Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248257 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL POWER STEERING MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness and tilt steering support bond cable of the power steering motor assembly.

·

Do not allow any moisture to come into contact with the power steering motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign objects to contaminate the power steering motor assembly.



a.
C234657

Apply grease to the serrated part of the electric power steering column sub-assembly.

NOTICE:

First wipe off the existing grease from the serrated part, and then apply the dedicated grease supplied with a new power steering motor assembly or electric power steering column sub-assembly.



b.

Temporarily install the power steering motor assembly to the electric power steering column sub-assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.



c.
C234658E01
0.115,0.923 0.340,1.137 0.225,0.215 10 *1 0.308,1.017 0.991,1.365 false

Secure the steering column assembly in a vise using aluminum plates and a piece of cloth.

Text in Illustration
*1 Wooden Block

NOTICE:
·

Do not overtighten the vise, as the steering column assembly may become deformed.

·

Secure the power steering motor assembly so that it is directly upright.

·

Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.




d.
C234659E01
0.536,1.196 0.845,1.343 0.309,0.146 10 SST 0.905,1.277 1.539,1.277 false

Using SST, turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis centering of the power steering motor assembly.

SST
09616-00011  


e.

Tighten the 2 bolts.

Torque:
19 N*m (189 kgf*cm, 14 ft.*lbf)


f.
C234660E01
0.389,1.191 0.687,1.336 0.298,0.144 10 SST 0.748,1.27 1.536,1.27 false

Using SST, measure the turning torque of the steering main shaft.

SST
09616-00011  

Torque:
Turning torque : 1.45 N*m (14.8 kgf*cm, 12.8 in.*lbf)

or less


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the torque is not as specified, readjust the axis centering of the power steering motor assembly.


g.

Install 2 new clamps and tape to the wire harness as shown in the illustration.

C234661E02
0.328,1.739 0.522,1.894 0.193,0.154 10 *1 2.094,2.359 2.287,2.514 0.193,0.154 10 *3 0.328,2.471 0.522,2.625 0.193,0.154 10 *2 1.996,1.075 2.190,1.230 0.193,0.154 10 *a 2.483,1.284 2.677,1.438 0.193,0.154 10 *b 2.718,1.475 2.911,1.629 0.193,0.154 10 *c 1.401,1.475 1.595,1.629 0.193,0.154 10 *d 1.996,2.83 2.190,2.984 0.193,0.154 10 *e 1.401,2.646 1.595,2.800 0.193,0.154 10 *f 0.506,1.816 0.792,2.023 false 0.506,2.548 0.96,2.641 false 1.891,2.179 2.061,2.397 false 2.395,2.359 2.588,2.514 0.193,0.154 10 *4 2.199,2.187 2.362,2.397 false 2.772,2.359 2.965,2.514 0.193,0.154 10 *5 2.57,2.179 2.739,2.397 false 3.263,2.359 3.456,2.514 0.193,0.154 10 *6 3.061,2.179 3.23,2.397 false

Text in Illustration
*1 Power Steering Motor Wire Harness *2 Torque Sensor Wire Harness
*3 Tape A *4 No. 3 Clamp
*5 Tape B *6 No. 2 Clamp
*a 358 to 378 mm *b 152 to 168 mm
*c 60 to 100 mm *d 80 to 100 mm
*e 373 to 393 mm *f 105 mm

NOTICE:

Wrap the tape at least 1.5 turns.



h.
C234662

Pass the torque sensor wire harness through the cutout of a new protector.


i.
C235438

Engage the clamp and install the protector to the steering column assembly.

NOTICE:

Make sure the wire harness is not pinched between the protector and the steering column assembly.



j.
C234663

Engage No. 2 clamp and install the wire harness to the protector.


k.
C234664E01
2.431,1.386 2.545,1.528 0.114,0.142 10 A

Pass a new No. 1 clamp through the groove in the protector, and tighten it within area A shown in the illustration to secure the protector and wire harness to the power steering motor assembly.

NOTICE:

Make sure there is no rattling or looseness in the protector.


HINT:
·

Fastening power for No. 1 clamp: 200 N (20 kgf)

·

Coat the protector with paint.




l.

Cut off the excess length of No. 1 clamp.


Hide 45874B 2.INSTALL NO. 1 STEERING COLUMN PROTECTOR (for Manual Transaxle)

a.

Install the No. 1 steering column protector with the bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 84450 3.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY

a.

Engage the 2 claws to install the ignition or starter switch assembly onto the upper steering column bracket assembly.


Hide 85432 4.INSTALL KEY INTER LOCK SOLENOID (for Automatic Transaxle)

a.

Install the key inter lock solenoid onto the upper steering column bracket assembly with the screw.


Hide 84052 5.INSTALL UN-LOCK WARNING SWITCH ASSEMBLY

C233276

a.

Engage the 2 claws to install the un-lock warning switch assembly onto the upper steering column bracket assembly.

HINT:

Slide the un-lock warning switch assembly, in the direction shown by the arrow in the illustration, to install it.



Hide 6.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch to ACC.


b.
C233277

Install the ignition switch lock cylinder assembly into the upper steering column bracket assembly.


c.

Make sure that the ignition switch lock cylinder assembly is securely fixed onto the ignition switch lock cylinder assembly.


Hide 45280A 7.INSTALL UPPER STEERING COLUMN BRACKET ASSEMBLY

a.

Set the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C233278

Install the steering column upper with switch bracket assembly with a new steering lock set bolt, and then tighten the bolt until its head comes off.


Hide 45832 8.INSTALL TILT STEERING SUPPORT BOND CABLE

a.

Install the tilt steering support bond cable with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 45260 9.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.

HINT:
C236078E01
0.926,0.678 1.078,0.825 0.151,0.147 10 *a 1.114,0.758 1.666,0.758 false 0.845,0.992 0.996,1.138 0.151,0.147 10 *b 1.033,1.072 1.515,1.072 false

When either the steering column assembly or the No. 2 steering intermediate shaft assembly is replaced with a new one, they have no matchmarks, so align the marking (pink) on the steering column assembly shaft with the slit of the No. 2 steering intermediate shaft assembly, and install them.


Text in Illustration
*a Marking (Pink)
*b Slit


Hide 45209 10.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525E01
2.519,0.661 2.687,0.815 0.168,0.154 10 *a 1.933,0.747 2.494,0.747 2.494,0.747 1.893,0.894 false

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with the bolt.

Text in Illustration
*a Matchmark