Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU (brake actuator assembly) via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.

DTC No. DTC Detection Condition Trouble Area
C1432 Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

Steering angle sensor power supply

·

Steering angle sensor (Spiral cable sub-assembly)



WIRING DIAGRAM

C243293E01
0.741,2.535 2.506,2.686 1.765,0.151 10 : CAN Communication Line 1.081,0.686 1.991,0.849 0.910,0.163 10 ECU-IG NO. 1 1.324,1.092 1.787,1.255 0.464,0.163 10 DOME 3.177,0.483 3.272,0.627 0.095,0.144 10 5 3.338,0.571 3.517,0.720 0.179,0.149 10 IG 3.177,0.889 3.272,1.033 0.095,0.144 10 6 3.338,0.978 3.686,1.126 0.348,0.149 10 BAT 3.177,1.281 3.272,1.425 0.095,0.144 10 2 3.338,1.37 3.686,1.518 0.348,0.149 10 ESS 2.938,1.754 3.208,1.907 0.270,0.153 10 F30 2.941,1.931 4.761,2.260 1.819,0.329 10 Steering Angle Sensor (Spiral Cable Sub-assembly) 5.107,1.718 6.815,2.060 1.709,0.342 10 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering sensor from the spiral cable.

·

When replacing the spiral cable, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>U0073).

·

When the speed sensor or the yaw rate sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral cable sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral cable sub-assembly), inspect and repair the speed sensor and yaw rate sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral cable sub-assembly).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.
U158310E01
0.163,0.094 0.381,0.284 0.218,0.191 10 *a 0.396,1.049 0.671,1.223 0.275,0.174 10 F30 2.383,1.396 2.712,1.816 false 2.758,1.734 3.082,1.885 0.324,0.151 10 BAT

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the steering angle sensor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F30-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.
U158311E01
0.163,0.094 0.381,0.284 0.218,0.191 10 *a 0.396,1.049 0.671,1.223 0.275,0.174 10 F30 2.139,1.396 1.817,1.808 false 1.588,1.734 1.790,1.885 0.202,0.151 10 IG

Remove the steering wheel and the column cover lower.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F30-5 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.
U126804E01
0.163,0.094 0.381,0.284 0.218,0.191 10 *a 0.396,1.049 0.702,1.201 0.306,0.151 10 F30 1.391,1.396 1.069,1.808 false 0.71,1.734 1.017,1.885 0.307,0.151 10 ESS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F30-2 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE)



Text in Illustration
*a Front view of wire harness connector
(to Steering angle sensor)

b.

Reconnect the steering angle sensor connector.


c.

Reinstall the steering wheel and the column cover lower.



OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)