Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › from 2014.07
RM19S0E _53 Suspension _051471 ALIGNMENT / HANDLING DIAGNOSIS _0248213 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

For vehicles equipped with VSC, if wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection.


PROCEDURE

Hide 3.INSPECT CAMBER

a.

Install the camber-caster-kingpin gauge and position the rear wheel on the turning radius gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle)
Tire Size Camber Right - Left Error
175/70R14 -1°00' +/- 30' (-1.00° +/- 0.5°) 0°30' (0.5°)
175/65R15 -1°00' +/- 30' (-1.00° +/- 0.5°) 0°30' (0.5°)

NOTICE:

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers. If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.



Hide 4.INSPECT TOE-IN

a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968E18
1.344,0.615 0.958,1.125 0.958,1.125 0.833,0.583 true 2.521,1.333 2.521,1.667 false 0.854,1.135 1.031,1.302 0.177,0.167 10 false *a 2.438,1.698 2.615,1.854 0.177,0.156 10 false *b

Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

NOTICE:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969E07
0.556,1.641 0.727,1.801 0.172,0.160 10 *a 0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.703 0.140,0.160 10 C 3.071,0.55 3.210,0.710 0.140,0.160 10 D 2.498,0.717 2.638,0.877 0.140,0.160 10 A 2.509,1.537 2.649,1.697 0.140,0.160 10 B

Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle)
Tire Size Specified Condition
175/70R14 C + D: 0°22' +/- 15' ( 0.38° +/- 0.25°)
B - A: 4.0 +/- 3.0 mm (0.157 +/- 0.118 in.)
175/65R15 C + D: 0°22' +/- 15' ( 0.38° +/- 0.25°)
B - A: 4.0 +/- 3.0 mm (0.157 +/- 0.118 in.)

HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.