Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248257 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  DISASSEMBLY  


PROCEDURE

Hide 45209 1.REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525E01
2.519,0.661 2.687,0.815 0.168,0.154 10 *a 1.933,0.747 2.494,0.747 2.494,0.747 1.893,0.894 false

Place matchmarks on the steering intermediate shaft assembly and the steering sliding yoke.

Text in Illustration
*a Matchmark


b.

Remove the bolt and the steering sliding yoke from the steering intermediate shaft assembly.


Hide 45260 2.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Remove the bolt and the No. 2 steering intermediate shaft assembly from the steering column assembly.


Hide 45832 3.REMOVE TILT STEERING SUPPORT BOND CABLE

a.

Remove the 2 screw and the tilt steering support bond cable.


Hide 45280A 4.REMOVE UPPER STEERING COLUMN BRACKET ASSEMBLY

a.

Fix the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a drill, drill a hole in the steering lock set bolt, to insert a screw extractor.


c.
C232526

Using the screw extractor, remove the steering lock set bolt and the upper steering column bracket assembly.


Hide 84052 5.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY

a.

Insert the key.


b.
C232527

Remove the un-lock warning switch assembly by releasing the 2 claws.

HINT:

Slide the un-lock warning switch assembly, in the direction shown by the arrow in the illustration, to remove it.



Hide 85432 6.REMOVE KEY INTER LOCK SOLENOID (for Automatic Transaxle)

a.
C232530

Remove the screw and key inter lock solenoid from the upper steering column bracket assembly.


Hide 7.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch to ACC.


b.
C245529E03
2.188,0.354 2.063,0.354 2.063,0.354 2.063,0.625 true 2.583,0.969 2.458,0.969 2.458,0.969 2.188,0.677 true 0.146,2.594 0.458,2.771 0.313,0.177 10 false ACC 0.458,3.094 0.865,3.271 0.406,0.177 10 false LOCK 2.219,0.271 2.375,0.417 0.156,0.146 10 false *1 2.615,0.896 2.771,1.042 0.156,0.146 10 false *2

Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly, as shown in the illustration, and pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the upper steering column bracket assembly.

Text in Illustration
*1 Claw
*2 Stopper
V100135

Push
V100136

Pull

NOTICE:

Pull the ignition switch lock cylinder assembly out until the claw comes into contact with the stopper of the upper steering column bracket assembly. Otherwise, the following procedure cannot be conducted properly.



c.
C232529E02
0.396,0.406 0.469,0.406 0.469,0.406 0.542,0.552 true 0.406,0.896 0.479,0.896 0.479,0.896 0.479,0.656 true 0.729,0.927 0.604,0.927 0.604,0.927 0.604,0.688 true 2.292,0.396 2.208,0.396 2.208,0.396 2.188,0.521 true 0.74,0.823 0.896,0.969 0.156,0.146 10 false *b 2.302,0.313 2.458,0.458 0.156,0.146 10 false *a 0.219,0.313 0.375,0.458 0.156,0.146 10 false *1 0.219,0.823 0.375,0.969 0.156,0.146 10 false *2

Insert the tip of a screwdriver into the hole in the steering column bracket and tilt it downward, as shown in the illustration, to disengage the claw on the ignition switch lock cylinder. Then pull out the ignition switch lock cylinder.

Text in Illustration
*1 Claw
*2 Stopper
*a Claw disengaged
*b Driver Insertion Hole
V100135

Tilt
V100136

Pull out


Hide 84450 8.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY

a.
C235441

Disengage the 2 claws and remove the ignition or starter switch assembly from the upper steering column bracket assembly.

NOTICE:
·

Be sure to start operation while the ignition or starter switch assembly faces upward, and while the upper steering column bracket assembly faces downward.

·

Check the press in condition of the arrow inner part. If the inner part has loose fit, replace the upper steering column bracket assembly.




Hide 45874B 9.REMOVE NO. 1 STEERING COLUMN PROTECTOR (for Manual Transaxle)

a.

Remove the bolt and No. 1 steering column protector.


Hide 10.REMOVE POWER STEERING MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness and tilt steering support bond cable of the power steering motor assembly.

·

Do not allow any moisture to come into contact with the power steering motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign objects to contaminate the power steering motor assembly.



a.
C234879

Cut the No. 1 clamp and remove it from the steering column assembly.


b.
C234663

Disengage the No. 2 clamp and separate the wire harness from the protector.


c.
C235438

Disengage the clamp and remove the protector.


d.
C243854E01
1.178,1.336 1.333,1.493 0.155,0.157 10 *2 1.257,1.158 1.257,1.34 false 1.772,1.336 1.927,1.493 0.155,0.157 10 *1 1.851,1.158 1.851,1.34 false 0.958,1.562 1.113,1.719 0.155,0.157 10 *3 1.037,1.158 1.037,1.566 false 1.46,1.562 1.615,1.719 0.155,0.157 10 *4 1.538,1.158 1.538,1.566 false

Cut the No. 2 clamp and No. 3 clamp, and remove the 2 clamps and the 2 pieces of tape from the wire harness.

Text in Illustration
*1 No. 2 clamp
*2 No. 3 clamp
*3 Tape A
*4 Tape B

NOTICE:

When removing the clamps and the tape, be careful not to damage the wire harness.



e.
C241870

Remove the 2 bolts and power steering motor assembly from the electric power steering column sub-assembly.