Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2014.07
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / EMPS / DTC.


f.

According to the display on the tester, select the freeze frame data.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter/
Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) The vehicle is stopped
No significant fluctuation The vehicle is driven at a constant speed
Engine Revolution Engine revolution:
Min: 0 rpm
Max: 12800 rpm
Engine running at constant speed No significant fluctuation
Motor Actual Current Amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned
Command Value Current Demanded amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort The engine is running and the steering wheel is being turned
Thermistor Temperature ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
- Ignition switch is ON
PIG Power Supply Power source voltage to active motor/
Min.: 0.0000 V
Max.: 20.1531 V
11 to 14 V The engine is running and power steering is operating
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
11 to 14 V Ignition switch is ON
Steering Wheel Torque Steering wheel torque/
Min.: -7.00 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort The engine is running and power steering is in operation
Torque Sensor 1 Output Torque sensor 1 output voltage/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V The engine is running and the steering wheel is not turned (without load)
2.5 to 3.8 V The engine is running and the steering wheel is turned to the right when the vehicle is stopped
1.2 to 2.5 V The engine is running and the steering wheel is turned to the left when the vehicle is stopped
Torque Sensor 2 Output Torque sensor 2 output voltage/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V The engine is running and the steering wheel is not turned (without load)
1.2 to 2.5 V The engine is running and the steering wheel is turned to the right when the vehicle is stopped
2.5 to 3.8 V The engine is running and the steering wheel is turned to the left when the vehicle is stopped
TRQ1 Zero Point Value Torque sensor 1 zero point voltage/
Min.: 0.0000 V
Max.: 4.9725 V
Values differ depending on vehicle The engine is running and the steering wheel is not being turned
TRQ2 Zero Point Value Torque sensor 2 zero point voltage/
Min.: 0.0000 V
Max.: 4.9725 V
Values differ depending on vehicle The engine is running and the steering wheel is not being turned
Motor Terminal Volt (+) Motor terminal M1 voltage/
Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The engine is running and steering wheel turned to right
6 to 11 V The engine is running and steering wheel turned to left
Motor Terminal Volt (-) Motor terminal M2 voltage/
Min.: 0.0 V
Max.: 25.5 V
6 to 11 V The engine is running and steering wheel turned to right
11 to 14 V The engine is running and steering wheel turned to left
Stop&Start Ctrl Mode Status of the record of stop and start control mode/
IG, Run, Stopreq, Stop or Restart
- -
Current Key Cycle Number of times that the ignition switch was turned to ON since Assist Limit Record 1 was stored/
Min.: 0 times
Max.: 65535 times
- -
Current Key Cycle Elapsed Time Period of time that elapsed after Assist Limit Record 1 was stored before the ignition switch was turned to ON/
Min.: 0.0 s
Max.: 53687091.1 s
- -
Steering Angle Steering angle value/
Min.: -3072.0 deg
Max.: 3070.5 deg
- During steering operation: Changes in proportion with steering wheel rotation