Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051484 NAVIGATION / MULTI INFO DISPLAY _0248277 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

B378032E05
0.99,0.708 1.771,0.885 0.781,0.177 10 false from Battery 3,0.875 3.469,1.052 0.469,0.177 10 false DOME 0.771,1.198 1.802,1.375 1.031,0.177 10 false from ACC Relay 0.448,1.677 1.813,1.854 1.365,0.177 10 false from IG1 NO. 1 Relay 3.063,1.354 3.531,1.531 0.469,0.177 10 false ACC 2.958,1.854 3.49,2.031 0.531,0.177 10 false GAUGE 5.323,0.521 5.448,0.677 0.125,0.156 10 false 4 5.302,0.969 5.427,1.146 0.125,0.177 10 false 3 5.323,1.458 5.448,1.635 0.125,0.177 10 false 1 5.313,2.063 5.438,2.24 0.125,0.177 10 false 7 5.635,0.74 6.167,0.896 0.531,0.156 10 false +B1 5.604,1.208 6.135,1.385 0.531,0.177 10 false ACC1 5.625,1.677 6.156,1.854 0.531,0.177 10 false IG 5.625,2.292 6.156,2.469 0.531,0.177 10 false GND1 5.51,2.958 6.813,3.323 1.302,0.365 10 false Navigation Receiver Assembly 5.198,2.292 5.542,2.448 0.344,0.156 10 false F130 5.208,1.688 5.552,1.844 0.344,0.156 10 false F132 5.188,1.208 5.531,1.365 0.344,0.156 10 false F130 5.208,0.729 5.552,0.885 0.344,0.156 10 false F130

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U158724E01
0.134,0.054 0.307,0.211 0.173,0.158 10 *a 2.51,1.023 2.895,1.181 0.385,0.158 10 +B1 0.629,1.367 1.070,1.524 0.441,0.158 10 GND1 0.376,0.739 0.764,0.897 0.389,0.158 10 F130 2.27,0.423 2.793,0.581 0.523,0.158 10 ACC1 2.129,0.843 2.481,1.066 false 1.953,0.771 2.239,0.523 false 1.615,1.051 1.122,1.4 false 0.576,2.607 0.965,2.765 0.389,0.158 10 IG 1.065,2.52 0.805,2.661 false 0.358,2.212 0.747,2.369 0.389,0.158 10 F132

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-4 (+B1) - Body ground Always 11 to 14 V
F130-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F132-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR