Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248274 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E226276E16
0.969,3.865 2.208,4.594 1.24,0.729 10 false No. 1 Stereo Jack Adapter Assembly 0.969,3.698 2.229,3.875 1.26,0.177 10 false F53 5.125,3.688 6.396,3.844 1.271,0.156 10 false F127 5.125,3.854 6.396,4.542 1.271,0.688 10 false Radio and Display Receiver Assembly 2.083,1.531 2.26,1.719 0.177,0.188 10 false 5 2.083,1.052 2.26,1.24 0.177,0.188 10 false 8 2.083,2.031 2.26,2.219 0.177,0.188 10 false 7 2.083,2.51 2.26,2.698 0.177,0.188 10 false 6 2.083,3 2.26,3.188 0.177,0.188 10 false 9 5.219,1.125 5.667,1.281 0.448,0.156 10 false ADPG 5.219,1.615 5.667,1.771 0.448,0.156 10 false VAR+ 5.219,2.594 5.667,2.75 0.448,0.156 10 false VAL+ 5.219,2.104 5.667,2.26 0.448,0.156 10 false VA- 5.219,3.073 5.667,3.229 0.448,0.156 10 false AGND 1.563,1.125 2.01,1.281 0.448,0.156 10 false AUXO 1.656,1.625 2.021,1.781 0.365,0.156 10 false ARO 1.563,2.125 2.01,2.281 0.448,0.156 10 false ASGN 1.667,2.615 2.031,2.771 0.365,0.156 10 false ALO 1.563,3.094 2.01,3.25 0.448,0.156 10 false AGND 3.344,3.271 4.083,3.635 0.74,0.365 10 false Shielded 4.948,3 5.125,3.188 0.177,0.188 10 false 11 4.948,2.51 5.125,2.698 0.177,0.188 10 false 28 4.948,2.021 5.125,2.208 0.177,0.188 10 false 27 4.948,1.531 5.125,1.719 0.177,0.188 10 false 26 4.948,1.042 5.125,1.229 0.177,0.188 10 false 25

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the F127 radio and display receiver assembly connector.


b.

Disconnect the F53 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-26 (VAR+) - F53-5 (ARO) Always Below 1 Ω
F127-28 (VAL+) - F53-6 (ALO) Always Below 1 Ω
F127-27 (VA-) - F53-7 (ASGN) Always Below 1 Ω
F127-25 (ADPG) - F53-8 (AUXO) Always Below 1 Ω
F127-11 (AGND) - F53-9 (AGND) Always Below 1 Ω
F127-26 (VAR+) - Body ground Always 10 kΩ or higher
F127-28 (VAL+) - Body ground Always 10 kΩ or higher
F127-27 (VA-) - Body ground Always 10 kΩ or higher
F127-25 (ADPG) - Body ground Always 10 kΩ or higher
F127-11 (AGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR