Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248274 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

B378032E04
0.969,0.729 1.74,1.073 0.771,0.344 10 false from Battery 3.031,0.896 3.5,1.073 0.469,0.177 10 false DOME 0.75,1.229 1.781,1.563 1.031,0.333 10 false from ACC Relay 0.427,1.688 1.792,1.99 1.365,0.302 10 false from IG1 NO. 1 Relay 3.052,1.365 3.521,1.542 0.469,0.177 10 false ACC 2.958,1.854 3.49,2.031 0.531,0.177 10 false GAUGE 5.323,0.51 5.448,0.667 0.125,0.156 10 false 4 5.323,1.01 5.448,1.188 0.125,0.177 10 false 3 5.313,1.49 5.438,1.667 0.125,0.177 10 false 1 5.344,2.094 5.469,2.271 0.125,0.177 10 false 7 5.615,0.74 6.146,0.896 0.531,0.156 10 false +B1 5.625,1.198 6.156,1.375 0.531,0.177 10 false ACC1 5.625,1.677 6.156,1.854 0.531,0.177 10 false IG 5.625,2.271 6.156,2.448 0.531,0.177 10 false GND1 5.563,2.917 6.802,3.604 1.24,0.688 10 false Radio and Display Receiver Assembly 5.208,2.302 5.552,2.458 0.344,0.156 10 false F125 5.208,1.688 5.552,1.844 0.344,0.156 10 false F127 5.198,1.219 5.542,1.375 0.344,0.156 10 false F125 5.198,0.74 5.542,0.896 0.344,0.156 10 false F125

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U158669E02
2.208,1.167 2.75,1.531 true 2,1.094 2.75,0.781 true 0.365,3.563 0.74,3.563 true 1.635,1.417 1.635,1.885 true 0.146,0.115 0.333,0.344 0.188,0.229 10 false *a 2.781,1.5 3.229,1.708 0.448,0.208 10 false +B1 2.781,0.646 3.229,0.854 0.448,0.208 10 false ACC1 0.167,3.49 0.792,3.698 0.625,0.208 10 false IG 1.448,1.917 2.073,2.125 0.625,0.208 10 false GND1 1.573,0.49 1.927,0.646 0.354,0.156 10 false F125 1.542,2.604 1.896,2.76 0.354,0.156 10 false F127

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F125-4 (+B1) - Body ground Always 11 to 14 V
F125-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F127-1 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR