Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248261 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

OK:

The radio automatic station search function works properly.





OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components, such as a telephone antenna, are installed.

Result
Result Proceed to
Optional components are installed A
Optional components are not installed B

NOTICE:

Do not remove optional components without the permission of the customer.




A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

B

3.CHECK ANTENNA FOR NOISE PRODUCTION
3.CHECK ANTENNA FOR NOISE PRODUCTION
a.

With the ignition switch ACC, turn on the radio and select the AM mode.


b.

Remove the roof antenna pole sub-assembly.


c.

Place the tip of a screwdriver on the antenna and check that noise is heard from the speaker.

OK:

Noise occurs.



d.

Install the roof antenna pole sub-assembly.



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

4.CHECK INSTALLATION OF ANTENNA GROUND
4.CHECK INSTALLATION OF ANTENNA GROUND
a.

Check that the amplifier antenna ground is securely fastened to the body.

OK:

Ground is securely fastened to body.



b.

Check that the antenna cord sub-assembly ground is securely fastened to the body.

OK:

Ground is securely fastened to body.




OK

5.CHECK AMPLIFIER ANTENNA ASSEMBLY

NG

CORRECTLY INSTALL GROUND

5.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.
E229625E01
0.112,0.068 0.327,0.254 0.215,0.186 10 *a

Disconnect the amplifier antenna connectors.


b.

With the ignition switch ON, turn on the radio and select the AM mode.


c.

Place the tip of a screwdriver against the metal terminal of the No. 2 antenna cord sub-assembly and check that noise is heard from speakers.

OK:

Noise occurs.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 - Body ground During radio (AM) reception 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Amplifier Antenna Assembly)


e.

Reconnect the amplifier antenna connectors.



OK

REPLACE AMPLIFIER ANTENNA ASSEMBLY

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E170033E02
0.087,0.027 0.281,0.217 0.194,0.191 10 *a

Disconnect the No. 2 antenna cord sub-assembly connectors.


b.

With the ignition switch ACC, turn on the radio and select the AM mode.


c.

Place the tip of a screwdriver against the metal terminal of the No. 2 antenna cord sub-assembly and check that noise is heard from speakers.

OK:

Noise occurs.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 - Body ground During radio (AM) reception 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-Assembly)


e.

Reconnect the No. 2 antenna cord sub-assembly connectors.



OK

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK RADIO RECEIVER ASSEMBLY
7.CHECK RADIO RECEIVER ASSEMBLY
a.
E159266

Disconnect the antenna connector from the radio receiver assembly.


b.

With the radio receiver assembly connector connected, turn the ignition switch to ACC.


c.

Turn on the radio and select the AM mode.


d.

Place the tip of a screwdriver against the metal terminal of the radio receiver assembly and check that noise is heard from the speaker.

OK:

Noise occurs.



e.
E221708E01
0.184,0.069 0.493,0.336 0.309,0.267 10 *a

Reconnect the antenna connector to the radio receiver assembly.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 - Body ground During radio (AM) reception 11 to 14 V


Text in Illustration
*a Component with harness connected
(Radio Receiver Assembly)



OK

REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY