Home › Power Source / Network › 2NZ-FE BATTERY / CHARGING › GENERATOR › from 2014.07
RM19S0E _57 Power Source / Network _051487 2NZ-FE BATTERY / CHARGING _0248283 GENERATOR A

2NZ-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A310415E01
1.073,1.24 0.458,0.333 0.458,0.333 1.104,0.854 true 2.563,0.521 2.823,0.354 2.823,0.354 2.677,0.75 false 0.146,0.24 0.604,0.438 0.458,0.198 10 false SST 2.906,0.25 3.24,0.448 0.333,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing to the generator end frame assembly until the bearing surface is level with the frame surface.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A329636E02
2.24,0.24 2.667,0.969 true 2.917,1.906 2.615,1.427 true 2.073,0.104 2.24,0.26 0.167,0.156 10 false *a 2.948,1.854 3.115,2.01 0.167,0.156 10 false *b

Fit the tabs on the retainer plate into the cutouts on the generator drive end frame assembly.

Text in Illustration
*a Tab
*b Cutout


c.

Install the retainer plate to the generator drive end frame assembly with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame assembly on the generator pulley.


b.
A310406

Install the generator rotor assembly to the generator drive end frame assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A310446E03
0.615,0.531 1.229,0.115 true 0.563,0.833 0.156,1.688 true 2.792,0.583 2.323,0.135 true 3.177,1.958 2.823,0.865 true 1.542,2.729 0.938,3.083 true 1.677,2.906 2.292,3.094 true 0.771,3.031 0.938,3.188 0.167,0.156 10 false *a 2.323,3.021 2.49,3.177 0.167,0.156 10 false *b 1.26,0.031 1.427,0.188 0.167,0.156 10 false *a 0.052,1.698 0.219,1.854 0.167,0.156 10 false *b 2.135,0.031 2.302,0.188 0.167,0.156 10 false *a 3.115,1.979 3.281,2.188 0.167,0.208 10 false *b

Install a new generator bearing cover packing to the generator coil assembly.

Text in Illustration
*a Protrusion
*b Groove

HINT:

Align the 3 protrusions of the generator bearing cover packing with the 3 grooves of the generator coil assembly when installing.



b.
A329635

Temporarily install the generator coil assembly to the generator drive end frame assembly with the 4 bolts.

NOTICE:

Because the alternator coil assembly must be installed with a press after the through bolts have first been temporarily tightened, do not attempt to install the generator coil assembly by tightening the through bolts only.



c.
A310417E02
1.344,0.448 0.802,0.323 false 2.854,0.281 2.688,0.49 false 0.5,0.25 0.844,0.417 0.344,0.167 10 false SST 2.906,0.188 3.25,0.354 0.344,0.167 10 false SST

Using SST and a press, slowly press the generator coil assembly to install it.

SST
09612-70100  (09612-07240)


d.

Tighten the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A310418E03
1.219,0.354 0.927,0.667 false 2.104,1.708 2.479,1.406 true 1.229,0.219 1.396,0.375 0.167,0.156 10 false *a 1.938,1.656 2.104,1.813 0.167,0.156 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the generator brush holder assembly hole.

Text in Illustration
*a 1.0 mm (0.0394 in.) Diameter Pin


b.
A310419

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.
A310420E03
1.74,0.615 2.74,0.302 true 2.771,0.198 3.01,0.396 0.24,0.198 10 false *a

Pull out the 1.0 mm (0.0394 in.) diameter pin from the generator brush holder assembly.

Text in Illustration
*a 1.0 mm (0.0394 in.) Diameter Pin
V100135

Pull Out


Hide 27387B 5.INSTALL GENERATOR TERMINAL INSULATOR

a.
A329632

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A329631

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 7.INSTALL GENERATOR PULLEY

a.

Secure the generator with regulator assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the generator pulley to the generator rotor assembly shaft by tightening the nut by hand.


c.
A329625E02
2.781,0.167 3.094,0.729 true 2.917,1.729 3.198,0.958 true 2.417,1.115 2.375,1.25 false 2.26,0.083 2.823,0.292 0.563,0.208 10 false SST1-B 2.396,1.667 2.969,1.865 0.573,0.198 10 false SST1-A 2.302,1.271 2.469,1.427 0.167,0.156 10 false *1

Install SST1-A and SST1-B to the generator rotor assembly shaft as shown in the illustration.

SST
09820-63011  (09820-06010)

Text in Illustration
*1 Generator Rotor Assembly Shaft


d.
A329626E03
2.208,0.969 2.25,0.875 false 1.833,0.167 2.885,0.479 true 3.104,0.719 2.896,1.333 true 1.292,0.094 1.833,0.281 0.542,0.188 10 false SST1-B 2.615,1.354 3.167,1.563 0.552,0.208 10 false SST1-A 2.135,0.979 2.302,1.135 0.167,0.156 10 false *1 2.104,3.073 2.323,3.271 0.219,0.198 10 false *a 1.219,2.333 1.385,2.49 0.167,0.156 10 true *b

Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

Text in Illustration
*1 Generator Rotor Assembly Shaft
*a Hold
*b Turn

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor assembly shaft.



e.
A329627E04
2.01,0.229 1.813,0.885 false 2.229,0.542 1.99,0.917 false 2.865,1.344 2.698,1.083 false 2.042,0.125 2.625,0.313 0.583,0.188 10 false SST1-B 2.271,0.427 2.823,0.604 0.552,0.177 10 false SST1-A 2.74,1.365 3.156,1.573 0.417,0.208 10 false SST2

Place SST2 to the nut.

SST
09820-63011  (09820-06021)

NOTICE:

Securely attach SST to the generator pulley and generator rotor assembly shaft.



f.
A329630E02
1.823,0.26 2.583,0.531 true 2.927,1 2.885,1.542 true 1.438,0.177 1.844,0.344 0.406,0.167 10 false SST2 2.604,1.573 3.177,1.74 0.573,0.167 10 false SST1-A 0.615,2.99 0.781,3.146 0.167,0.156 10 false *a 1.677,3.083 1.844,3.24 0.167,0.156 10 false *b

Using an adjustable wrench, tighten the nut by turning SST1-A in the direction shown in the illustration.

Text in Illustration
*a Hold
*b Turn

Torque:
133 N*m (1351 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



g.

Remove SST2 from the nut.


h.
A329629E03
1.792,0.25 2.885,0.479 true 3.146,0.719 2.938,1.396 true 1.25,0.167 1.771,0.333 0.521,0.167 10 false SST1-B 2.656,1.417 3.177,1.583 0.521,0.167 10 false SST1-A 2.208,3.073 2.417,3.292 0.208,0.219 10 false *a 1.385,2.948 1.594,3.156 0.208,0.208 10 false *b

Hold SST1-A, turn SST1-B in the direction shown in the illustration, and remove SST1-A and SST1-B from the generator rotor assembly shaft.

Text in Illustration
*a Hold
*b Turn


i.

Turn the generator pulley, and check that the generator pulley moves smoothly.


j.

Remove the generator with regulator assembly from the vise.


Hide 27446A 8.INSTALL CLAMP

a.
A329624

Install the clamp to the generator coil assembly with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)