Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TEST MODE PROCEDURE  


NOTICE:

The torque sensor zero point calibration is performed automatically when the test mode inspection is conducted after the power steering ECU has been replaced with a new one.


ENTER TEST MODE


a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / EMPS / Utility / Signal Check.



CHECK TEST MODE DISPLAY


a.
C342549E02
0.667,0.073 2.615,0.323 1.948,0.25 10 false EPS Warning Light Test Mode 0.24,0.792 1.25,0.979 1.01,0.188 10 false 0.125 seconds 2.021,0.792 2.99,0.99 0.969,0.198 10 false 0.125 seconds 0.583,1.031 0.896,1.229 0.313,0.198 10 false ON 0.573,1.396 0.885,1.594 0.313,0.198 10 false OFF 1.594,1.615 2.094,1.823 0.5,0.208 10 false (4 Hz)

The EPS warning light blinks as shown on the left when test mode is entered.

NOTICE:

If the torque sensor zero point calibration has not been performed, the EPS warning comes on until the torque sensor zero point calibration is completed, and shows the test mode blink pattern after the torque sensor zero point calibration is completed.




CHECK VEHICLE SPEED SIGNAL (w/o ABS)


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode code C1571 is stored during the transition to test mode. This code does not indicate a malfunction since the code will be cleared when the ECU determines that the sensor is normal.

·

The test mode code is cleared simultaneously when test mode is terminated.



a.

Drive the vehicle until the vehicle speed reaches 10 km/h (6 mph) or more.

C117900E12
0.49,0.104 2.302,0.365 1.813,0.26 10 false When system is normal: 1.896,0.698 2.833,0.906 0.938,0.208 10 false km/h (mph) 0.396,1.177 1.427,1.417 1.031,0.24 10 false Vehicle speed 2.115,1.208 2.604,1.396 0.49,0.188 10 false 10 (6) 2.146,1.781 2.448,1.948 0.302,0.167 10 false 0 0.354,2.438 1.563,2.698 1.208,0.26 10 false EPS Warning light 1.729,2.448 2.104,2.604 0.375,0.156 10 false ON 1.729,2.719 2.146,2.885 0.417,0.167 10 false OFF 2.469,2.875 3.26,3.094 0.792,0.219 10 false 4 Hz blink 3.292,2.875 6.24,3.26 2.948,0.385 10 false Light blinks until test mode code C1571 cleared. Light goes off at 10 km/h (6 mph) or more. 5.875,1.76 6.469,1.948 0.594,0.188 10 false Time



READ TEST MODE CODE


a.

Check the DTCs in test mode.

Test Mode DTC Test Signal Test Mode DTC Clear Condition Trouble areas
C1571 Vehicle speed check Vehicle speed 10 km/h (6 mph) or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

Vehicle speed signal circuit

·

Power steering ECU



NOTICE:

Test mode code is cleared when test mode is terminated.




END OF TEST MODE


a.

Return to normal mode by following the instructions on the tester screen.


b.

Turn the ignition switch off and disconnect the tester.