Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051483 AUDIO / VIDEO _0248274 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and amplifier microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when the microphone connection detection signal is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Amplifier microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E346360E01
1.708,0.688 2.323,0.885 0.615,0.198 10 false MIO- 1.667,1.51 2.281,1.708 0.615,0.198 10 false SNS2 0.979,2.021 1.438,2.219 0.458,0.198 10 false F95 0.979,2.188 2.292,2.792 1.313,0.604 10 false Amplifier Microphone Assembly 5.115,0.677 5.573,0.875 0.458,0.198 10 false MIN 5.094,1.49 5.708,1.688 0.615,0.198 10 false SNS2 5.042,2.021 5.656,2.219 0.615,0.198 10 false F127 5.042,2.167 6.448,2.792 1.406,0.625 10 false Radio and Display Receiver Assembly 4.813,0.594 5.125,0.792 0.313,0.198 10 false 19 4.885,1.385 5.042,1.583 0.156,0.198 10 false 6 2.156,0.594 2.281,0.771 0.125,0.177 10 false 3 2.167,1.396 2.323,1.594 0.156,0.198 10 false 4

PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U158704E02
2.083,1.25 2.229,1.667 true 0.063,0.031 0.219,0.198 0.156,0.167 10 false *a 0.167,0.406 0.531,0.552 0.365,0.146 10 false F127 2.125,1.688 2.469,1.823 0.344,0.135 10 false MIN-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
a.

Disconnect the F127 radio and display receiver assembly connector.


b.

Disconnect the F95 amplifier microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-6 (SNS2) - F95-4 (SNS2) Always Below 1 Ω
F127-19 (MIN-) - F95-3 (MIO-) Always Below 1 Ω
F127-6 (SNS2) - Body ground Always 10 kΩ or higher
F127-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
a.
E228890E16
0.157,0.082 0.348,0.273 0.191,0.191 10 *a 1.725,1.762 2.138,1.930 0.412,0.167 10 MIO- 1.057,1.762 1.469,1.930 0.412,0.167 10 SNS2 1.519,1.254 1.302,1.762 false 1.657,1.254 1.917,1.762 false

Remove the amplifier microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (SNS2) - 3 (MIO-) Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Amplifier Microphone Assembly)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE AMPLIFIER MICROPHONE ASSEMBLY