Home › Brake › BRAKE (REAR) › REAR BRAKE
RM19S0E _54 Brake _051478 BRAKE (REAR) _0248247 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  REASSEMBLY  


PROCEDURE

Hide 04474 1.INSTALL REAR WHEEL CYLINDER KIT

a.
C190260E02
0.405,3.001 2.416,3.161 2.011,0.160 10 *1

Apply lithium soap base glycol grease to 2 new wheel cylinder cups and the 2 pistons.

Text in Illustration
*1 Lithium Soap Base Glycol Grease


b.

Install the wheel cylinder cup onto each piston.


c.

Install the compression spring and 2 pistons onto the wheel brake cylinder.


d.

Install 2 new wheel cylinder boots onto the wheel brake cylinder.


Hide 47570 2.INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.

Install the wheel brake cylinder with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Using a union nut wrench 10 mm, install the brake tube.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 47547R 3.TEMPORARILY TIGHTEN REAR DRUM BRAKE BLEEDER PLUG

Hide 47548R 4.INSTALL REAR DRUM BRAKE BLEEDER PLUG CAP

Hide 47644A 5.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER

a.

Install the automatic adjust lever and automatic adjust lever tension spring onto the front brake shoe.


Hide 04495 6.INSTALL REAR BRAKE SHOE KIT

a.
C190261E02
0.462,2.961 2.016,3.135 1.554,0.173 10 *1

Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.

Text in Illustration
*1 High Temperature Grease


b.
C108972

Using needle-nose pliers, install the parking brake cable onto the parking brake shoe lever.


c.
C108971E03
1.74,1.583 2.094,1.698 false 2.135,1.646 2.844,1.948 0.708,0.302 10 false SST

Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


d.
C179336E03
0.444,1.711 2.010,1.853 1.566,0.142 10 *1

Apply high temperature grease to the adjusting bolt.

Text in Illustration
*1 High Temperature Grease


e.
F040013E09
1.667,0.406 1.281,0.76 false 1.75,1.24 1.625,1.729 false 1.667,0.271 1.885,0.469 0.219,0.198 10 false *1 1.521,1.729 1.698,1.927 0.177,0.198 10 false *2

Install the parking brake shoe strut set as shown in the illustration.

Text in Illustration
*1 Backing Plate
*2 Parking Brake Shoe Strut Set


f.
C108969E02
0.328,1.29 0.628,1.437 0.3,0.148 10 SST 1.744,1.374 0.678,1.374 false

Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

SST
09718-00011  


g.
F042698

Using needle-nose pliers, install the tension spring onto the front brake shoe and rear brake shoe.


h.
C108968E01
0.273,1.766 0.696,1.945 0.423,0.179 10 SST 0.648,1.841 1.157,1.602 false

Using SST, install the shoe return spring onto the front brake shoe.

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



Hide 7. CHECK REAR DRUM BRAKE INSTALLATION

a.

Check that each part is installed properly.

C241885E01
0.356,0 0.643,0.316 0.287,0.316 10 *a 3.921,0 4.209,0.316 0.287,0.316 10 *b

Text in Illustration
*a for LH Side *b for RH Side
V100135

Front of the Vehicle - -


b.
C116892

Measure the brake drum inner diameter and the diameter of the brake shoes. Check that the difference between the diameters is equal to the specified shoe clearance.

Shoe clearance:

0.6 mm (0.024 in.)


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.