BUS CHECK (COMMUNICATION MALFUNCTION ECU)
Only CAN communication system DTCs for each ECU can be output to the intelligent tester.
Select "Bus Check" from the "System Select" screen on the intelligent tester.
Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".
Select the system of the DTC to be checked and select "Details".
CAN communication system DTCs are output.
BUS CHECK (COMMUNICATION BUS CHECK)
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.
Select "Communication Bus Check" from the "Bus Check" screen.
The screen displays the ECUs and sensors that are properly connected to the CAN communication system.
If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).
The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop-down list. The drop-down list displays "ALL", "V Bus" and the names of the remaining buses.
| Combo Box | Display Content |
|---|---|
| ALL | All ECUs (sensors) connected to the CAN bus |
| V Bus | ECUs (sensors) connected to the V Bus |
| Bus Name | ECUs (sensors) connected to the selected bus |
The connection status (shown below) is indicated by the background color displayed behind the system name.
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Not displayed | Has never been detected |
| Background Color | Connection Status |
|---|---|
| White | Detected normally |
| Yellow | Could not be detected in the past, but is currently detected |
| Red | Detected in the past, but cannot be detected now |
| Red | Has never been detected but has connection history |
| Not displayed | Has never been detected and has no connection history |
"There is no system connected the communication bus." is displayed if there are no ECUs or sensors connected to the CAN bus.
CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.
| ECU/Sensor Name | Tester Display | Installed on |
|---|---|---|
| Air conditioning amplifier assembly | Air Conditioning Amplifier | All vehicles |
| Airbag sensor assembly | Airbag | All vehicles |
| Combination meter assembly | Combination Meter | All vehicles |
| ECM | ECM (Engine) | All vehicles |
| Main body ECU (multiplex network body ECU) | Main Body | All vehicles |
| Power steering ECU assembly | Power Steering (EPS) | All vehicles |
| Skid control ECU (brake actuator assembly) | Skid Control (ABS/VSC/TRAC) | All vehicles |
| Steering angle sensor (spiral cable sub-assembly) | Spiral cable (Steering Angle Sensor) | All vehicles |
| Yaw rate sensor | Yaw Rate / Deceleration Sensor | All vehicles |
DTC TABLE BY ECU
In the CAN communication system, CAN communication system DTCs stored by the ECU can be output from the ECU by using the intelligent tester.
If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting".
ECM
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0129 | Lost Communication with Brake System Control Module |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0100 | Lost Communication With ECM/PCM "A" |
| U0101 | Lost Communication with TCM |
| U0151 | Lost Communication With Restraints Control Module |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module |
| U0164 | Lost Communication With HVAC Control Module |
SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0073 | Control Module Communication Bus Off |
| U0100 | Lost Communication With ECM/PCM "A" |
| U0123 | Lost Communication with Yaw Rate Sensor Module |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
| U0142 | Lost Communication with Body Control Module "B" |
POWER STEERING ECU ASSEMBLY
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0100 | Lost Communication with ECM/PCM "A" |
| U0129 | Lost Communication With Brake System Control Module |
COMBINATION METER ASSEMBLY
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0100 | Lost Communication with ECM/PCM "A" |
| U0129 | Lost Communication with Brake System Control Module |
| U0131 | Lost Communication with Power Steering Control Module |
| U0151 | Lost Communication with Restraints Control Module |
AIR CONDITIONING AMPLIFIER ASSEMBLY
DTC communication uses the CAN communication system.
| DTC No. | Detection Item |
|---|---|
| U0100 | Lost Communication With ECM/PCM "A" |
| U0131 | Lost Communication With Power Steering Control Module |
| U0142 | Lost Communication With Body Control Module "B" |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module |
STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)
The steering angle sensor (spiral cable sub-assembly) is connected to the CAN communication system but CAN communication DTCs are not stored.
YAW RATE SENSOR
The yaw rate sensor is connected to the CAN communication system but CAN communication DTCs are not stored.
AIRBAG SENSOR ASSEMBLY
The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not stored.
DTC COMBINATION TABLE
| Output from | Output DTC | Detected Communication Stop Mode | |||
|---|---|---|---|---|---|
| V Bus | |||||
| ECM Communication Stop Mode | Center Airbag Sensor Communication Stop Mode | ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode | Yaw Rate Sensor Communication Stop Mode | ||
| ECM | U0129 | ○*1 | - | ○ | - |
| Skid control ECU (brake actuator assembly) | U0073 | X | X | ○*1 | X |
| U0100 | ○ | X | ○*1 | X | |
| U0123 | X | ○ | ○*1 | ○ | |
| U0124 | X | ○ | ○*1 | ○ | |
| U0126 | X | X | ○*1 | X | |
| U0142 | X | X | ○*1 | X | |
| Air conditioning amplifier assembly | U0100 | ○ | - | - | - |
| U0131 | - | - | - | - | |
| U0142 | - | - | - | - | |
| U0155 | - | - | - | - | |
| Main body ECU (multiplex network body ECU) | U0100 | ○ | - | - | - |
| U0101 | ○ | - | - | - | |
| U0151 | - | ○ | - | - | |
| U0155 | - | - | - | - | |
| U0164 | - | - | - | - | |
| Power steering ECU assembly | U0100 | ○ | - | - | - |
| U0129 | - | - | ○ | - | |
| Combination meter assembly | U0100 | ○ | - | - | - |
| U0129 | - | - | ○ | - | |
| U0131 | - | - | - | - | |
| U0151 | - | ○ | - | - | |
○: Stored.
X: When one side of the branch wire is open, storage may occur.
-: Not stored.
*1: During a communication stop, cannot be stored.
| Output from | Output DTC | Detected Communication Stop Mode | ||
|---|---|---|---|---|
| V Bus | ||||
| Air Conditioning Amplifier Communication Stop Mode | Audio Receiver Assembly Communication Stop Mode | Main Body ECU Communication Stop Mode | ||
| ECM | U0129 | - | - | - |
| Skid control ECU (brake actuator assembly) | U0073 | X | X | X |
| U0100 | X | X | X | |
| U0123 | X | X | X | |
| U0124 | X | X | X | |
| U0126 | X | X | X | |
| U0142 | X | X | ○ | |
| Air conditioning amplifier assembly | U0100 | ○*1 | - | - |
| U0131 | ○*1 | - | - | |
| U0142 | ○*1 | - | ○ | |
| U0155 | ○*1 | - | - | |
| Main body ECU (multiplex network body ECU) | U0100 | - | - | ○*1 |
| U0101 | - | - | ○*1 | |
| U0151 | - | - | ○*1 | |
| U0155 | - | - | ○*1 | |
| U0164 | ○ | - | ○*1 | |
| Power steering ECU assembly | U0100 | - | - | - |
| U0129 | - | - | - | |
| Combination meter assembly | U0100 | - | - | - |
| U0129 | - | - | - | |
| U0131 | - | - | - | |
| U0151 | - | - | - | |
○: Stored.
X: When one side of the branch wire is open, storage may occur.
-: Not stored.
*1: During a communication stop, cannot be stored.
| Output from | Output DTC | Detected Communication Stop Mode | ||
|---|---|---|---|---|
| V Bus | ||||
| Power Steering ECU Communication Stop Mode | Steering Angle Sensor Communication Stop Mode | Combination Meter ECU Communication Stop Mode | ||
| ECM | U0129 | - | - | - |
| Skid control ECU (brake actuator assembly) | U0073 | X | X | X |
| U0100 | X | X | X | |
| U0123 | X | X | X | |
| U0124 | X | X | X | |
| U0126 | X | ○ | X | |
| U0142 | X | X | X | |
| Air conditioning amplifier assembly | U0100 | - | - | - |
| U0131 | ○ | - | - | |
| U0142 | - | - | - | |
| U0155 | - | - | ○ | |
| Main body ECU (multiplex network body ECU) | U0100 | - | - | - |
| U0101 | - | - | - | |
| U0151 | - | - | - | |
| U0155 | - | - | ○ | |
| U0164 | - | - | - | |
| Power steering ECU assembly | U0100 | ○*1 | - | - |
| U0129 | ○*1 | - | - | |
| Combination meter assembly | U0100 | - | - | ○*1 |
| U0129 | - | - | ○*1 | |
| U0131 | ○ | - | ○*1 | |
| U0151 | - | - | ○*1 | |
○: Stored.
X: When one side of the branch wire is open, storage may occur.
-: Not stored.
*1: During a communication stop, cannot be stored.