Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for LHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248256 STEERING COLUMN ASSEMBLY(for LHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for LHD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL POWER STEERING MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness and tilt steering support bond cable of the power steering motor assembly.

·

Do not allow any moisture to come into contact with the power steering motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign objects to contaminate the power steering motor assembly.



C243731

a.

Apply grease to the serrated part of the electric power steering column sub-assembly.

NOTICE:

First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering motor assembly or electric power steering column sub-assembly.



b.

Temporarily install the power steering motor assembly to the electric power steering column sub-assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.



c.
C241871E01
0.612,0.937 0.773,1.106 0.161,0.170 10 *1 0.79,1.031 1.237,1.325 false

Secure the steering column assembly in a vise using aluminum plates.

Text in Illustration
*1 Wooden Block

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Secure the power steering motor assembly so that it is directly upright.

·

Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.




d.
C241872E01
0.48,0.991 0.712,1.191 0.232,0.200 10 *1 0.677,1.081 1.252,1.321 false 0.451,0.582 0.749,0.773 0.298,0.191 10 SST 0.799,0.67 1.761,1.209 false

Using SST, turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis centering of the power steering motor assembly.

SST
09616-00011  

Text in Illustration
*1 Wooden Block


e.

Tighten the 2 bolts.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


f.
C241873E01
0.374,1.117 0.529,1.302 0.155,0.184 10 *1 0.545,1.212 1.186,1.338 false 0.426,0.73 0.783,0.872 0.357,0.142 10 SST 0.787,0.831 1.761,1.209 false

Using SST, measure the turning torque of the steering main shaft.

SST
09616-00011  

Text in Illustration
*1 Wooden Block

Torque:
Turning torque : 1.45 N*m (14.8 kgf*cm, 12.8 in.*lbf)

or less


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the torque is not as specified, readjust the axis centering of the power steering motor assembly.


g.

Install a new clamp and tape to the wire harness as shown in the illustration.

C241874E03
6.771,2.115 6.948,1.969 false 6.771,2.656 6.948,2.802 false 5.458,2.354 5.667,2.125 false 4.479,2.344 4.677,2.125 false 3.323,1.354 3.552,1.656 false 2.583,1.333 2.823,1.646 false 3.708,1.521 3.948,1.927 false 6.948,1.854 7.115,2.021 0.167,0.167 10 false *1 6.969,2.74 7.135,2.906 0.167,0.167 10 false *2 5.688,2.01 5.854,2.177 0.167,0.167 10 false *3 4.688,2.01 4.854,2.177 0.167,0.167 10 false *4 3.177,1.219 3.344,1.385 0.167,0.167 10 false *5 2.427,1.24 2.594,1.406 0.167,0.167 10 false *5 4.938,1.25 5.104,1.417 0.167,0.167 10 false *a 3.969,1.896 4.135,2.063 0.167,0.167 10 false *f 5.875,1.458 6.042,1.625 0.167,0.167 10 false *b 5.875,2.833 6.042,3 0.167,0.167 10 false *c 4.156,2.833 4.323,3 0.167,0.167 10 false *d 3.135,2.677 3.302,2.844 0.167,0.167 10 false *e 5.333,2.396 5.5,2.563 0.167,0.167 10 false A 3.49,2.01 3.604,2.177 0.115,0.167 10 false B 2.813,2.01 2.927,2.177 0.115,0.167 10 false B

Text in Illustration
*1 Torque Sensor Wire Harness *2 Power Steering Motor Wire Harness
*3 Tape A *4 Clamp
*5 Tape B - -
*a 383 to 403 mm *b 100 mm
*c 80 to 100 mm *d 155 to 175 mm
*e 74 to 94 mm *f 10 mm

NOTICE:
·

Wrap the tape around the area marked as "A" in the illustration more than 1.5 times.

·

Wrap the tape around the area marked as "B" in the illustration more than 2 times.

·

As heat from the power steering motor assembly may generate smoke, use heat resistant tape (resistant to 100°C (212°F) or more).




Hide 84450 2.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY

a.

Engage the 2 claws to install the ignition or starter switch assembly onto the upper steering column bracket assembly.


Hide 85432 3.INSTALL KEY INTER LOCK SOLENOID (for Automatic Transaxle)

a.

Install the key inter lock solenoid onto the upper steering column bracket assembly with the screw.


Hide 84052 4.INSTALL UN-LOCK WARNING SWITCH ASSEMBLY

C233276

a.

Engage the 2 claws to install the un-lock warning switch assembly onto the upper steering column bracket assembly.

HINT:

Slide the un-lock warning switch assembly, in the direction shown by the arrow in the illustration, to install it.



Hide 5.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.
C233277

Turn the ignition switch to ACC.


b.

Install the ignition switch lock cylinder assembly into the upper steering column bracket assembly.


c.

Make sure that the ignition switch lock cylinder assembly is securely fixed onto the ignition switch lock cylinder assembly.


Hide 45280A 6.INSTALL UPPER STEERING COLUMN BRACKET ASSEMBLY

a.

Set the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C233278

Install the steering column upper with switch bracket assembly with a new steering lock set bolt, and then tighten the bolt until its head comes off.


Hide 45832 7.INSTALL TILT STEERING SUPPORT BOND CABLE

a.

Install the tilt steering support bond cable with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 45260 8.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.

HINT:
C236078E01
0.926,0.678 1.078,0.825 0.151,0.147 10 *a 1.114,0.758 1.666,0.758 false 0.845,0.992 0.996,1.138 0.151,0.147 10 *b 1.033,1.072 1.515,1.072 false

When either the steering column assembly or the No. 2 steering intermediate shaft assembly is replaced with a new one, they have no matchmarks, so align the marking (pink) on the steering column assembly shaft with the slit of the No. 2 steering intermediate shaft assembly, and install them.


Text in Illustration
*a Marking (Pink)
*b Slit


Hide 45209 9.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525E01
2.519,0.661 2.687,0.815 0.168,0.154 10 *a 1.933,0.747 2.494,0.747 2.494,0.747 1.893,0.894 false

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with the bolt.

Text in Illustration
*a Matchmark