Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2011.08–2014.07
RM19S0E _53 Suspension _051471 ALIGNMENT / HANDLING DIAGNOSIS _0248214 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

For vehicles equipped with VSC, if wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

1.

Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).



PROCEDURE

Hide 2.MEASURE VEHICLE HEIGHT

Measuring points:
A:

Ground clearance of front wheel center

B:

Ground clearance of front lower arm set front bolt center

C:

Ground clearance of rear wheel center

D:

Ground clearance of axle beam set bolt center


C235025E01
1.834,3.73 1.965,3.894 0.131,0.164 10 D 1.433,3.771 1.565,3.935 0.131,0.164 10 B 0.193,3.685 0.325,3.849 0.131,0.164 10 A 3.213,3.697 3.344,3.861 0.131,0.164 10 C 1.908,2.066 2.039,2.230 0.131,0.164 10 D 1.322,2.066 1.453,2.230 0.131,0.164 10 B 0.202,2.066 0.333,2.230 0.131,0.164 10 A 3.149,2.066 3.281,2.230 0.131,0.164 10 C

NOTICE:
·

Before inspecting the wheel alignment, check the vehicle height.

·

The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



HINT:

Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.


Vehicle Height (Unloaded Vehicle)
Model Tire Size Front A-B Rear C-D
Except for Rough Road Package 175/70 R14 97 mm
(3.82 in.)
32 mm
(1.26 in.)
175/65 R15 97 mm
(3.82 in.)
32 mm
(1.26 in.)
175/65 R14 87 mm
(3.43 in.)
25 mm
(0.98 in.)
185/60 R15 87 mm
(3.43 in.)
24 mm
(0.94 in.)
Rough Road Package 175/65 R14 67 mm
(2.64 in.)
5 mm
(0.20 in.)
185/60 R15 67 mm
(2.64 in.)
4 mm
(0.16 in.)

Hide 3.INSPECT WHEEL TURNING ANGLE

a.
C132439E12
0.564,0.15 0.747,0.327 0.184,0.176 10 *a 2.784,0.167 2.968,0.344 0.184,0.176 10 *a 2.424,0.167 2.607,0.344 0.184,0.176 10 *b 0.895,0.15 1.079,0.327 0.184,0.176 10 *b

Fully turn the steering wheel left and right, and measure the wheel turning angle.

Text in Illustration
*a Inside
*b Outside
V100135

Front of the Vehicle

Wheel Turning Angle (Unloaded Vehicle)
Model Tire Size Inside Wheel Outside Wheel
Except for Rough Road Package 175/70 R14 40°44 ' +/- 2°
(40.73° +/- 2°)
35°03'
(35.05°)
175/65 R15 40°44 ' +/- 2°
(40.73° +/- 2°)
35°03'
(35.05°)
175/65 R14 41°01' +/- 2°
(41.02° +/- 2°)
35°15'
(35.25°)
185/60 R15 41°01' +/- 2°
(41.02° +/- 2°)
35°15'
(35.25°)
Rough Road Package 175/65 R14 41°35' +/- 2°
(41.58° +/- 2°)
35°43'
(35.72°)
185/60 R15 41°35' +/- 2°
(41.58° +/- 2°)
35°43'
(35.72°)

If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.


Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

a.
C132440E17
0.709,0.611 0.927,0.808 0.218,0.197 10 *1 2.403,1.106 2.51,0.827 2.51,0.827 2.738,0.827 false 0.91,0.704 1.036,0.704 1.036,0.704 1.036,1.478 false 2.784,0.731 3.002,0.928 0.218,0.197 10 *2

Put the front wheel on the center of the alignment tester.

Text in Illustration
*1 Alignment tester
*2 Camber-caster-steering axis inclination gauge


b.

Remove the wheel cap.


c.

Set the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.


d.

Inspect the camber, caster and steering axis inclination.

Camber Inclination (Unloaded Vehicle)
Model Tire Size Camber
Except for Rough Road Package 175/70 R14 -0°21' +/- 45'
(-0.35° +/- 0.75°)
175/65 R15 -0°21' +/- 45'
(-0.35° +/- 0.75°)
175/65 R14 -0°15' +/- 45'
(-0.25° +/- 0.75°)
185/60 R15 -0°15' +/- 45'
(-0.25° +/- 0.75°)
Rough Road Package 175/65 R14 0°02' +/- 45'
(0.03° +/- 0.75°)
185/60 R15 0°02' +/- 45'
(0.03° +/- 0.75°)

Caster Inclination (Unloaded Vehicle)
Model Tire Size Transmission Caster
Except for Rough Road Package 175/70 R14 C54
U441E
4°59' +/- 45'
(4.98° +/- 0.75°)
175/65 R15 C54
U340E
U441E
4°60' +/- 45'
(5.00° +/- 0.75°)
175/65 R14 C54 4°53' +/- 45'
(4.88° +/- 0.75°)
U441E 4°52' +/- 45'
(4.87° +/- 0.75°)
185/60 R15 C54 4°54' +/- 45'
(4.90° +/- 0.75°)
U340E
U441E
4°53' +/- 45'
(4.88° +/- 0.75°)
Rough Road Package 175/65 R14 C54 4°34' +/- 45'
(4.57° +/- 0.75°)
U441E 4°33' +/- 45'
(4.55° +/- 0.75°)
185/60 R15 C54 4°35' +/- 45'
(4.58° +/- 0.75°)
U340E
U441E
4°34' +/- 45'
(4.57° +/- 0.75°)

Steering Axis Inclination (Unloaded Vehicle)
Model Tire Size Steering Axis Inclination
(Reference)
Except for Rough Road Package 175/70 R14 11°21'
(11.35°)
175/65 R15 11°21'
(11.35°)
175/65 R14 11°09'
(11.15°)
185/60 R15 11°09'
(11.15°)
Rough Road Package 175/65 R14 10°40'
(10.67°)
185/60 R15 10°40'
(10.67°)

NOTICE:
·

Perform the inspection while the vehicle is empty (without a spare tire or tools on board).

·

The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.




e.

Remove the camber-caster-steering axis inclination gauge and attachment.


f.

Install the wheel cap.

If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.


Hide 5.ADJUST CAMBER

NOTICE:

Inspect the toe-in after the camber has been adjusted.


a.

Remove the front wheel.


b.

w/ ABS:

i.
C125274

Remove the bolt and separate the speed sensor and flexible hose.



c.
C125275

Remove the 2 nuts from the lower side of the shock absorber.

HINT:

Keep the bolt from rotating while loosening and removing the nuts.



d.

Clean the installation surfaces of the shock absorber and steering knuckle.


e.

Provisionally install the 2 nuts (Step A).


f.
C205448E03
1.073,0.26 1.271,0.448 0.198,0.188 10 false (+) 2.677,0.25 2.875,0.438 0.198,0.188 10 false (-)

Fully push or pull the axle hub in the direction of the required adjustment (Step B).


g.
C125275

Tighten the 2 nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

HINT:

Keep the bolt from rotating while loosening and removing the nuts.



h.

w/ ABS:

i.
C125274

Install the flexible hose and speed sensor with the bolt.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the flexible hose and speed sensor without twisting them.




i.

Install the front wheel.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)


j.
C234652E01
0.227,1.117 0.322,1.258 0.095,0.142 10 1 0.209,1.362 0.305,1.503 0.095,0.142 10 2 0.341,1.194 0.553,1.194 false 0.324,1.439 0.536,1.439 false

Check the camber.

If the measured value is not within the specifications, calculate the required adjustment amount using the formula below.

(Camber adjustment amount) = Center of specified range - Measured value

Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to within the specified range.

HINT:

Try to adjust the camber to the center of the specified range.


Move axle toward (+) in step (B) Refer to table (1) (Move axle toward positive side)
Move axle toward (-) in step (B) Refer to table (2) (Move axle toward negative side)


k.

Table (1) (Move the axle toward the positive side)

C111317E31
1.781,3.354 2.542,3.583 false 1.792,3.115 2.552,3.354 false 1.792,2.875 3.302,3.354 false 1.792,2.635 3.302,3.115 false 1.792,2.396 4.063,3.115 false 1.792,2.156 4.063,2.875 false 2.552,2.156 4.813,2.875 false 3.302,2.156 4.813,2.635 false 4.063,2.156 5.563,2.635 false 4.813,2.167 5.563,2.406 false 5.552,2.156 6.313,2.396 false 6.313,3.583 7.063,3.823 false 6.313,3.823 7.063,4.063 false 5.552,3.823 7.063,4.302 false 5.552,4.063 7.063,4.542 false 4.802,4.063 7.063,4.781 false 4.802,4.292 7.063,5.01 false 4.073,4.292 6.333,5.01 false 4.073,4.531 5.573,5.01 false 3.313,4.531 4.823,5.01 false 3.313,4.771 4.073,5.01 false 2.563,4.771 3.313,5.01 false 0.656,0.615 1.24,0.99 0.583,0.375 10 false Installed Bolt 0.229,1.635 0.833,1.99 0.604,0.354 10 false Adjusting Value 1.573,0.792 1.74,0.99 0.167,0.198 10 false 1 0.906,6.063 1.073,6.26 0.167,0.198 10 false 1 1.573,1.656 1.719,1.865 0.146,0.208 10 false 2 0.906,6.958 1.052,7.167 0.146,0.208 10 false 2 0.104,0.219 3.198,0.406 3.094,0.188 10 false Table (1) (Move the axle toward the positive side) 0.667,5.208 2.354,5.385 1.688,0.177 10 false Selected Bolt Combination 4.365,2.927 4.5,3.083 0.135,0.156 10 false G 3.615,3.167 3.75,3.323 0.135,0.156 10 false G 5.875,2.448 6.01,2.604 0.135,0.156 10 false G 5.125,2.688 5.26,2.844 0.135,0.156 10 false G 6.625,2.208 6.76,2.365 0.135,0.156 10 false G 2.854,3.396 2.99,3.552 0.135,0.156 10 false G 2.125,3.615 2.26,3.771 0.135,0.156 10 false A 4.365,3.167 4.5,3.323 0.135,0.156 10 false A 5.125,2.927 5.26,3.083 0.135,0.156 10 false A 6.625,2.448 6.76,2.604 0.135,0.156 10 false A 3.615,3.396 3.75,3.552 0.135,0.156 10 false A 6.625,2.688 6.76,2.844 0.135,0.156 10 false B 4.365,3.396 4.5,3.552 0.135,0.156 10 false B 5.875,2.927 6.01,3.083 0.135,0.156 10 false B 5.125,3.167 5.26,3.323 0.135,0.156 10 false B 2.854,3.635 2.99,3.792 0.135,0.156 10 false B 2.125,3.865 2.26,4.021 0.135,0.156 10 false B 3.052,5.5 3.188,5.656 0.135,0.156 10 false C 5.125,3.396 5.26,3.552 0.135,0.156 10 false C 5.875,3.167 6.01,3.323 0.135,0.156 10 false C 3.615,3.635 3.75,3.792 0.135,0.156 10 false C 2.854,3.875 2.99,4.031 0.135,0.156 10 false C 6.625,2.927 6.76,3.083 0.135,0.156 10 false C 1.552,5.5 1.688,5.656 0.135,0.156 10 false A 2.125,4.104 2.26,4.26 0.135,0.156 10 false C 6.073,5.5 6.208,5.656 0.135,0.156 10 false G 2.302,5.5 2.438,5.656 0.135,0.156 10 false B 2.125,4.344 2.26,4.5 0.135,0.156 10 false D 2.854,4.115 2.99,4.271 0.135,0.156 10 false D 3.615,3.875 3.75,4.031 0.135,0.156 10 false D 5.875,3.396 6.01,3.552 0.135,0.156 10 false D 4.365,3.635 4.5,3.792 0.135,0.156 10 false D 6.625,3.167 6.76,3.323 0.135,0.156 10 false D 3.813,5.5 3.948,5.656 0.135,0.156 10 false D 2.854,4.354 2.99,4.51 0.135,0.156 10 false E 3.615,4.115 3.75,4.271 0.135,0.156 10 false E 5.125,3.635 5.26,3.792 0.135,0.156 10 false E 2.125,4.583 2.26,4.74 0.135,0.156 10 false E 6.625,3.396 6.76,3.552 0.135,0.156 10 false E 4.563,5.5 4.698,5.656 0.135,0.156 10 false E 4.354,3.875 4.49,4.031 0.135,0.156 10 false E 5.323,5.5 5.458,5.656 0.135,0.156 10 false F 2.125,4.823 2.26,4.979 0.135,0.156 10 false F 3.615,4.354 3.75,4.51 0.135,0.156 10 false F 4.365,4.115 4.5,4.271 0.135,0.156 10 false F 5.125,3.875 5.26,4.031 0.135,0.156 10 false F 2.854,4.583 2.99,4.74 0.135,0.156 10 false F 5.875,3.635 6.01,3.792 0.135,0.156 10 false F 5.875,2.688 6.01,2.844 0.135,0.156 10 false A 0.458,2.198 1.573,2.375 1.115,0.177 10 false -1° 30' to -1° 15' 0.458,2.438 1.573,2.615 1.115,0.177 10 false -1° 15' to -1° 00' 0.458,2.677 1.573,2.854 1.115,0.177 10 false -1° 00' to -0° 45' 0.458,2.917 1.573,3.094 1.115,0.177 10 false -0° 45' to -0° 30' 0.458,3.156 1.573,3.333 1.115,0.177 10 false -0° 30' to -0° 15' 0.458,3.396 1.573,3.573 1.115,0.177 10 false -0° 15' to 0° 0.5,3.625 0.844,3.792 0.344,0.167 10 false 0° 0.5,3.875 1.573,4.042 1.073,0.167 10 false 0° 15' to 0° 30' 0.51,4.104 1.583,4.271 1.073,0.167 10 false 0° 30' to 0° 45' 0.5,4.344 1.573,4.51 1.073,0.167 10 false 0° 45' to 1° 00' 0.5,4.583 1.573,4.75 1.073,0.167 10 false 1° 00' to 1° 15' 0.5,4.823 1.573,4.99 1.073,0.167 10 false 1° 15' to 1° 30' 1.979,0.99 2.729,1.302 0.75,0.313 10 false 90109-15001 2.74,0.99 3.49,1.302 0.75,0.313 10 false 90109-15001 3.5,0.979 4.25,1.292 0.75,0.313 10 false 90109-15001 4.24,0.99 4.99,1.302 0.75,0.313 10 false 90109-15001 5,0.99 5.75,1.302 0.75,0.313 10 false 90109-15002 5.771,0.969 6.521,1.281 0.75,0.313 10 false 90109-15003 6.51,0.979 7.104,1.292 0.594,0.313 10 false 90109-15004 6.5,1.844 7.073,2.167 0.573,0.323 10 false 90109-15004 5.76,1.854 6.51,2.167 0.75,0.313 10 false 90109-15004 5,1.844 5.75,2.156 0.75,0.313 10 false 90109-15004 4.24,1.844 4.99,2.156 0.75,0.313 10 false 90109-15004 3.49,1.854 4.24,2.167 0.75,0.313 10 false 90109-15003 2.729,1.854 3.479,2.167 0.75,0.313 10 false 90109-15002 2,1.844 2.677,2.167 0.677,0.323 10 false 90109-15001 1.417,6.26 2.167,6.573 0.75,0.313 10 false 90109-15001 1.406,7.115 2.156,7.427 0.75,0.313 10 false 90109-15002 4.427,6.24 5.177,6.552 0.75,0.313 10 false 90109-15003 5.177,6.26 5.927,6.573 0.75,0.313 10 false 90109-15004 2.167,6.26 2.917,6.573 0.75,0.313 10 false 90109-15001 2.917,6.26 3.667,6.573 0.75,0.313 10 false 90109-15001 3.677,6.25 4.427,6.563 0.75,0.313 10 false 90109-15002 5.958,6.26 6.708,6.573 0.75,0.313 10 false 90109-15001 5.948,7.125 6.698,7.438 0.75,0.313 10 false 90109-15001 5.188,7.125 5.938,7.438 0.75,0.313 10 false 90109-15004 4.427,7.115 5.177,7.427 0.75,0.313 10 false 90109-15004 3.667,7.125 4.417,7.438 0.75,0.313 10 false 90109-15004 2.938,7.125 3.688,7.438 0.75,0.313 10 false 90109-15004 2.177,7.125 2.927,7.438 0.75,0.313 10 false 90109-15003 0.875,3.625 1.438,3.813 0.563,0.188 10 false to 0° 15'


l.

Table (2) (Move the axle toward the negative side).

C111317E32
6.323,2.156 7.042,2.396 false 5.573,2.167 7.063,2.625 false 4.813,2.177 7.063,2.875 false 4.052,2.167 7.063,3.125 false 3.302,2.167 7.052,3.333 false 7.052,3.573 2.552,2.177 false 1.813,4.781 2.531,5 false 1.802,4.531 3.313,5.01 false 1.802,4.292 4.073,5.01 false 1.802,4.083 4.802,5 false 1.802,3.813 5.573,5.01 false 1.802,3.594 6.292,5 false 0.656,0.573 1.24,0.948 0.583,0.375 10 false Installed Bolt 0.229,1.594 0.833,1.948 0.604,0.354 10 false Adjusting Value 1.563,0.75 1.729,0.948 0.167,0.198 10 false 1 0.906,6.021 1.073,6.219 0.167,0.198 10 false 1 1.563,1.615 1.708,1.823 0.146,0.208 10 false 2 0.906,6.917 1.052,7.125 0.146,0.208 10 false 2 0.104,0.177 3.281,0.365 3.177,0.188 10 false Table (2) (Move the axle toward the negative side) 0.667,5.219 2.344,5.375 1.677,0.156 10 false Selected Bolt Combination 4.375,3.635 4.49,3.781 0.115,0.146 10 false B 2.135,2.917 2.25,3.063 0.115,0.146 10 false C 4.375,3.396 4.5,3.542 0.125,0.146 10 false D 2.135,2.448 2.25,2.594 0.115,0.146 10 false E 5.135,3.156 5.24,3.313 0.104,0.156 10 false F 3.635,3.865 3.771,4.021 0.135,0.156 10 false G 4.375,4.104 4.51,4.26 0.135,0.156 10 false G 6.656,4.823 6.792,4.979 0.135,0.156 10 false G 5.125,4.344 5.26,4.5 0.135,0.156 10 false G 5.875,4.583 6.01,4.74 0.135,0.156 10 false G 2.865,3.625 3,3.781 0.135,0.156 10 false G 3.646,3.396 3.76,3.542 0.115,0.146 10 false C 2.865,3.156 2.979,3.302 0.115,0.146 10 false C 5.885,3.875 6,4.021 0.115,0.146 10 false C 5.135,3.635 5.25,3.781 0.115,0.146 10 false C 6.656,4.104 6.771,4.25 0.115,0.146 10 false C 4.375,3.875 4.49,4.021 0.115,0.146 10 false A 5.135,4.115 5.25,4.26 0.115,0.146 10 false A 3.646,3.625 3.76,3.771 0.115,0.146 10 false A 2.135,3.396 2.25,3.542 0.115,0.146 10 false A 5.885,4.344 6,4.49 0.115,0.146 10 false A 6.656,4.583 6.771,4.729 0.115,0.146 10 false A 4.385,2.917 4.49,3.073 0.104,0.156 10 false F 5.896,3.396 6,3.552 0.104,0.156 10 false F 2.875,2.438 2.979,2.594 0.104,0.156 10 false F 2.135,2.208 2.24,2.365 0.104,0.156 10 false F 3.646,2.677 3.75,2.833 0.104,0.156 10 false F 5.885,4.115 6,4.26 0.115,0.146 10 false B 5.135,3.875 5.25,4.021 0.115,0.146 10 false B 6.667,4.344 6.781,4.49 0.115,0.146 10 false B 2.875,3.396 2.99,3.542 0.115,0.146 10 false B 2.135,3.156 2.25,3.302 0.115,0.146 10 false B 2.865,2.677 2.979,2.823 0.115,0.146 10 false E 4.375,3.156 4.49,3.302 0.115,0.146 10 false E 5.135,3.396 5.25,3.542 0.115,0.146 10 false E 6.656,3.625 6.771,3.771 0.115,0.146 10 false E 3.646,2.917 3.76,3.063 0.115,0.146 10 false E 3.646,3.156 3.771,3.302 0.125,0.146 10 false D 2.135,2.677 2.26,2.823 0.125,0.146 10 false D 6.656,3.865 6.781,4.01 0.125,0.146 10 false D 5.885,3.635 6.01,3.781 0.125,0.146 10 false D 2.865,2.917 2.99,3.063 0.125,0.146 10 false D 0.458,2.198 1.573,2.365 1.115,0.167 10 false -1° 30' to -1° 15' 0.458,2.417 1.573,2.583 1.115,0.167 10 false -1° 15' to -1° 00' 0.458,2.667 1.573,2.833 1.115,0.167 10 false -1° 00' to -0° 45' 0.458,2.906 1.573,3.073 1.115,0.167 10 false -0° 45' to -0° 30' 0.458,3.146 1.573,3.313 1.115,0.167 10 false -0° 30' to -0° 15' 0.458,3.375 1.573,3.542 1.115,0.167 10 false -0° 15' to 0° 0.49,3.615 0.729,3.781 0.24,0.167 10 false 0° 0.5,3.854 1.573,4.021 1.073,0.167 10 false 0° 15' to 0° 30' 0.5,4.094 1.573,4.26 1.073,0.167 10 false 0° 30' to 0° 45' 0.5,4.333 1.573,4.5 1.073,0.167 10 false 0° 45' to 1° 00' 0.5,4.573 1.573,4.74 1.073,0.167 10 false 1° 00' to 1° 15' 0.5,4.813 1.573,4.979 1.073,0.167 10 false 1° 15' to 1° 30' 1.552,5.469 1.667,5.615 0.115,0.146 10 false A 2.313,5.469 2.427,5.615 0.115,0.146 10 false B 3.063,5.469 3.177,5.615 0.115,0.146 10 false C 3.823,5.469 3.938,5.615 0.115,0.146 10 false D 4.573,5.469 4.688,5.615 0.115,0.146 10 false E 5.333,5.469 5.448,5.615 0.115,0.146 10 false F 6.083,5.469 6.208,5.615 0.125,0.146 10 false G 1.99,0.969 2.51,1.323 0.521,0.354 10 false 90109-15001 5.75,0.969 6.271,1.323 0.521,0.354 10 false 90109-15003 6.5,0.99 7.021,1.344 0.521,0.354 10 false 90109-15004 2.729,0.969 3.25,1.323 0.521,0.354 10 false 90109-15001 3.49,0.979 4.01,1.333 0.521,0.354 10 false 90109-15001 4.25,0.979 4.771,1.333 0.521,0.354 10 false 90109-15001 4.99,0.969 5.51,1.323 0.521,0.354 10 false 90109-15002 1.99,1.844 2.51,2.198 0.521,0.354 10 false 90109-15001 2.729,1.854 3.25,2.208 0.521,0.354 10 false 90109-15002 3.479,1.833 4,2.188 0.521,0.354 10 false 90109-15003 4.26,1.833 4.781,2.188 0.521,0.354 10 false 90109-15004 4.958,1.844 5.479,2.198 0.521,0.354 10 false 90109-15004 5.76,1.844 6.281,2.198 0.521,0.354 10 false 90109-15004 6.521,1.854 7.042,2.208 0.521,0.354 10 false 90109-15004 5.188,6.26 5.708,6.615 0.521,0.354 10 false 90109-15004 1.406,6.25 1.927,6.604 0.521,0.354 10 false 90109-15001 3.667,6.26 4.188,6.615 0.521,0.354 10 false 90109-15002 4.417,6.25 4.938,6.604 0.521,0.354 10 false 90109-15003 2.167,6.26 2.688,6.615 0.521,0.354 10 false 90109-15001 2.927,6.26 3.448,6.615 0.521,0.354 10 false 90109-15001 5.938,6.25 6.438,6.563 0.5,0.313 10 false 90109-15001 1.427,7.115 1.958,7.438 0.531,0.323 10 false 90109-15002 2.177,7.115 2.698,7.469 0.521,0.354 10 false 90109-15003 2.917,7.115 3.438,7.469 0.521,0.354 10 false 90109-15004 3.677,7.125 4.198,7.479 0.521,0.354 10 false 90109-15004 4.427,7.115 4.948,7.469 0.521,0.354 10 false 90109-15004 5.198,7.125 5.698,7.469 0.5,0.344 10 false 90109-15004 5.927,7.125 6.448,7.458 0.521,0.333 10 false 90109-15001 0.875,3.615 1.406,3.792 0.531,0.177 10 false to 0°15'

The body and suspension may be damaged if the camber is not correctly adjusted in accordance with the above table.

NOTICE:

Replace the nut with a new one when replacing the bolt.



m.

Repeat the steps mentioned above. At step (A), replace 1 or 2 selected bolts.

HINT:

Replace one bolt at a time when replacing 2 bolts.



Hide 6.INSPECT TOE-IN

a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to the neutral position.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C241642E03
0.833,0.573 1.073,1.167 1.073,1.167 1.396,0.573 true 2.823,0.458 2.719,0.458 2.719,0.458 2.615,1.292 true 0.958,1.177 1.135,1.333 0.177,0.156 10 false *a 2.875,0.375 3,0.542 0.125,0.167 10 false B

Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).

Text in Illustration
*a Tread Center Mark


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C241643E03
0.542,1.01 0.25,1.448 true 2.542,0.74 2.677,0.896 0.135,0.156 10 false A 2.542,1.771 2.677,1.927 0.135,0.156 10 false B 0.188,1.49 0.323,1.646 0.135,0.156 10 false A

Measure the distance between the tread center marks on the front side of the wheels (Dimension A).

Text in Illustration
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle)
Model Tire Size Specified Condition
Except for Rough Road Package 175/70 R14 B-A: 1.2 +/- 2.0 mm
(0.0472 +/- 0.0787 in.)
175/65 R15 B-A: 1.2 +/- 2.0 mm
(0.0472 +/- 0.0787 in.)
175/65 R14 B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.)
185/60 R15 B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.)
Rough Road Package 175/65 R14 B-A: 1.3 +/- 2.0 mm
(0.0512 +/- 0.0787 in.)
185/60 R15 B-A: 1.4 +/- 2.0 mm
(0.0551 +/- 0.0787 in.)

If the toe-in is not within the specified value, adjust it at the rack ends.


Hide 7.ADJUST TOE-IN

C106036

a.

Measure the thread lengths of the right and left rack ends.

Standard:

Difference in thread length of 1.5 mm (0.0591 in.) or less



b.

Remove the rack boot set clips.


c.

Loosen the tie rod end lock nuts.


d.

Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

i.

Extend the shorter rack end if the measured toe-in deviates toward the outer-side.


ii.

Shorten the longer rack end if the measured toe-in deviates toward the inner-side.



e.

Turn the right and left rack ends by an equal amount to adjust the toe-in.

HINT:

Try to adjust the toe-in to the center of the specified range.



f.

Make sure that the lengths of the right and left rack ends are the same.

Toe-in (Unloaded Vehicle)
Model Tire Size Specified Condition
Except for Rough Road Package 175/70 R14 B-A: 1.2 +/- 1.0 mm
(0.0472 +/- 0.0394 in.)
175/65 R15 B-A: 1.2 +/- 1.0 mm
(0.0472 +/- 0.0394 in.)
175/65 R14 B-A: 1.3 +/- 1.0 mm
(0.0512 +/- 0.0394 in.)
185/60 R15 B-A: 1.3 +/- 1.0 mm
(0.0512 +/- 0.0394 in.)
Rough Road Package 175/65 R14 B-A: 1.3 +/- 1.0 mm
(0.0512 +/- 0.0394 in.)
185/60 R15 B-A: 1.4 +/- 1.0 mm
(0.0551 +/- 0.0394 in.)


g.

Tighten the tie rod end lock nuts to the specified torque.

Torque:
75 N*m (760 kgf*cm, 55 ft.*lbf)

NOTICE:

Provisionally tighten the lock nut while holding the hexagonal part of the steering rack end so that the lock nut and the steering rack end do not turn together. Hold the flat of the tie rod end and tighten the lock nut.



h.

Place the boots on the seats.


i.
C342535E02
0.875,0.417 1.365,0.625 0.49,0.208 10 false 54°30' 1.823,0.281 2.135,0.479 0.313,0.198 10 false *a 0.625,1.51 0.938,1.708 0.313,0.198 10 false *b 2.333,0.688 2.646,0.885 0.313,0.198 10 false *c

Using pliers, install the RH and LH boot clips as shown in the illustration.

Text in Illustration
*a Upper Side
*b Front Side
*c 180° (Clip installation range)

NOTICE:
·

Install the clip so that its claws are within the clip installation range.

·

Make sure that the rack boots are not twisted.




Hide 8. FRONT WHEELS FACING STRAIGHT AHEAD