Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.08–2014.07
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1403  Rear Speed Sensor RH Malfunction  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for ABS control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.


C151818E49
1.563,0.865 1.563,0.469 1.563,0.469 1.469,0.469 false 5.594,1.333 6.01,1.333 false 1.313,0.385 1.5,0.552 0.188,0.167 10 false *1 4.292,2.115 4.469,2.281 0.177,0.167 10 false *b 6.083,1.26 6.74,1.427 0.656,0.167 10 false 1.6 V 6.083,1.625 6.729,1.792 0.646,0.167 10 false 0.8 V 5.24,2.115 5.417,2.281 0.177,0.167 10 false *c 1.521,2.177 1.719,2.344 0.198,0.167 10 false *2 3.385,0.75 3.563,0.917 0.177,0.167 10 false *a

Text in Illustration
*1 Speed Sensor *2 Speed Sensor Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -

DTC No. DTC Detection Condition Trouble Area
C1403
C1404
Any of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed less than 10 km/h (6 mph), outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h)


·

Rear speed sensor RH/LH

·

Speed sensor rotor



Test Mode Diagnosis Code
DTC No. DTC Detection Condition Trouble Area
C1273
C1274
Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Speed sensor rotor



HINT:
·

DTC C1403 and C1273 are for the rear speed sensor RH.

·

DTC C1404 and C1274 are for the rear speed sensor LH.



WIRING DIAGRAM

C243290E02
3.373,0.433 3.660,0.593 0.287,0.160 10 VK1 3.449,0.241 3.560,0.412 0.111,0.171 10 1 3.373,0.923 3.660,1.083 0.287,0.160 10 VK1 3.449,0.731 3.560,0.902 0.111,0.171 10 2 2.48,0.421 2.690,0.576 0.210,0.155 10 V1 2.48,0.925 2.690,1.080 0.210,0.155 10 V1 2.537,0.248 2.647,0.419 0.111,0.171 10 2 2.537,0.739 2.647,0.910 0.111,0.171 10 1 2.275,0.424 2.385,0.584 0.111,0.160 10 + 2.314,0.941 2.386,1.101 0.072,0.160 10 - 2.4,1.313 4.228,1.484 1.828,0.171 10 Skid Control Sensor Wire LH 5.64,0.319 5.833,0.485 0.193,0.166 10 5 5.64,0.81 5.833,0.975 0.193,0.166 10 4 5.881,0.494 6.168,0.654 0.287,0.160 10 RL+ 5.881,1.011 6.168,1.171 0.287,0.160 10 RL- 3.359,2.004 3.680,2.164 0.321,0.160 10 WK1 3.463,1.812 3.574,1.984 0.111,0.171 10 1 3.359,2.495 3.680,2.655 0.321,0.160 10 WK1 3.463,2.303 3.574,2.474 0.111,0.171 10 2 2.477,1.993 2.709,2.147 0.232,0.155 10 W1 2.477,2.483 2.709,2.638 0.232,0.155 10 W1 2.551,1.82 2.661,1.991 0.111,0.171 10 2 2.551,2.31 2.661,2.481 0.111,0.171 10 1 2.294,1.996 2.399,2.156 0.105,0.160 10 + 2.328,2.512 2.400,2.672 0.072,0.160 10 - 2.414,2.884 4.242,3.055 1.828,0.171 10 Skid Control Sensor Wire RH 5.584,1.891 5.777,2.057 0.193,0.166 10 17 5.412,2.739 5.682,2.888 0.270,0.149 10 A55 5.584,2.381 5.777,2.547 0.193,0.166 10 16 5.881,2.066 6.245,2.226 0.364,0.160 10 RR+ 5.881,2.582 6.168,2.742 0.287,0.160 10 RR- 5.408,2.928 7.095,3.231 1.687,0.303 10 Skid Control ECU (Brake Actuator Assembly) 0.198,1.821 1.572,2.647 1.373,0.826 10 Rear Axle Hub and Bearing assembly RH (Rear Speed Sensor, Rear Speed Sensor Rotor) 0.263,0.196 1.637,1.022 1.373,0.826 10 Rear Axle Hub and Bearing assembly LH (Rear Speed Sensor, Rear Speed Sensor Rotor)

CAUTION / NOTICE / HINT

NOTICE:

Disassembly of the speed sensor from the rear axle hub and bearing assembly is prohibited.


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C118693E02
0.676,0.188 0.859,0.363 0.183,0.175 10 *a 2.229,0.188 2.412,0.363 0.183,0.175 10 *b 1.738,1.666 1.922,1.836 0.185,0.170 10 *c

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



Text in Illustration
*a Normal
*b Abnormal
*c Clearance


OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC (Skid Control ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h When driving at constant speed: No large fluctuations
RL Wheel Speed RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h When driving at constant speed: No large fluctuations


d.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).





OK

END

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY