Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2011.08–2014.07
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) D

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  DIAGNOSIS SYSTEM  


BUS CHECK (COMMUNICATION MALFUNCTION ECU)


Only CAN communication system DTCs for each ECU can be output to the intelligent tester.

a.
C128170

Select "Bus Check" from the "System Select" screen on the intelligent tester.


b.
C128171

Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".


c.
C128172

Select the system of the DTC to be checked and select "Details".


d.
C128173

CAN communication system DTCs are output.



BUS CHECK (COMMUNICATION BUS CHECK)


HINT:

The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.


a.
C128171

Select "Communication Bus Check" from the "Bus Check" screen.


b.

The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

HINT:
·

If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).

·
C197127

The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop-down list. The drop-down list displays "ALL", "V Bus" and the names of the remaining buses.

Combo Box Display Content
ALL All ECUs (sensors) connected to the CAN bus
V Bus ECUs (sensors) connected to the V Bus
Bus Name ECUs (sensors) connected to the selected bus

·

The connection status (shown below) is indicated by the background color displayed behind the system name.

ECU (Sensor) on V Bus
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Not displayed Has never been detected

ECU (Sensor) with no Data Monitor History
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Not displayed Has never been detected

ECU (Sensor) with Data Monitor History
Background Color Connection Status
White Detected normally
Yellow Could not be detected in the past, but is currently detected
Red Detected in the past, but cannot be detected now
Red Has never been detected but has connection history
Not displayed Has never been detected and has no connection history




c.
C128179

"There is no system connected the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.



CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION


a.

Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.

ECU/Sensor Name Tester Display Installed on
Air conditioning amplifier assembly Air Conditioning Amplifier w/ Cooler
Airbag sensor assembly Airbag All vehicles
Combination meter assembly Combination Meter All vehicles
ECM ECM (Engine) All vehicles
Main body ECU (multiplex network body ECU) Main Body All vehicles
Power steering ECU assembly Power Steering (EPS) All vehicles
Skid control ECU (brake actuator assembly) Skid Control (ABS/VSC/TRAC) All vehicles
Steering angle sensor (spiral cable sub-assembly) Spiral cable (Steering Angle Sensor) w/ VSC



DTC TABLE BY ECU


HINT:
·

In the CAN communication system, CAN communication system DTCs stored by the ECU can be output from the ECU by using the intelligent tester.

·

If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".



a.

ECM

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0129 Lost Communication with Brake System Control Module


b.

MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0100 Lost Communication With ECM/PCM "A"
U0101 Lost Communication with TCM
U0151 Lost Communication With Restraints Control Module
U0155 Lost Communication with Instrument Panel Cluster (IPC) Control Module
U0164 Lost Communication With HVAC Control Module


c.

SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (w/ VSC)

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0073 Control Module Communication Bus Off
U0100 Lost Communication With ECM/PCM "A"
U0123 Lost Communication with Yaw Rate Sensor Module
U0124 Lost Communication with Lateral Acceleration Sensor Module
U0126 Lost Communication with Steering Angle Sensor Module
U0142 Lost Communication with Body Control Module "B"


d.

SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (w/o VSC)

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0073 Control Module Communication Bus Off
U0142 Lost Communication with Body Control Module "B"


e.

POWER STEERING ECU ASSEMBLY

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0100 Lost Communication with ECM/PCM "A"
U0129 Lost Communication With Brake System Control Module


f.

COMBINATION METER ASSEMBLY

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0100 Lost Communication with ECM/PCM "A"
U0129 Lost Communication with Brake System Control Module
U0131 Lost Communication with Power Steering Control Module
U0151 Lost Communication with Restraints Control Module


g.

AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Cooler)

HINT:

DTC communication uses the CAN communication system.


DTC No. Detection Item
U0100 Lost Communication With ECM/PCM "A"
U0131 Lost Communication With Power Steering Control Module
U0142 Lost Communication With Body Control Module "B"
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module


h.

STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)

HINT:

The steering angle sensor (spiral cable sub-assembly) is connected to the CAN communication system but CAN communication DTCs are not stored.



i.

AIRBAG SENSOR ASSEMBLY

HINT:

The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.




DTC COMBINATION TABLE


HINT:
·

○: Stored.

·

X: When one side of the branch wire is open, storage may occur.

·

-: Not stored.

·

*1: During a communication stop, cannot be stored.



Output from Output DTC Detected Communication Stop Mode
V Bus
ECM Communication Stop Mode ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode Brake Actuator (Skid Control ECU) Communication Stop Mode
ECM U0129 ○*1 ○ ○
Skid control ECU (brake actuator assembly) (w/ VSC) U0073 X ○*1 X
U0100 ○ ○*1 X
U0123 X ○*1 X
U0124 X ○*1 X
U0126 X ○*1 X
U0142 X ○*1 X
Skid control ECU (brake actuator assembly) (w/o VSC) U0073 X X ○*1
U0142 X X ○*1
Air conditioning amplifier assembly U0100 ○ - -
U0131 - - -
U0142 - - -
U0155 - - -
Main body ECU (multiplex network body ECU) U0100 ○ - -
U0101 ○ - -
U0151 - - -
U0155 - - -
U0164 - - -
Power steering ECU assembly U0100 ○ - -
U0129 - ○ ○
Combination meter assembly U0100 ○ - -
U0129 - ○ ○
U0131 - - -
U0151 - - -

HINT:
·

○: Stored.

·

X: When one side of the branch wire is open, storage may occur.

·

-: Not stored.

·

*1: During a communication stop, cannot be stored.



Output from Output DTC Detected Communication Stop Mode
V Bus
Air Conditioning Amplifier Communication Stop Mode Center Airbag Sensor Communication Stop Mode Main Body ECU Communication Stop Mode
ECM U0129 - - -
Skid control ECU (brake actuator assembly) (w/ VSC) U0073 X X X
U0100 X X X
U0123 X ○ X
U0124 X ○ X
U0126 X X X
U0142 X X ○
Skid control ECU (brake actuator assembly) (w/o VSC) U0073 X X X
U0142 X X ○
Air conditioning amplifier assembly U0100 ○*1 - -
U0131 ○*1 - -
U0142 ○*1 - ○
U0155 ○*1 - -
Main body ECU (multiplex network body ECU) U0100 - - ○*1
U0101 - - ○*1
U0151 - ○ ○*1
U0155 - - ○*1
U0164 ○ - ○*1
Power steering ECU assembly U0100 - - -
U0129 - - -
Combination meter assembly U0100 - - -
U0129 - - -
U0131 - - -
U0151 - ○ -

HINT:
·

○: Stored.

·

X: When one side of the branch wire is open, storage may occur.

·

-: Not stored.

·

*1: During a communication stop, cannot be stored.



Output from Output DTC Detected Communication Stop Mode
V Bus
Power Steering ECU Communication Stop Mode Steering Angle Sensor Communication Stop Mode Combination Meter ECU Communication Stop Mode
ECM U0129 - - -
Skid control ECU (brake actuator assembly) (w/ VSC) U0073 X X X
U0100 X X X
U0123 X X X
U0124 X X X
U0126 X ○ X
U0142 X X X
Skid control ECU (brake actuator assembly) (w/o VSC) U0073 X X X
U0142 X X X
Air conditioning amplifier assembly U0100 - - -
U0131 ○ - -
U0142 - - -
U0155 - - ○
Main body ECU (multiplex network body ECU) U0100 - - -
U0101 - - -
U0151 - - -
U0155 - - ○
U0164 - - -
Power steering ECU assembly U0100 ○*1 - -
U0129 ○*1 - -
Combination meter assembly U0100 - - ○*1
U0129 - - ○*1
U0131 ○ - ○*1
U0151 - - ○*1

HINT:
·

○: Stored.

·

X: When one side of the branch wire is open, storage may occur.

·

-: Not stored.

·

*1: During a communication stop, cannot be stored.