Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248202 OUTPUT SHAFT A

C54 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33335 1.INSPECT 1ST GEAR THRUST CLEARANCE

C080538

a.

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard clearance:

0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum clearance:

0.40 mm (0.0157 in.)


If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear, or No. 1 transmission clutch hub.


Hide 33332 2.INSPECT 2ND GEAR THRUST CLEARANCE

C068312

a.

Using a dial indicator, measure the 2nd gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear, or 3rd driven gear.


Hide 33335 3.INSPECT 1ST GEAR RADIAL CLEARANCE

C068309

a.

Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 1st gear or 1st gear needle roller bearing.


Hide 33332 4.INSPECT 2ND GEAR RADIAL CLEARANCE

C068254

a.

Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 2nd gear or 2nd gear needle roller bearing.


Hide 33422B 5.REMOVE 4TH DRIVEN GEAR

C080539E07
0.635,1 0.521,0.313 false 0.135,0.156 0.479,0.354 0.344,0.198 10 false SST

a.

Using SST and a press, remove the output shaft rear bearing and the 4th driven gear from the output shaft.

SST
09950-00020  


Hide 33431C 6.REMOVE OUTPUT GEAR SPACER

C068005

a.

Remove the output gear spacer from the output shaft.


Hide 33332 7.REMOVE 2ND GEAR

G027264E07
0.844,0.667 0.563,0.396 false 0.188,0.292 0.531,0.49 0.344,0.198 10 false SST

a.

Using SST and a press, remove the 3rd driven gear with the 2nd gear from the output shaft.

SST
09950-00020  


Hide 33332B 8.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.
C080541

Remove the 2nd gear needle roller bearing and the 2nd gear bearing spacer from the output shaft.


Hide 33367 9.REMOVE NO. 1 SYNCHRONIZER RING (FOR 2ND GEAR)

C120730

a.

Remove the No. 1 synchronizer ring from the output shaft.


Hide 33335 10.REMOVE 1ST GEAR

C080543

a.

Using 2 screwdrivers and a hammer, remove the snap ring from the output shaft.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C080544E08
0.771,0.667 0.563,0.333 false 0.156,0.229 0.5,0.427 0.344,0.198 10 false SST

Using SST and a press, remove the No. 1 transmission clutch hub assembly and the 1st gear from the output shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand to prevent it from dropping off.




Hide 33367 11.REMOVE NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR)

a.
C080465

Remove the No. 1 synchronizer ring from the 1st gear.


Hide 33335C 12.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

C068012

a.

Remove the 1st gear needle roller bearing from the output shaft.


Hide 33348 13.REMOVE 1ST GEAR THRUST WASHER

C068013

a.

Remove the 1st gear thrust washer from the output shaft.


Hide 33348A 14.REMOVE 1ST GEAR THRUST WASHER PIN OR BALL

C068014

a.

Remove the 1st gear thrust washer pin or ball from the output shaft.


Hide 33331 15.REMOVE REVERSE GEAR

C068015

a.

Remove the reverse gear, 3 synchromesh shifting keys and the 3 synchromesh shifting key springs from the No. 1 transmission clutch hub.

HINT:

Use a piece of cloth to keep the synchromesh shifting key and synchromesh shifting key spring from flying off.