Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.08–2014.07
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1541  Vehicle Speed Signal Malfunction  C1542  Vehicle Speed Signal Malfunction  C1571  Speed Sensor Malfunction (Test Mode DTC)  


DESCRIPTION

Based on the vehicle speed signal received from the combination meter, the power steering ECU adjusts the amount of power assist according to vehicle speed. The power steering ECU monitors the speed signal input and stores a DTC if a malfunction is detected. While a malfunction exists in the vehicle speed signal, fail-safe operation maintains the amount of power assist at the level for a speed of 70 km/h (43 mph).

NOTICE:

Revving the engine while the vehicle is stopped may cause DTC C1541 or C1542 to be stored.


HINT:
·

If C1541 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more and then turning the ignition switch to off will clear the DTC.

·

If C1542 is stored while the vehicle is stopped, driving the vehicle for 5 minutes or more will clear the DTC.

·

These DTCs are only for vehicles without a skid control ECU (ABS ECU).

·

When the sensor is normal, a pulse signal (43 Hz at 37 mph [60 km/h]) that alternates between 0 V and 5 V is transmitted to the ECU.



DTC No. Detection Item Trouble Area
C1541 Vehicle Speed Signal Abnormal Increase
·

Speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


While vehicle stopped, engine rpm exceeds threshold* for 300 seconds or more, cumulative. -
C1542 Vehicle Speed Signal Abnormal Decrease
·

Speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


While vehicle stopped, engine rpm exceeds threshold* for 30 seconds or more, cumulative. -
C1571 Speed sensor malfunction (Test mode).
·

Speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly



*Threshold: An engine speed of 4000 rpm or greater is detected within 5 minutes after engine is started, or an engine speed of 2100 rpm or greater is detected 5 minutes or more after engine is started.

C225498E10
1.896,0.146 1.802,0.146 1.802,0.146 1.406,0.677 false 4.865,0.448 4.958,0.448 4.958,0.448 5.156,0.99 false 0.573,0.698 0.917,0.854 0.344,0.156 10 false 4000 0.573,1.031 0.927,1.188 0.354,0.156 10 false 2100 0.229,0.24 1.458,0.438 1.229,0.198 10 false Engine Speed (rpm) 0.844,1.469 0.948,1.625 0.104,0.156 10 false 0 2.385,1.51 3.042,1.677 0.656,0.167 10 false 5 minutes 1.948,0.073 4.458,0.271 2.51,0.198 10 false 30 seconds cumulative C1542 stored 2.5,0.375 5.083,0.583 2.583,0.208 10 false 300 seconds cumulative C1541 stored 4.333,1.51 6.24,1.708 1.906,0.198 10 false Elapsed time after engine start

WIRING DIAGRAM

C240044E01
0.318,1.79 2.192,1.958 1.874,0.168 10 Combination Meter Assembly 1.404,0.972 1.615,1.128 0.211,0.156 10 +S 1.74,0.986 1.926,1.136 0.186,0.150 10 F1 1.761,0.783 1.869,0.945 0.108,0.162 10 6 5.237,0.986 5.424,1.136 0.186,0.150 10 F6 5.273,0.783 5.380,0.945 0.108,0.162 10 2 5.524,0.985 5.859,1.150 0.335,0.165 10 SPD 4.92,1.798 6.897,1.942 1.977,0.144 10 Power Steering ECU Assembly 3.614,1.509 4.621,1.678 1.007,0.168 10 to Other ECUs

CAUTION / NOTICE / HINT

HINT:

Confirm that DTC C1571 has been cleared by activating test mode after the repair is completed.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (METER VEHICLE VELOCITY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / EMPS / Data List / Meter Vehicle Velocity.


e.

Drive the vehicle.


f.

Read the value displayed on the tester.

OK:

Vehicle speeds displayed on tester and speedometer display are equal.




OK

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)