Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051484 NAVIGATION / MULTI INFO DISPLAY _0248277 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit.

The sound signal that has been sent is amplified by the navigation receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM

E226276E17
0.969,3.875 2.229,4.24 1.26,0.365 10 false No. 1 Stereo Jack Adapter Assembly 0.969,3.688 2.229,3.865 1.26,0.177 10 false F53 5.125,3.677 6.396,3.833 1.271,0.156 10 false F132 5.125,3.854 6.396,4.354 1.271,0.5 10 false Navigation Receiver Assembly 2.083,1.51 2.26,1.698 0.177,0.188 10 false 5 2.083,1.021 2.26,1.208 0.177,0.188 10 false 8 2.083,2.01 2.26,2.198 0.177,0.188 10 false 7 2.083,2.5 2.26,2.688 0.177,0.188 10 false 6 2.083,2.99 2.26,3.177 0.177,0.188 10 false 9 5.219,1.115 5.667,1.271 0.448,0.156 10 false ADPG 5.219,1.604 5.667,1.76 0.448,0.156 10 false VAR+ 5.219,2.604 5.667,2.76 0.448,0.156 10 false VAL+ 5.219,2.094 5.667,2.25 0.448,0.156 10 false VA- 5.219,3.073 5.667,3.229 0.448,0.156 10 false AGND 1.563,1.125 2.01,1.281 0.448,0.156 10 false AUXO 1.656,1.646 2.021,1.802 0.365,0.156 10 false ARO 1.563,2.135 2.01,2.292 0.448,0.156 10 false ASGN 1.667,2.635 2.031,2.792 0.365,0.156 10 false ALO 1.563,3.104 2.01,3.26 0.448,0.156 10 false AGND 3.344,3.26 4.083,3.625 0.74,0.365 10 false Shielded 4.948,2.99 5.125,3.177 0.177,0.188 10 false 11 4.948,2.5 5.125,2.688 0.177,0.188 10 false 28 4.948,2.01 5.125,2.198 0.177,0.188 10 false 27 4.948,1.51 5.125,1.698 0.177,0.188 10 false 26 4.948,1.031 5.125,1.219 0.177,0.188 10 false 25

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the F53 No. 1 stereo jack adapter assembly connector.


b.

Disconnect the F132 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-6 (ALO) - F132-28 (VAL+) Always Below 1 Ω
F53-5 (ARO) - F132-26 (VAR+) Always Below 1 Ω
F53-7 (ASGN) - F132-27 (VA-) Always Below 1 Ω
F53-9 (AGND) - F132-11 (AGND) Always Below 1 Ω
F53-8 (AUXO) - F132-25 (ADPG) Always Below 1 Ω
F53-6 (ALO) - Body ground Always 10 kΩ or higher
F53-5 (ARO) - Body ground Always 10 kΩ or higher
F53-7 (ASGN) - Body ground Always 10 kΩ or higher
F53-9 (AGND) - Body ground Always 10 kΩ or higher
F53-8 (AUXO) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR