Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No. DTC Detection Condition Trouble Area
C1551 Open or short in IG power source circuit with ignition switch ON.
·

ECU-IG NO. 1 fuse

·

IG power source circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C240045E02
0.802,0.719 2.188,1.042 1.385,0.323 10 false from IG1 NO. 1 Relay 2.542,0.885 3.479,1.115 0.938,0.229 10 false ECU-IG NO. 1 5.021,0.719 5.208,0.927 0.188,0.208 10 false F6 5.073,0.542 5.188,0.698 0.115,0.156 10 false 1 5.073,1.354 5.188,1.51 0.115,0.156 10 false 2 4.979,1.542 5.26,1.729 0.281,0.188 10 false A42 5.333,0.719 5.563,0.906 0.229,0.188 10 false IG 5.333,1.542 5.76,1.698 0.427,0.156 10 false PGND 4.698,2.115 6.667,2.365 1.969,0.25 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform the torque sensor zero point calibration and assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item IG Power Supply in the Data List and read the value displayed on the tester.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
11 to 14 V Ignition switch is ON



OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - IG CIRCUIT AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - IG CIRCUIT AND BODY GROUND)
a.
U126950E02
0.854,2.385 1.052,2.802 true 2.24,2.51 2.083,2.823 true 0.188,0.115 0.375,0.271 0.188,0.156 10 false *a 1.01,2.813 1.188,2.979 0.177,0.167 10 false IG 1.792,2.833 2.24,3 0.448,0.167 10 false PGND 0.677,1.771 0.917,1.948 0.24,0.177 10 false F6 2.302,1.771 2.594,1.927 0.292,0.156 10 false A42

Disconnect the power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F6-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY