Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2011.08–2015.06
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "Bus Check".


·

"ECM Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside ECM

·

ECM main wire or connector

·

ECM



WIRING DIAGRAM

E229246E05
5.979,0.781 6.406,0.948 0.427,0.167 10 false CANH 5.979,1.208 6.406,1.375 0.427,0.167 10 false CANL 2.688,0.667 2.896,0.833 0.208,0.167 10 false 9 2.667,1.115 2.875,1.281 0.208,0.167 10 false 20 5.677,1.021 6,1.188 0.323,0.167 10 false 49 5.677,0.583 6,0.75 0.323,0.167 10 false 41 5.635,1.208 6.042,1.375 0.406,0.167 10 false A74 5.635,0.781 6.042,0.948 0.406,0.167 10 false A74 6.229,6.167 6.563,6.479 0.333,0.313 10 false ECM 1.24,1.677 1.521,1.844 0.281,0.167 10 false A61 5.979,2.115 6.406,2.281 0.427,0.167 10 false BATT 2.74,2.135 4.031,2.469 1.292,0.333 10 false from EFI MAIN Fuse 2.698,2.677 4.031,2.99 1.333,0.313 10 false from EFI MAIN Relay 5.979,2.656 6.406,2.823 0.427,0.167 10 false +B 5.979,3.031 6.406,3.198 0.427,0.167 10 false +B2 1.24,1.833 2.844,2.156 1.604,0.323 10 false No. 1 Junction Connector 5.708,2.448 6,2.615 0.292,0.167 10 false 2 5.719,2.854 5.979,3.021 0.26,0.167 10 false 1 5.688,1.948 6,2.115 0.313,0.167 10 false 20 4.396,2.281 5.073,2.448 0.677,0.167 10 false EFI NO. 3 5.979,4.292 6.406,4.458 0.427,0.167 10 false ME01 5.698,4.104 6.01,4.271 0.313,0.167 10 false 43 5.646,4.292 6.052,4.458 0.406,0.167 10 false B84 5.979,4.708 6.406,4.875 0.427,0.167 10 false E01 5.698,4.531 5.979,4.708 0.281,0.177 10 false 45 5.635,4.708 6.042,4.917 0.406,0.208 10 false B84 5.979,3.438 6.406,3.604 0.427,0.167 10 false E1 5.656,3.24 6,3.406 0.344,0.167 10 false 104 5.646,3.438 6.052,3.604 0.406,0.167 10 false B84 5.979,3.865 6.406,4.031 0.427,0.167 10 false E02 5.698,3.677 6.01,3.844 0.313,0.167 10 false 44 5.646,3.865 6.052,4.031 0.406,0.167 10 false B84 5.979,5.177 6.406,5.344 0.427,0.167 10 false E03 5.688,4.99 5.969,5.177 0.281,0.188 10 false 86 5.646,5.177 6.01,5.365 0.365,0.188 10 false B84 5.979,5.615 6.406,5.781 0.427,0.167 10 false EC 5.688,5.427 6,5.594 0.313,0.167 10 false 32 5.615,5.615 6.021,5.781 0.406,0.167 10 false A74 5.646,1.677 6.052,1.844 0.406,0.167 10 false A74 5.979,1.667 6.406,1.833 0.427,0.167 10 false IGSW 3.083,1.667 4.052,2 0.969,0.333 10 false from IG2 Relay 5.677,1.49 5.99,1.656 0.313,0.167 10 false 28 4.604,1.833 4.875,2 0.271,0.167 10 false IG2 5.635,2.125 6.042,2.292 0.406,0.167 10 false A74 5.635,3.031 6.042,3.198 0.406,0.167 10 false A74 5.625,2.646 6.031,2.813 0.406,0.167 10 false A74

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM MAIN WIRE)
a.

Disconnect the A74 ECM connector.


b.
U158551E01
0.28,1.035 0.544,1.217 0.264,0.181 10 A74 0.057,0.038 0.227,0.198 0.170,0.161 10 *a 2.862,0.963 3.278,1.113 0.417,0.150 10 CANH 2.862,1.507 3.278,1.657 0.416,0.150 10 CANL 2.476,1.345 2.843,1.594 false 2.469,1.262 2.836,1.05 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A74-41 (CANH) - A74-49 (CANL) Ignition switch off 108 to 132 Ω



Text in Illustration
*a Front view of wire harness connector
(to ECM)


OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check for the ECM power source circuit (for 1NZ-FE) (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>ECM Power Source Circuit).


b.

Check for the ECM power source circuit (for 2NZ-FE) (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit).


Result
Result Proceed to
NG A
OK (for 1NZ-FE) B
OK (for 2NZ-FE) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

B

C