Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM19S0E _52 Drivetrain _051468 C54 MANUAL TRANSMISSION / TRANSAXLE _0248202 OUTPUT SHAFT A

C54 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33331 1.INSTALL REVERSE GEAR

C068241

a.

Coat the reverse gear with gear oil and install it onto the No. 1 transmission clutch hub.

NOTICE:

Orient the reverse gear and No. 1 transmission clutch hub correctly.



b.

Install the 3 synchromesh shifting key springs and the 3 synchromesh keys onto the No. 1 transmission clutch hub.


Hide 33348A 2.INSTALL 1ST GEAR THRUST WASHER PIN OR BALL

C068014

a.

Coat the 1st gear thrust washer pin or ball with MP grease and install it onto the output shaft.


Hide 33348 3.INSTALL 1ST GEAR THRUST WASHER

C068013

a.

Coat the 1st gear thrust washer with gear oil and install it onto the output shaft.

HINT:

Fit the 1st gear thrust washer pin or ball into the groove of the 1st gear thrust washer correctly.



Hide 33335C 4.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

C068012

a.

Coat the 1st gear needle roller bearing with gear oil and install it onto the output shaft.


Hide 33335 5.INSTALL 1ST GEAR

C068310

a.

Coat the 1st gear with gear oil and install it onto the output shaft.


Hide 33367 6.INSTALL NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR)

a.
C068311

Coat the No. 1 synchronizer ring with gear oil and install it onto the 1st gear.


Hide 33361 7.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

C080547E01
2.028,1.421 2.315,1.622 0.287,0.201 10 SST 1.18,1.398 1.994,1.524 false

a.

Using SST and a press, install the No. 1 transmission clutch hub onto the output shaft.

SST
09316-60011  (09316-00031)

HINT:
·

The 1st gear can be turned.

·

While checking that the 1st gear thrust washer pin or ball is inserted into the groove of the 1st gear thrust washer, press and fit the No. 1 clutch hub.




b.
C068244

Select a snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.039 in.) or less


Snap Ring Thickness:
Part No. Mark Thickness mm (in.)
09520-29018 A 2.50 (0.0984)
09520-29019 B 2.56 (0.1008)
09520-29020 C 2.62 (0.1031)
09520-29021 D 2.68 (0.1055)
09520-29022 E 2.74 (0.1079)
09520-29023 F 2.80 (0.1102)



c.

Using a brass bar and a hammer, install the snap ring onto the output shaft.

NOTICE:

Do not damage the journal surface of the output shaft.



Hide 33332B 8.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

a.
C068246

Coat the 2nd gear needle roller bearing and the 2nd gear bearing spacer with gear oil and install them onto the output shaft.


Hide 33367 9.INSTALL NO. 1 SYNCHRONIZER RING (FOR 2ND GEAR)

a.

Coat the No. 1 synchronizer ring with gear oil.


b.
C157314

Install the No. 1 synchronizer inner ring onto the 2nd gear.


c.
C157315

Install the No. 1 synchronizer middle ring onto the 2nd gear.


d.
C157316

Install the No. 1 synchronizer outer ring onto the 2nd gear.


Hide 33332 10.INSTALL 2ND GEAR

C068248

a.

Coat the 2nd gear with gear oil and install it onto the output shaft.


Hide 33423A 11.INSTALL 3RD DRIVEN GEAR

C080548E01
2.057,1.427 2.344,1.628 0.287,0.201 10 SST 1.192,1.392 2.005,1.518 false

a.

Using SST and a press, install the 3rd driven gear onto the output shaft.

SST
09316-60011  (09316-00031)


Hide 33431C 12.INSTALL OUTPUT GEAR SPACER

C068005

a.

Install the output gear spacer onto the output shaft.


Hide 33422B 13.INSTALL 4TH DRIVEN GEAR

C082013E01
1.512,0.034 1.800,0.235 0.287,0.201 10 SST 1.458,0.152 1.129,0.152 false

a.

Using SST and a press, install the 4th driven gear onto the output shaft.

SST
09612-22011  


Hide 33321A 14.INSTALL OUTPUT SHAFT REAR BEARING

C082014E01
1.422,0.082 1.709,0.283 0.287,0.201 10 SST 1.126,0.193 1.366,0.193 false

a.

Using SST and a press, install the output shaft rear bearing onto the output shaft.

SST
09612-22011  


Hide 33332 15.INSPECT 2ND GEAR RADIAL CLEARANCE

C068254

a.

Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 2nd gear or 2nd gear needle roller bearing.


Hide 33335 16.INSPECT 1ST GEAR RADIAL CLEARANCE

C068309

a.

Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.

Standard clearance:
JTEKT made:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)

NSK made:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:
JTEKT made:

0.058 mm (0.00228 in.)

NSK made:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 1st gear or 1st gear needle roller bearing.


Hide 33332 17.INSPECT 2ND GEAR THRUST CLEARANCE

C068312

a.

Using a dial indicator, measure the 2nd gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0217 in.)


Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear, or 3rd driven gear.


Hide 33335 18.INSPECT 1ST GEAR THRUST CLEARANCE

C080538

a.

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard clearance:

0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum clearance:

0.40 mm (0.0157 in.)


If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear, or No. 1 transmission clutch hub.