Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2011.08–2014.07
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) U

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR (for LHD)

U158583E01
5.634,1.269 5.969,0.851 false 5.634,1.479 5.969,1.896 false 6.036,0.743 6.814,0.928 0.779,0.185 10 CANH*e 6.027,1.662 6.852,1.847 0.824,0.185 10 CANL*d 6.027,1.887 6.852,2.072 0.824,0.185 10 CANL*e 1.646,0.336 1.920,0.504 0.274,0.168 10 A61 1.385,1.269 1.068,1.026 false 1.477,1.269 1.141,0.851 false 1.385,1.479 1.068,1.722 false 1.477,1.479 1.141,1.896 false 0.497,0.959 1.047,1.144 0.550,0.185 10 CANH*b 0.514,1.646 1.033,1.831 0.519,0.185 10 CANL*b 0.584,0.757 1.134,0.942 0.551,0.185 10 CANH*a 0.592,1.855 1.121,2.040 0.529,0.185 10 CANL*a 5.197,0.336 5.471,0.504 0.274,0.168 10 F82 5.826,1.278 6.071,1.227 false 5.826,1.483 6.071,1.508 false 6.041,0.964 6.921,1.149 0.879,0.185 10 CANH*d 6.111,1.174 6.991,1.359 0.879,0.185 10 CANH*c 6.117,1.439 6.996,1.624 0.879,0.185 10 CANL*c 5.541,1.269 5.884,0.669 false 5.541,1.479 5.884,2.079 false 5.938,0.507 6.746,0.692 0.808,0.185 10 CANH*f 5.92,2.091 6.855,2.260 0.935,0.168 10 CANL*f 5.706,1.276 6.016,1.049 false 5.699,1.467 6.002,1.722 false

Text in Illustration
*a to ECM *b to Skid Control ECU (Brake Actuator Assembly)
*c to Main Body ECU (Multiplex Network Body ECU) *d to Power Steering ECU Assembly
*e to DLC3 *f to No. 2 Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A61-9 (CANH) L ECM
A61-20 (CANL) W
A61-10 (CANH) G to Skid Control ECU (Brake Actuator Assembly)
A61-21 (CANL) W
F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU)
F82-12 (CANL) W
F82-2 (CANH) LG Power Steering ECU Assembly
F82-13 (CANL) W
F82-3 (CANH) GR DLC3
F82-14 (CANL) W
F82-4 (CANH) SB No. 2 Junction Connector
F82-15 (CANL) W


b.

NO. 1 JUNCTION CONNECTOR (for RHD)

U158584E03
1.385,1.292 1.073,1.042 false 1.479,1.302 1.146,0.885 false 1.406,1.479 1.094,1.719 false 1.5,1.479 1.167,1.896 false 5.792,1.313 6.042,1.26 false 5.802,1.479 6.052,1.51 false 5.51,1.302 5.854,0.698 false 5.51,1.49 5.854,2.094 false 1.646,0.354 1.917,0.521 0.271,0.167 10 false A61 0.521,0.958 1.073,1.146 0.552,0.188 10 false CANH*b 0.531,1.646 1.052,1.833 0.521,0.188 10 false CANL*b 0.604,0.76 1.156,0.948 0.552,0.188 10 false CANH*a 0.615,1.854 1.146,2.042 0.531,0.188 10 false CANL*a 5.198,0.354 5.469,0.521 0.271,0.167 10 false F82 6.115,1.167 6.99,1.354 0.875,0.188 10 false CANH*c 6.104,1.438 6.979,1.625 0.875,0.188 10 false CANL*c 5.927,0.563 6.74,0.75 0.813,0.188 10 false CANH*d 5.896,2.094 6.833,2.26 0.938,0.167 10 false CANL*d

Text in Illustration
*a to ECM *b to Skid Control ECU (Brake Actuator Assembly)
*c to Main Body ECU (Multiplex Network Body ECU) *d to No. 2 Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
A61-9 (CANH) L ECM
A61-20 (CANL) W
A61-10 (CANH) G to Skid Control ECU (Brake Actuator Assembly)
A61-21 (CANL) W
F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU)
F82-12 (CANL) W
F82-4 (CANH) SB No. 2 Junction Connector
F82-15 (CANL) W


c.

NO. 2 JUNCTION CONNECTOR (for LHD)

U158585E01
3.435,0.336 3.708,0.504 0.274,0.168 10 F83 3.174,1.269 2.856,1.026 false 3.174,1.479 2.856,1.722 false 2.281,0.945 2.831,1.130 0.550,0.185 10 CANH*d 2.31,1.66 2.830,1.845 0.519,0.185 10 CANL*d 3.778,1.269 4.121,0.669 false 3.778,1.479 4.121,2.079 false 4.172,0.589 4.980,0.774 0.808,0.185 10 CANH*a 3.35,1.269 2.894,0.782 false 2.312,0.706 3.120,0.891 0.808,0.185 10 CANH*c 4.172,2.003 5.107,2.172 0.935,0.168 10 CANL*a 3.355,1.479 2.938,2.004 false 2.385,1.921 2.948,2.089 0.563,0.168 10 CANL*c 3.45,1.269 3.027,0.544 false 2.446,0.453 3.254,0.638 0.808,0.185 10 CANH*b 3.444,1.479 3.079,2.205 false 2.508,2.152 3.443,2.320 0.935,0.168 10 CANL*b

Text in Illustration
*a to Airbag Sensor Assembly *b to Combination Meter Assembly
*c to Air Conditioning Amplifier Assembly*1 *d to No. 1 Junction Connector

Terminal No. (Symbol) Wiring Color Connect to
F83-4 (CANH) B Airbag Sensor Assembly
F83-15 (CANL) W
F83-7 (CANH) G Combination Meter Assembly
F83-18 (CANL) W
F83-8 (CANH) V Air Conditioning Amplifier Assembly*2
F83-19 (CANL) W
F83-10 (CANH) SB No. 1 Junction Connector
F83-21 (CANL) W

*1: w/ Cooler



d.

NO. 2 JUNCTION CONNECTOR (for RHD)

U158586E02
4.042,1.292 4.438,1.26 false 3.063,1.323 2.698,1.313 false 3.177,1.302 2.75,1.073 false 3.542,1.292 3.188,0.417 false 4.042,1.469 4.438,1.5 false 3.063,1.469 2.677,1.51 false 3.188,1.469 2.75,1.781 false 3.563,1.49 3.177,2.427 false 3.76,1.292 4.24,0.771 false 3.76,1.49 4.219,2.021 false 3.344,1.281 2.875,0.802 false 3.365,1.469 2.896,2.021 false 3.448,1.292 3.021,0.604 false 3.458,1.469 3.063,2.198 false 3.438,0.354 3.708,0.521 0.271,0.167 10 false F83 4.479,1.167 5.354,1.354 0.875,0.188 10 false CANH*a 4.479,1.427 5.354,1.615 0.875,0.188 10 false CANL*a 2.135,1.198 2.688,1.385 0.552,0.188 10 false CANH*g 2.125,1.448 2.646,1.635 0.521,0.188 10 false CANL*g 2.208,0.948 2.76,1.135 0.552,0.188 10 false CANH*f 2.219,1.729 2.74,1.917 0.521,0.188 10 false CANL*f 2.688,0.25 3.24,0.438 0.552,0.188 10 false CANH*c 2.677,2.396 3.208,2.583 0.531,0.188 10 false CANL*c 4.281,0.677 5.094,0.865 0.813,0.188 10 false CANH*b 2.365,0.698 3.177,0.885 0.813,0.188 10 false CANH*e 4.26,1.958 5.198,2.125 0.938,0.167 10 false CANL*b 2.385,1.948 3.323,2.115 0.938,0.167 10 false CANL*e 2.49,0.458 3.302,0.646 0.813,0.188 10 false CANH*d 2.542,2.156 3.479,2.323 0.938,0.167 10 false CANL*d

Text in Illustration
*a to Steering Angle Sensor (Spiral Cable Sub-assembly)*1 *b to Airbag Sensor Assembly
*c to Power Steering ECU Assembly *d to Combination Meter Assembly
*e to Air Conditioning Amplifier Assembly*2 *f to No. 1 Junction Connector
*g to DLC3 - -

Terminal No. (Symbol) Wiring Color Connect to
F83-1 (CANH) P Steering Angle Sensor (Spiral Cable Sub-assembly)*1
F83-12 (CANL) W
F83-4 (CANH) B Airbag Sensor Assembly
F83-15 (CANL) W
F83-6 (CANH) LG Power Steering ECU Assembly
F83-17 (CANL) W
F83-7 (CANH) G Combination Meter Assembly
F83-18 (CANL) W
F83-8 (CANH) V Air Conditioning Amplifier Assembly*2
F83-19 (CANL) W
F83-10 (CANH) SB No. 1 Junction Connector
F83-21 (CANL) W
F83-11 (CANH) GR DLC3
F83-22 (CANL) W

*1: w/ VSC

*2: w/ Cooler




CHECK DLC3


U126783E04
4.229,1.969 4.521,2.344 false 4.292,0.844 3.865,1.375 false 3,0.854 3.427,1.385 false 3.802,1.969 3.521,2.344 false 3.083,2.271 3.531,2.438 0.448,0.167 10 false CANL 4.375,0.75 4.823,0.917 0.448,0.167 10 false CANH 4.604,2.271 4.958,2.438 0.354,0.167 10 false BAT 2.75,0.771 3.104,0.938 0.354,0.167 10 false CG 3.51,0.729 3.802,0.885 0.292,0.156 10 false F4

a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F4-6 (CANH) - F4-14 (CANL) GR - W Ignition switch off 54 to 69 Ω
F4-6 (CANH) - F4-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F4-6 (CANH) - F4-4 (CG) GR - W-B Ignition switch off 200 Ω or higher
F4-14 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CHECK ECM


U158095E01
5.514,0.133 5.788,0.289 0.274,0.156 10 A74 2.25,0.133 2.524,0.289 0.274,0.156 10 B84 5.854,2.403 6.084,2.573 0.230,0.170 10 +B 5.154,2.403 5.564,2.573 0.411,0.170 10 CANH 1.651,2.403 1.869,2.573 0.218,0.170 10 E1 4.453,2.403 4.864,2.573 0.411,0.170 10 CANL 1.511,2.034 1.726,2.379 false 4.858,1.863 4.63,2.375 false 4.858,1.703 5.354,2.375 false 6.354,1.044 5.971,2.379 false

a.

Disconnect the A74 and B84 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A74-41 (CANH) - A74-49 (CANL) L - W Ignition switch off 108 to 132 Ω
A74-41 (CANH) - A74-2 (+B) L - B Ignition switch off 6 kΩ or higher
A74-49 (CANL) - A74-2 (+B) W - B Ignition switch off 6 kΩ or higher
A74-41 (CANH) - B84-104 (E1) L - W-B Ignition switch off 200 Ω or higher
A74-49 (CANL) - B84-104 (E1) W - W-B Ignition switch off 200 Ω or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


U158581E02
3.583,8.219 3.271,8.531 true 3.656,8.219 3.927,8.531 true 0.167,0.094 0.417,0.344 0.25,0.25 10 false *1 1.25,6.667 1.5,6.917 0.25,0.25 10 false *2 0.417,2.146 0.604,2.323 0.188,0.177 10 false 3E 0.948,2.146 1.125,2.323 0.177,0.177 10 false 3F 6.49,1.542 6.677,1.719 0.188,0.177 10 false 3A 6.49,0.938 6.677,1.115 0.188,0.177 10 false 3B 0.938,1.552 1.135,1.729 0.198,0.177 10 false 3C 0.938,0.948 1.135,1.125 0.198,0.177 10 false 3D 0.938,2.365 1.188,2.615 0.25,0.25 10 false *B 0.406,2.375 0.656,2.625 0.25,0.25 10 false *A 5.802,3.698 5.99,3.875 0.188,0.177 10 false 3E 6.344,3.688 6.521,3.865 0.177,0.177 10 false 3F 6.344,3.948 6.594,4.135 0.25,0.188 10 false *B 5.813,3.948 6.063,4.135 0.25,0.188 10 false *A 3.802,2.885 4.031,3.063 0.229,0.177 10 false MB 3.802,0.823 4.031,1 0.229,0.177 10 false MB 3.99,3.885 4.188,4.063 0.198,0.177 10 false 3C 1.51,3.875 1.708,4.052 0.198,0.177 10 false 3D 5.49,5.24 5.677,5.417 0.188,0.177 10 false 3A 1.635,5.24 1.823,5.417 0.188,0.177 10 false 3B 3.792,6.49 4.052,6.667 0.26,0.177 10 false F76 3.698,7.552 3.958,7.729 0.26,0.177 10 false F76 3.792,8.542 4.24,8.75 0.448,0.208 10 false CANL 3.063,8.563 3.51,8.771 0.448,0.208 10 false CANH

Text in Illustration
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)

a.

Disconnect the F76 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the 3B and 3C instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher



CHECK COMBINATION METER ASSEMBLY


U127243E02
4.323,1.156 4.063,1.552 false 3.385,1.156 3.125,1.552 false 4.479,1.156 4.74,1.552 false 5.646,1.156 5.906,1.552 false 4.458,0.333 4.75,0.49 0.292,0.156 10 false F1 3.625,1.479 4.177,1.635 0.552,0.156 10 false CANH 4.792,1.479 5.323,1.635 0.531,0.156 10 false CANL 2.979,1.479 3.229,1.635 0.25,0.156 10 false B 5.948,1.479 6.156,1.635 0.208,0.156 10 false ET

a.

Disconnect the F1 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F1-32 (CANH) - F1-31 (CANL) G - W Ignition switch off 108 to 132 Ω
F1-32 (CANH) - F1-40 (B) G - L Ignition switch off 6 kΩ or higher
F1-31 (CANL) - F1-40 (B) W - L Ignition switch off 6 kΩ or higher
F1-32 (CANH) - F1-21 (ET) G - W-B Ignition switch off 200 Ω or higher
F1-31 (CANL) - F1-21 (ET) W - W-B Ignition switch off 200 Ω or higher



CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


U158539E02
4.083,1.729 4.344,2.125 true 4.594,0.708 4.333,1.115 true 2.729,1.104 2.469,0.698 true 4.729,1.333 4.083,1.479 true 2.844,0.427 3.135,0.583 0.292,0.156 10 false A54 3.906,0.427 4.198,0.583 0.292,0.156 10 false A55 3.229,0.427 3.521,0.583 0.292,0.156 10 false *A 4.281,0.427 4.573,0.583 0.292,0.156 10 false *B 4.406,2.083 4.969,2.24 0.563,0.156 10 false CANH 4.781,1.25 5.323,1.406 0.542,0.156 10 false CANL 4.646,0.615 5.063,0.771 0.417,0.156 10 false GND1 2.156,0.625 2.573,0.781 0.417,0.156 10 false +BS

Text in Illustration
*A w/ VSC *B w/o VSC

a.

Disconnect the A54*1 or A55*2 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A54-25 (CANH) - A54-14 (CANL)*1
A55-25 (CANH) - A55-14 (CANL)*2
G - W Ignition switch off 54 to 69 Ω
A54-25 (CANH) - A54-12 (+BS)*1
A55-25 (CANH) - A55-12 (+BS)*2
G - W Ignition switch off 6 kΩ or higher
A54-14 (CANL) - A54-12 (+BS)*1
A55-14 (CANL) - A55-12 (+BS)*2
W - W Ignition switch off 6 kΩ or higher
A54-25 (CANH) - A54-1 (GND1)*1
A55-25 (CANH) - A55-1 (GND1)*2
G - W-B Ignition switch off 200 Ω or higher
A54-14 (CANL) - A54-1 (GND1)*1
A55-14 (CANL) - A55-1 (GND1)*2
W - W-B Ignition switch off 200 Ω or higher

*1: w/ VSC

*2: w/o VSC



CHECK AIRBAG SENSOR ASSEMBLY


U127348E01
0.044,0.456 0.221,0.596 0.177,0.140 10 *A 0.763,2.263 1.195,2.403 0.433,0.140 10 CANH 2.711,2.263 3.115,2.403 0.404,0.140 10 CANL 0.044,2.861 0.221,3.000 0.177,0.140 10 *B 1.936,1.594 1.211,2.319 false 2.283,1.941 2.661,2.319 false 5.961,3.272 6.261,3.412 0.300,0.140 10 BAT 6.626,2.95 6.248,3.328 false 5.272,1.858 5.571,1.998 0.300,0.140 10 CG 5.516,1.929 5.894,2.307 false 1.851,4.458 2.283,4.598 0.433,0.140 10 CANH 3.667,4.458 4.090,4.598 0.423,0.140 10 CANL 2.961,3.861 2.307,4.514 false 3.239,4.136 3.617,4.514 false 1.376,0.409 1.633,0.567 0.257,0.159 10 F16 5.971,1.838 6.219,1.996 0.248,0.159 10 F4 2.503,2.872 2.781,3.031 0.278,0.159 10 F16

Text in Illustration
*A w/o VSC *B w/ VSC

a.

Disconnect the F16 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F16-13 (CANH) - F16-22 (CANL) B - W Ignition switch off 54 to 69 Ω
F16-13 (CANH) - F4-16 (BAT) B - BE Ignition switch off 6 kΩ or higher
F16-22 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F16-13 (CANH) - F4-4 (CG) B - W-B Ignition switch off 200 Ω or higher
F16-22 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)


U127162E01
2.703,2.338 3.248,2.483 0.545,0.145 10 CANH 4.207,2.34 4.729,2.481 0.522,0.141 10 CANL 4.94,2.338 5.242,2.483 0.302,0.145 10 ESS 1.866,2.338 2.155,2.482 0.288,0.144 10 BAT 3.427,1.789 3.147,2.401 false 3.885,1.799 4.165,2.406 false 4.132,1.799 4.903,2.401 false 2.918,1.799 2.148,2.401 false 3.523,0.543 3.818,0.699 0.295,0.156 10 F30

a.

Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F30-4 (CANH) - F30-3 (CANL) P - W Ignition switch off 54 to 69 Ω
F30-4 (CANH) - F30-6 (BAT) P - SB Ignition switch off 6 kΩ or higher
F30-3 (CANL) - F30-6 (BAT) W - SB Ignition switch off 6 kΩ or higher
F30-4 (CANH) - F30-2 (ESS) P - BR Ignition switch off 200 Ω or higher
F30-3 (CANL) - F30-2 (ESS) W - BR Ignition switch off 200 Ω or higher



CHECK POWER STEERING ECU ASSEMBLY


U126895E01
4.531,0.726 4.826,0.882 0.295,0.156 10 A42 5.677,2.266 5.972,2.423 0.295,0.156 10 PIG 3.222,2.266 3.660,2.423 0.438,0.156 10 PGND 2.719,2.2 3.156,2.356 0.438,0.156 10 CANH 0.983,2.2 1.421,2.356 0.438,0.156 10 CANL 2.054,0.736 2.342,0.892 0.288,0.156 10 F6 5.079,1.634 5.632,2.327 false 4.236,1.634 3.669,2.327 false 2.128,1.574 2.681,2.267 false 1.96,1.574 1.393,2.267 false

a.

Disconnect the A42 and F6 power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) LG - W Ignition switch off 54 to 69 Ω
F6-7 (CANH) - A42-1 (PIG) LG - W Ignition switch off 6 kΩ or higher
F6-8 (CANL) - A42-1 (PIG) W - W Ignition switch off 6 kΩ or higher
F6-7 (CANH) - A42-2 (PGND) LG - W-B Ignition switch off 200 Ω or higher
F6-8 (CANL) - A42-2 (PGND) W - W-B Ignition switch off 200 Ω or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Cooler)


U127350E04
3.01,0.74 2.75,0.344 false 4.646,1.365 4.385,0.969 false 3.146,0.74 3.406,0.344 false 5.365,2.698 5.604,2.323 false 2.448,1.323 2.75,0.844 false 1.094,2.646 1.396,2.177 false 1.354,1.969 1.094,1.573 false 1.49,1.969 1.75,1.573 false 1.063,0.74 1.354,0.896 0.292,0.156 10 false F42 0.219,2.031 0.51,2.188 0.292,0.156 10 false F41 4.01,2.031 4.302,2.188 0.292,0.156 10 false F4 1.438,0.74 1.729,0.896 0.292,0.156 10 false *A 0.594,2.042 0.885,2.198 0.292,0.156 10 false *B 3.479,0.208 3.896,0.365 0.417,0.156 10 false TX+ 2.49,0.208 2.906,0.365 0.417,0.156 10 false TX- 2.125,1.26 2.542,1.417 0.417,0.156 10 false GND 4.698,1.323 5.115,1.479 0.417,0.156 10 false B 5.094,2.625 5.51,2.781 0.417,0.156 10 false BAT 0.771,2.604 1.188,2.76 0.417,0.156 10 false GND 1.792,1.448 2.208,1.604 0.417,0.156 10 false TX+ 0.865,1.448 1.281,1.604 0.417,0.156 10 false TX-

Text in Illustration
*A for Automatic Air Conditioning System *B for Manual Air Conditioning System (w/ Cooler)

a.

Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F42-11 (TX+) - F42-12 (TX-)*1
F41-8 (TX+) - F41-9 (TX-)*2
V - W Ignition switch off 54 to 69 Ω
F42-11 (TX+) - F42-21 (B)*1
F41-8 (TX+) - F4-16 (BAT)*2
V - BE Ignition switch off 6 kΩ or higher
F42-12 (TX-) - F42-21 (B)*1
F41-9 (TX-) - F4-16 (BAT)*2
W - BE Ignition switch off 6 kΩ or higher
F42-11 (TX+) - F42-14 (GND)*1
F41-8 (TX+) - F41-23 (GND)*2
V - W-B Ignition switch off 200 Ω or higher
F42-12 (TX-) - F42-14 (GND)*1
F41-9 (TX-) - F41-23 (GND)*2
W - W-B Ignition switch off 200 Ω or higher

*1: for Automatic Air Conditioning System

*2: for Manual Air Conditioning System (w/ Cooler)