Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2011.08–2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248261 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E234300E01
0.184,3.345 2.633,3.534 2.449,0.189 10 *2: w/o Automatic Light Control System 0.184,2.962 2.633,3.151 2.449,0.189 10 *1: w/ Automatic Light Control System 5.746,2.49 6.772,3.026 1.026,0.536 10 F107 Radio Receiver Assembly 5.816,0.666 6.265,0.821 0.449,0.154 10 ILL+ 5.816,1.88 6.265,2.035 0.449,0.154 10 GND1 0.604,0.666 1.415,0.821 0.811,0.154 10 from Battery 3.905,0.823 4.427,0.978 0.522,0.154 10 PANEL 2.312,1.403 2.761,1.558 0.449,0.154 10 TAIL 2.72,2.396 4.131,2.776 1.411,0.380 10 to Headlight Dimmer Switch Assembly*2 2.72,2.016 4.131,2.170 1.411,0.154 10 to Main Body ECU*1 5.593,1.78 5.772,1.965 0.179,0.186 10 7 5.551,0.566 5.730,0.751 0.179,0.186 10 10

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except radio receiver assembly. A
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). B



A

2.CHECK HARNESS AND CONNECTOR

B

2.CHECK HARNESS AND CONNECTOR
a.
U158653E02
2.177,1.26 2.333,1.729 true 1.635,1.271 1.635,1.74 true 0.146,0.104 0.333,0.333 0.188,0.229 10 false *a 2.25,1.75 2.875,1.958 0.625,0.208 10 false ILL+ 1.458,1.74 2.083,1.948 0.625,0.208 10 false GND1 1.573,0.354 1.917,0.51 0.344,0.156 10 false F107

Disconnect the F107 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F107-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F107-10 (ILL+) - Body ground Light control switch tail or head 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR