Home › Brake › BRAKE (FRONT) › FRONT BRAKE › 2011.08–2014.07
RM19S0E _54 Brake _051477 BRAKE (FRONT) _0248245 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

C108932E06
1.958,1.375 1.125,1.906 1.125,1.906 2.073,1.448 false 0.938,1.823 1.115,2 0.177,0.177 10 false *a

a.

Align the matchmarks of the disc and axle hub and install the disc.

Text in Illustration
*a Matchmark

HINT:

When replacing the disc, select the position that gives the minimum disc runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the disc brake cylinder mounting onto the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C234680E01
0.338,1.885 0.572,2.034 0.234,0.15 10 *1

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new dust boots as shown in the illustration.

Text in Illustration
*1 Lithium Soap Base Glycol Grease

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bush dust boot.



b.

Install the 2 dust boots onto the disc brake cylinder mounting.


Hide 47715A 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.

Apply a light layer of lithium soap base glycol grease to the entire circumference of the slide pin (lower) as shown in the illustration.


b.

Install the slide bush onto the slide pin (lower).


c.
C234682E03
2.25,0.354 1.698,0.552 false 2.25,0.99 1.573,1.26 false 2.583,1.344 2.25,1.542 false 0.406,1.844 0.688,2.01 0.281,0.167 10 false *1 2.26,0.229 2.542,0.396 0.281,0.167 10 false *2 2.25,0.896 2.531,1.063 0.281,0.167 10 false *3 2.594,1.219 2.875,1.385 0.281,0.167 10 false *4

Apply a light layer of lithium soap base glycol grease to the entire circumference of the slide pins, as shown in the illustration.

Text in Illustration
*1 Lithium Soap Base Glycol Grease
*2 Slide Pin (Upper)
*3 Slide Pin (Lower)
*4 Slide bush


d.

Install the slide pin (upper) and slide pin (lower) onto the cylinder mounting.


Hide 5.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C234693E02
1.542,0.542 1.281,0.531 true 1.281,1.531 1.021,1.521 true 2.323,0.625 2.625,0.417 true 2.104,1.76 2.417,1.854 true 0.813,1.438 1.021,1.615 0.208,0.177 10 true *1 2.417,1.75 2.625,1.927 0.208,0.177 10 true *2 2.646,0.313 2.854,0.49 0.208,0.177 10 false *1 1.083,0.448 1.292,0.625 0.208,0.177 10 true *2

Install the 4 disc brake pad support plates onto the disc brake cylinder mounting.

Text in Illustration
*1 No. 1 Front Disc Brake Pad Support Plate
*2 No. 2 Front Disc Brake Pad Support Plate

NOTICE:

Be sure to install each pad support plate in the correct position and direction.



Hide 04945 6.INSTALL FRONT ANTI SQUEAL SHIM KIT

C243778E01
0.528,1.903 0.824,2.053 0.296,0.15 10 *1

a.

Apply disc brake grease to both sides of each No. 1 anti squeal shim.

Text in Illustration
*1 Disc Brake Grease

NOTICE:
·

When replacing worn pads, the anti squeal shims must be replaced together with the pads.

·

Install the shims in the correct positions and directions.

·

Apply disc brake grease to the area that contacts the anti squeal shims.

·

Disc brake grease can come out slightly from the area where the anti squeal shim is installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




b.
C243779E02
2.208,0.375 2.083,0.375 2.083,0.375 2.083,0.927 false 2.083,0.375 1.521,0.375 1.521,0.375 1.521,0.635 false 0.906,2.042 0.906,1.792 false 2.469,2.948 2.469,2.708 false 3.167,3.094 2.969,2.885 false 0.542,1.823 0.542,1.583 false 2.24,0.281 2.396,0.438 0.156,0.156 10 false *1 0.823,2.052 0.979,2.208 0.156,0.156 10 false *2 0.458,1.844 0.615,2 0.156,0.156 10 false *3 2.385,2.969 2.542,3.125 0.156,0.156 10 false *2 3.188,3 3.344,3.156 0.156,0.156 10 false *3

Install the 4 anti squeal shims onto each brake pad.

Text in Illustration
*1 Pad Wear Indicator Plate
*2 No. 1 Anti Squeal Shim
*3 No. 2 Anti Squeal Shim


c.

Install the pad wear indicator plates onto the upper side of the brake pads.


Hide 04465 7.INSTALL FRONT DISC BRAKE PAD KIT

a.

Install the 2 disc brake pads onto the disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



Hide 47750 8.INSTALL DISC BRAKE CYLINDER ASSEMBLY

a.

Hold the slide pin with a wrench and install the disc brake cylinder onto the disc brake cylinder mounting with the 2 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 47313A 9.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the flexible hose with a new union bolt and a new gasket.

Torque:
30 N*m (310 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



Hide 10.BLEED BRAKE LINE

Hide 11.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 12.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)