Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248287 CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)  Yaw Rate Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Yaw Rate Sensor Communication Stop Mode Either condition is met:
·

"Yaw Rate / Deceleration Sensor" is not displayed on "Bus Check".

·

"Yaw Rate Sensor Communication Stop Mode" in "DTC combination table" applies.


·

Power source or inside yaw rate sensor

·

Yaw rate sensor branch wire or connector

·

Yaw rate sensor



WIRING DIAGRAM

E231187E11
1.448,1.052 1.875,1.219 0.427,0.167 10 false CANH 1.448,1.5 1.875,1.667 0.427,0.167 10 false CANL 0.563,1.99 0.969,2.156 0.406,0.167 10 false F83 5.281,1.052 5.708,1.219 0.427,0.167 10 false CANH 5.281,1.49 5.708,1.656 0.427,0.167 10 false CANL 1.938,2.781 3.313,3.094 1.375,0.313 10 false from IG1 NO. 1 Relay 3.573,2.99 4.49,3.177 0.917,0.188 10 false ECU-IG NO. 1 5.281,3.25 5.708,3.417 0.427,0.167 10 false GND 1.948,1.396 2.125,1.563 0.177,0.167 10 false 20 1.969,0.958 2.146,1.125 0.177,0.167 10 false 9 5.281,2.792 5.708,2.958 0.427,0.167 10 false IG 5.042,0.969 5.354,1.135 0.313,0.167 10 false 3 5.042,1.406 5.354,1.573 0.313,0.167 10 false 2 5.042,2.698 5.333,2.865 0.292,0.167 10 false 4 5.031,3.146 5.354,3.313 0.323,0.167 10 false 1 5.146,3.896 5.573,4.063 0.427,0.167 10 false F122 0.563,2.167 2.177,2.49 1.615,0.323 10 false No. 2 Junction Connector 5.156,4.073 6.26,4.427 1.104,0.354 10 false Yaw Rate Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (YAW RATE SENSOR BRANCH WIRE)
a.

Disconnect the F122 yaw rate sensor connector.


U158552E02
1.458,1.167 1.156,1.719 true 1.667,1.167 1.979,1.719 true 0.938,1.74 1.333,1.896 0.396,0.156 10 false CANL 1.813,1.74 2.24,1.896 0.427,0.156 10 false CANH 0.448,1.052 0.813,1.229 0.365,0.177 10 false F122 0.094,0.073 0.26,0.229 0.167,0.156 10 false *a

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F122-3 (CANH) - F122-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U158553E02
1.354,1.167 1.042,1.719 true 1.781,1.177 2.25,1.729 true 0.844,1.74 1.177,1.896 0.333,0.156 10 false GND 2.177,1.74 2.354,1.896 0.177,0.156 10 false IG 0.427,1.063 0.781,1.24 0.354,0.177 10 false F122 0.104,0.083 0.271,0.24 0.167,0.156 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F122-4 (IG) - Body ground Ignition switch ON 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F122-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)