Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248274 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch and the radio and display receiver assembly itself cannot function.

WIRING DIAGRAM

B378026E03
0.292,1.042 0.896,1.271 0.604,0.229 10 false Volume- 0.885,1.031 1.49,1.26 0.604,0.229 10 false Volume+ 1.656,1.042 2.125,1.271 0.469,0.229 10 false Seek- 2.25,1.052 2.719,1.281 0.469,0.229 10 false Seek+ 2.229,1.99 2.76,2.219 0.531,0.229 10 false MODE 0.792,3.99 1.438,4.219 0.646,0.229 10 false Off Hook 1.854,3.99 2.5,4.219 0.646,0.229 10 false On Hook 1.042,3.083 2.927,3.5 1.885,0.417 10 false Steering Pad Switch LH SIde 1.042,4.719 2.948,5.104 1.906,0.385 10 false Steering Pad Switch RH SIde 1.042,5.24 3.01,5.656 1.969,0.417 10 false Steering Pad Switch Assembly 4.729,0.625 5.083,0.854 0.354,0.229 10 false AU1 6.229,0.698 6.583,0.927 0.354,0.229 10 false SW1 6.229,1.74 6.635,1.969 0.406,0.229 10 false SWG 6.229,2.708 6.583,2.938 0.354,0.229 10 false SW2 4.729,2.646 5.083,2.875 0.354,0.229 10 false AU2 4.74,1.677 5.094,1.906 0.354,0.229 10 false EAU 4.271,0.531 4.49,0.719 0.219,0.188 10 false 10 5.927,0.646 6.156,0.833 0.229,0.188 10 false 21 5.927,1.667 6.156,1.854 0.229,0.188 10 false 23 5.927,2.625 6.156,2.813 0.229,0.188 10 false 22 4.313,1.563 4.531,1.75 0.219,0.188 10 false 8 5.333,1.563 5.552,1.75 0.219,0.188 10 false 4 5.333,0.521 5.552,0.708 0.219,0.188 10 false 6 5.333,2.521 5.552,2.708 0.219,0.188 10 false 5 4.313,2.521 4.531,2.708 0.219,0.188 10 false 9 4.26,0.74 4.531,0.927 0.271,0.188 10 false Z2 5.281,0.74 5.552,0.927 0.271,0.188 10 false F5 5.281,1.76 5.552,1.948 0.271,0.188 10 false F5 5.281,2.729 5.552,2.917 0.271,0.188 10 false F5 5.865,3.104 6.26,3.292 0.396,0.188 10 false F127 5.865,3.292 7.156,3.948 1.292,0.656 10 false Radio and Display Receiver Assembly 4.438,3.146 5.396,3.781 0.958,0.635 10 false Spiral Cable Sub-assembly 4.26,1.76 4.531,1.948 0.271,0.188 10 false Z2 4.26,2.719 4.531,2.906 0.271,0.188 10 false Z2

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEERING PAD SWITCH>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEERING PAD SWITCH>INSPECTION).



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the F127 radio and display receiver assembly connector.


b.

Disconnect the F5 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-21 (SW1) - F5-6 (AU1) Always Below 1 Ω
F127-22 (SW2) - F5-5 (AU2) Always Below 1 Ω
F127-23 (SWG) - F5-4 (EAU) Always Below 1 Ω
F127-21 (SW1) - Body ground Always 10 kΩ or higher
F127-22 (SW2) - Body ground Always 10 kΩ or higher
F127-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR