Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › from 2014.07
RM19S0E _57 Power Source / Network _051488 POWER DISTRIBUTION _0248284 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


PROCEDURE

Hide 55303B 1.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 82141 2.SEPARATE INSTRUMENT PANEL WIRE

a.
E293620E02
1.146,1.115 0.615,0.833 true 2.073,0.521 1.677,0.875 true 2.656,2.375 2.094,2.615 true 2.104,0.438 2.323,0.635 0.219,0.198 10 true *a 0.385,0.719 0.563,0.938 0.177,0.219 10 true *b 2.677,2.26 2.865,2.469 0.188,0.208 10 true *a

Disengage the 2 clamps.

Text in Illustration
*a Clamp
*b Guide


b.

Remove the screw.


c.

Disengage the guide to separate the instrument panel wire.


Hide 82730 3.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
E293621

Disengage the clamp.


b.

Disconnect the connectors on the front side of the instrument panel junction block assembly.


c.

Disconnect the main body ECU connectors.


d.
E293622

Remove the 2 bolts.


e.
E293623E02
1.271,2.927 1.427,3.198 1.427,3.198 1.583,3.063 true 0.875,2.479 1.094,2.646 true 1.51,0.344 2.115,0.146 2.115,0.146 1.948,0.396 true 0.677,2.406 0.844,2.563 0.167,0.156 10 true *b 1.344,3.208 1.51,3.365 0.167,0.156 10 true *a 2.125,0.052 2.292,0.208 0.167,0.156 10 true *a

Disengage the 4 guides and hook to separate the instrument panel junction block assembly.

Text in Illustration
*a Guide
*b Hook


f.
E293624

Disconnect the back side connector as shown in the illustration.


g.
E288121E02
1.875,1.042 1.604,0.958 true 1.448,0.875 1.625,1.042 0.177,0.167 10 true *1

Slide the airbag lock upward.

Text in Illustration
*1 Airbag Lock


h.

Disconnect the back side connector as shown in the illustration.


i.

Remove the instrument panel junction block assembly.


Hide 89221 4.REMOVE MAIN BODY ECU

a.
E297321E01
0.069,1.949 0.239,2.110 0.170,0.161 10 *1 0.907,1.958 1.077,2.119 0.170,0.161 10 *2 1.763,1.755 1.933,1.916 0.170,0.161 10 *a 2.177,1.425 1.883,1.758 false 0.555,1.717 0.898,2.047 false 0.424,1.695 0.262,2.024 false

Release the lock on the junction block side.

Text in Illustration
*1 Main Body ECU
*2 Instrument Panel Junction Block
*a Protective Tape


b.

While pressing the lock on the junction block side, insert a screwdriver with its tip wrapped in protective tape between the main body ECU and the instrument panel junction block assembly.

NOTICE:

Use a thin-blade screwdriver with a diameter of 5.0 to 6.3 mm (0.197 to 0.248 in.), and with a length of 90 mm or more.



c.
E296072E01
1.681,1.718 1.851,1.878 0.170,0.161 10 *a 2.176,1.426 1.89,1.803 false

Do not pry the inserted screwdriver. Lift up the main body ECU to the point where the lock releases.

Text in Illustration
*a Protective Tape

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU.

·

If any terminals of the connectors, locking parts or cases are deformed or damaged, replace the instrument panel junction block assembly or the main body ECU.




d.
E296073

Remove the main body ECU by pulling it out from the junction block.

NOTICE:

Do not touch the main body ECU connector.