bearing and the 4th gear bearing spacer with gear oil and install them onto the No. 2 transmission clutch hub.


Hide 33334 8.INSTALL 4TH GEAR

U158277

a.

Coat the 4th gear with gear oil and install it onto the input shaft.


Hide 33311E 9.INSTALL INPUT SHAFT REAR RADIAL BALL BEARING

C080565E01
2.624,0.057 2.911,0.258 0.287,0.201 10 SST 2.572,0.155 1.908,0.132 false

a.

Using SST and a press, install the input shaft rear radial ball bearing onto the input shaft.

SST
09608-04031  


b.
C080566

Select a snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.00394 in.) or less


Snap Ring Thickness:
Part No. Mark Thickness mm (in.)
90520-22006 A 2.29 (0.0902)
90520-22007 B 2.35 (0.0925)
90520-22008 C 2.41 (0.0949)
90520-22009 D 2.47 (0.0972)
90520-22010 E 2.53 (0.0996)
90520-22011 F 2.59 (0.1020)



c.

Using a brass bar and a hammer, install the snap ring onto the input shaft.

NOTICE:

Do not damage the journal surface of the snap ring.



Hide 33333 10.INSPECT 3RD GEAR RADIAL CLEARANCE

C067815

a.

Using a dial indicator, measure the 3rd gear radial clearance between the 3rd gear and input shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


Hide 33334 11.INSPECT 4TH GEAR RADIAL CLEARANCE

C080558

a.

Using a dial indicator, measure the 4th gear radial clearance between the 4th gear and input shaft.

Standard clearance:

0.009 to 0.050 mm (0.000354 to 0.00197 in.)


Maximum clearance:

0.050 mm (0.00197 in.)


If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


Hide 33333 12.INSPECT 3RD GEAR THRUST CLEARANCE

C067816

a.

Using a dial indicator, measure the 3rd gear thrust clearance.

Standard clearance:

0.1 to 0.35 mm (0.00394 to 0.0138 in.)


Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


Hide 33334 13.INSPECT 4TH GEAR THRUST CLEARANCE

C080557

a.

Using a feeler gauge, measure the 4th gear thrust clearance.

Standard clearance:

0.1 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft rear radial ball bearing.