Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2011.08–2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248261 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.


for "Bluetooth":

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E231975E02
0.458,4.844 2.063,5.521 1.604,0.677 10 false F47 Radio Receiver Assembly 0.542,3.156 1.917,3.885 1.375,0.729 10 false B85 Speedometer Sensor 0.74,1.469 1.75,2.26 1.01,0.792 10 false A55 Brake Actuator Assembly 1.958,0.719 2.135,0.906 0.177,0.188 10 false 22 1.573,0.729 1.906,0.906 0.333,0.177 10 false SP1 1.26,7.25 2.875,7.51 1.615,0.26 10 false *2: w/o ABS 0.313,7.25 1.74,7.51 1.427,0.26 10 false *1: w/ ABS 5.375,3.135 6.563,3.844 1.188,0.708 10 false F1 Combination Meter Assembly 1.938,4.229 2.115,4.417 0.177,0.188 10 false 17 1.938,2.542 2.115,2.729 0.177,0.188 10 false 3 1.698,2.625 2.031,2.802 0.333,0.177 10 false SI 5.125,4.229 5.302,4.417 0.177,0.188 10 false 2 1.542,4.323 1.875,4.5 0.333,0.177 10 false SPD 5.333,4.323 5.667,4.5 0.333,0.177 10 false SPD 1.938,5.927 2.115,6.115 0.177,0.188 10 false 8 1.521,6.021 1.854,6.198 0.333,0.177 10 false SPD 5.125,2.542 5.302,2.729 0.177,0.188 10 false 6 5.344,2.625 5.677,2.802 0.333,0.177 10 false +S 5.125,0.719 5.302,0.906 0.177,0.188 10 false 5 5.344,0.792 5.677,0.969 0.333,0.177 10 false SI 3.24,6.031 3.521,6.188 0.281,0.156 10 false 3C 3.24,5.833 3.417,6.021 0.177,0.188 10 false 39 3.24,4.333 3.521,4.49 0.281,0.156 10 false 3A 3.24,4.135 3.417,4.323 0.177,0.188 10 false 16 0.927,6.552 1.292,7.208 0.365,0.656 10 false A74 ECM 4.5,2.646 4.781,2.802 0.281,0.156 10 false 3B 4.5,2.458 4.677,2.646 0.177,0.188 10 false 15 4.49,4.333 4.771,4.49 0.281,0.156 10 false 3A 4.51,4.146 4.688,4.333 0.177,0.188 10 false 37 5.333,4.854 6.635,5.583 1.302,0.729 10 false F6 Power Steering ECU Assembly 2.333,0.927 2.563,1.125 0.229,0.198 10 false *1 3.094,1.667 3.323,1.865 0.229,0.198 10 false *2 4.833,4.438 5.063,4.635 0.229,0.198 10 false *2

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U127333E06
1.938,1.417 2.573,1.156 true 1.177,4.094 1.406,4.292 0.229,0.198 10 false (A) 0.604,1.229 0.896,1.385 0.292,0.156 10 false F1 0.323,0.208 0.521,0.365 0.198,0.156 10 false *a 2.927,3.813 3.281,3.979 0.354,0.167 10 false GND 2.625,1.042 3.135,1.229 0.51,0.188 10 false 6(+S)

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminals F1-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F1-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approx. 20 km/h (12 mph)

Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

OK:

The waveform is displayed as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-17 (SPD) - F1-6 (+S) Always Below 1 Ω
F47-17 (SPD) - Body ground Always 10 kΩ or higher




OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR