Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on "Bus Check".

·

"Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside airbag sensor assembly

·

Airbag sensor assembly branch wire or connector

·

Airbag sensor assembly



WIRING DIAGRAM

E229165E08
1.438,1.031 1.865,1.198 0.427,0.167 10 false CANH 1.438,1.521 1.917,1.719 0.479,0.198 10 false CANL 0.542,2.031 0.948,2.198 0.406,0.167 10 false F83 5,0.958 5.208,1.125 0.208,0.167 10 false 13 5.271,1.052 5.698,1.219 0.427,0.167 10 false CANH 5.271,1.5 5.698,1.667 0.427,0.167 10 false CANL 2.375,2.688 3.344,3 0.969,0.313 10 false from IG2 Relay 4.219,2.885 4.521,3.083 0.302,0.198 10 false IG2 5.271,3.24 5.698,3.406 0.427,0.167 10 false E1 5.271,3.521 5.698,3.688 0.427,0.167 10 false E2 5,1.406 5.208,1.573 0.208,0.167 10 false 22 1.969,0.958 2.146,1.146 0.177,0.188 10 false 4 1.927,1.396 2.115,1.583 0.188,0.188 10 false 15 5.271,2.708 5.698,2.875 0.427,0.167 10 false IG2 5,2.625 5.208,2.792 0.208,0.167 10 false 21 5,3.146 5.208,3.313 0.208,0.167 10 false 25 5,3.427 5.208,3.594 0.208,0.167 10 false 26 0.542,2.208 2.156,2.531 1.615,0.323 10 false No. 2 Junction Connector 4.948,3.885 5.333,4.052 0.385,0.167 10 false F16 4.948,4.052 6.521,4.688 1.573,0.635 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
U127165E01
1.603,0.639 1.899,0.795 0.295,0.156 10 F16 0.066,0.052 0.361,0.209 0.295,0.156 10 *a 1.932,2.695 2.352,2.851 0.420,0.156 10 CANH 0.234,2.619 0.653,2.776 0.420,0.156 10 CANL 1.065,2.215 0.746,2.706 false 1.857,2.783 1.366,1.802 false

Disconnect the F16 airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F16-13 (CANH) - F16-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U127166E01
1.603,0.639 1.899,0.795 0.295,0.156 10 F16 0.066,0.052 0.361,0.209 0.295,0.156 10 *a 0.241,2.619 0.661,2.776 0.420,0.156 10 IG2 0.888,2.215 0.569,2.706 false 1.025,2.619 1.445,2.776 0.420,0.156 10 E1 1.598,2.215 1.279,2.706 false 2.281,2.619 2.701,2.776 0.420,0.156 10 E2 1.901,2.215 2.22,2.706 false

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-25 (E1) - Body ground Always Below 1 Ω
F16-26 (E2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)