43448G
1.REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
for One Touch Type:
Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and remove the front No. 2 axle inboard joint boot clamp.
for Claw Engagement Type:
Using needle-nose pliers, disengage the 2 claws and remove the front No. 2 axle inboard joint boot clamp.
43448F
2.REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP
for One Touch Type:
Using a screwdriver, release the staked part of the front axle inboard joint boot clamp and separate the front axle inboard joint boot clamp.
for Claw Engagement Type:
Using needle-nose pliers, disengage the 2 claws and remove the front axle inboard joint boot clamp.
3.SEPARATE FRONT AXLE INBOARD JOINT BOOT
Separate the front axle inboard joint boot from the front drive inboard joint assembly.
43040
4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
Remove the old grease from the front drive inboard joint assembly.
Place matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
| *a | Matchmark |
Do not cause any damage when placing the marks.
Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.
Fix the front drive outboard joint shaft assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using a snap ring expander, remove the snap ring.
Place matchmarks on the tripod joint assembly and front drive outboard joint shaft assembly.
| *a | Matchmark |
Do not cause any damage when placing the marks.
Using a brass bar and hammer, remove the tripod joint assembly.
Do not tap the rollers.
Remove the front axle inboard joint boot and front axle inboard joint boot clamp.
43474F
5.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ 1 Clamp)
for One Touch Type:
Using a screwdriver, release the staked part of the front drive shaft damper clamp RH and remove the front drive shaft damper clamp RH.
| *a | for One Touch Type |
| *b | for Claw Engagement Type |
for Claw Engagement Type:
Using needle-nose pliers, disengage the 2 claws and remove the front drive shaft damper clamp RH.
43474F
6.REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ 2 Clamps)
Using needle-nose pliers, disengage the 4 claws and remove the 2 front drive shaft damper clamps RH.
43474D
7.REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ 1 Clamp)
Remove the front drive shaft damper RH from the front drive outboard joint shaft assembly.
43474D
8.REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ 2 Clamps)
Remove the front drive shaft damper RH from the front drive outboard joint shaft assembly.
43447F
9.REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and remove the front No. 2 axle outboard joint boot clamp.
43447E
10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP
Using a screwdriver, release the staked part of the front axle outboard joint boot clamp and remove the front axle outboard joint boot clamp.
11.REMOVE FRONT AXLE OUTBOARD JOINT BOOT
Remove the front axle outboard joint boot from the front drive outboard joint shaft assembly.
Remove the old grease from the front drive outboard joint shaft assembly.
43420G
12.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
Using a screwdriver, remove the front drive shaft hole snap ring LH.
43410N
13.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING RH
Use the same procedure for the RH side as for the LH side.
41336E
14.REMOVE FRONT DRIVE SHAFT DUST COVER
Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.
Do not drop the front drive inboard joint assembly.