Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248261 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the amplifier microphone assembly, and the amplifier microphone assembly sends microphone signals to the radio receiver assembly

WIRING DIAGRAM

E226275E14
0.906,3.458 2.354,4.135 1.448,0.677 10 false F95 Amplifier Microphone Assembly 5.188,3.458 6.344,4.5 1.156,1.042 10 false F47 Radio Receiver Assembly 4.927,2.281 5.104,2.469 0.177,0.188 10 false 18 4.927,1.792 5.104,1.979 0.177,0.188 10 false 19 5,2.781 5.177,2.969 0.177,0.188 10 false 6 5,1.302 5.177,1.49 0.177,0.188 10 false 5 2.083,1.292 2.26,1.479 0.177,0.188 10 false 2 2.083,1.781 2.26,1.969 0.177,0.188 10 false 3 2.083,2.76 2.26,2.948 0.177,0.188 10 false 4 5,0.813 5.177,1 0.177,0.188 10 false 4 2.083,0.823 2.26,1.01 0.177,0.188 10 false 1 5.219,0.875 5.667,1.031 0.448,0.156 10 false MACC 5.219,1.365 5.667,1.521 0.448,0.156 10 false MIN+ 5.219,2.354 5.667,2.51 0.448,0.156 10 false SGND 5.219,1.865 5.667,2.021 0.448,0.156 10 false MIN- 5.219,2.833 5.667,2.99 0.448,0.156 10 false SNS2 1.531,0.885 1.979,1.042 0.448,0.156 10 false MACC 1.531,1.396 1.979,1.552 0.448,0.156 10 false MCO+ 1.531,1.885 1.979,2.042 0.448,0.156 10 false MCO- 1.531,2.865 1.979,3.021 0.448,0.156 10 false SNS2 3.26,2.5 4,2.865 0.74,0.365 10 false (Shielded)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Disconnect the F95 amplifier microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-6 (SNS2) - F95-4 (SNS2) Always Below 1 Ω
F47-4 (MACC) - F95-1 (MACC) Always Below 1 Ω
F47-5 (MIN+) - F95-2 (MCO+) Always Below 1 Ω
F47-19 (MIN-) - F95-3 (MCO-) Always Below 1 Ω
F47-6 (SNS2) - Body ground Always 10 kΩ or higher
F47-4 (MACC) - Body ground Always 10 kΩ or higher
F47-5 (MIN+) - Body ground Always 10 kΩ or higher
F47-19 (MIN-) - Body ground Always 10 kΩ or higher
F47-18 (SGND) - Body ground Always 10 kΩ or higher



d.

Reconnect the amplifier microphone assembly connector.


e.

Reconnect the radio receiver assembly connector.



OK

2.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO RECEIVER ASSEMBLY
a.
U158535E01
1.584,0.603 1.864,0.784 0.280,0.181 10 F47 0.211,0.148 0.444,0.302 0.232,0.154 10 *a 2.655,2.703 3.100,2.857 0.445,0.154 10 SGND 2.641,0.724 3.086,0.877 0.445,0.154 10 MACC 1.889,2.703 2.237,2.857 0.348,0.154 10 MIN- 2.212,1.986 2.802,2.683 false 2.229,1.738 2.616,0.806 false 2.071,1.986 2.109,2.683 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F47-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F47-18 (SGND) - Body ground Always Below 1 Ω
F47-19 (MIN-) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Radio Receiver Assembly)


OK

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
a.
E228890E01
0.157,0.082 0.348,0.273 0.191,0.191 10 *a 1.725,1.762 2.138,1.930 0.412,0.167 10 MCO- 1.057,1.762 1.469,1.930 0.412,0.167 10 SNS2 1.519,1.254 1.302,1.762 false 1.657,1.254 1.917,1.762 false

Remove the amplifier microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SNS2) - 3 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Amplifier Microphone Assembly)



OK

4.CHECK AMPLIFIER MICROPHONE ASSEMBLY

NG

REPLACE AMPLIFIER MICROPHONE ASSEMBLY

4.CHECK AMPLIFIER MICROPHONE ASSEMBLY
a.
U158689E02
1.563,1.344 1.073,1.74 true 1.917,1.344 2.396,1.74 true 0.177,0.115 0.573,0.406 0.396,0.292 10 false *a 0.74,1.719 1.188,1.906 0.448,0.188 10 false MCO- 2.448,1.729 2.896,1.917 0.448,0.188 10 false MCO+ 1.646,0.271 1.927,0.427 0.281,0.156 10 false F95

Turn the ignition switch to ACC.


b.

Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-).


c.

Check the waveform of the amplifier microphone assembly using the oscilloscope.

Result
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output A
A waveform synchronized with the voice input to the map light assembly is not output B


Text in Illustration
*a Component with harness connected
(Amplifier Microphone Assembly)


A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE AMPLIFIER MICROPHONE ASSEMBLY