Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248287 CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on "Bus Check".

·

"Power Steering ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

E236738E02
4.99,0.813 5.198,0.979 0.208,0.167 10 false 7 5.281,1.031 5.76,1.229 0.479,0.198 10 false CANH 5.281,1.5 5.708,1.667 0.427,0.167 10 false CANL 1.969,2.542 3.344,2.854 1.375,0.313 10 false from IG1 NO. 1 Relay 3.531,2.74 4.427,2.906 0.896,0.167 10 false ECU-IG NO.1 5.281,3.25 5.708,3.417 0.427,0.167 10 false PGND 4.99,1.313 5.198,1.479 0.208,0.167 10 false 8 1.969,0.958 2.24,1.125 0.271,0.167 10 false 6 1.948,1.396 2.26,1.563 0.313,0.167 10 false 17 5.281,2.552 5.708,2.719 0.427,0.167 10 false IG 4.99,2.344 5.198,2.51 0.208,0.167 10 false 1 4.99,3.042 5.198,3.208 0.208,0.167 10 false 2 0.51,2.229 2.125,2.552 1.615,0.323 10 false No. 2 Junction Connector 4.948,1.042 5.333,1.208 0.385,0.167 10 false F6 4.948,1.5 5.333,1.667 0.385,0.167 10 false F6 0.521,2.031 0.823,2.198 0.302,0.167 10 false F83 4.948,2.552 5.333,2.719 0.385,0.167 10 false F6 2.375,2.104 3.323,2.417 0.948,0.313 10 false from ALT Fuse 3.802,2.281 4.104,2.448 0.302,0.167 10 false EPS 5.281,2.094 5.708,2.26 0.427,0.167 10 false PIG 4.99,1.885 5.198,2.052 0.208,0.167 10 false 1 4.927,2.094 5.313,2.26 0.385,0.167 10 false A42 4.917,3.24 5.302,3.406 0.385,0.167 10 false A42 4.688,3.979 6.698,4.625 2.01,0.646 10 false Power Steering ECU Assembly 1.448,1.052 1.865,1.24 0.417,0.188 10 false CANH 1.448,1.51 1.885,1.698 0.438,0.188 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
a.
U127246E01
1.618,0.065 1.914,0.221 0.295,0.156 10 F6 0.103,0.065 0.398,0.221 0.295,0.156 10 *a 2.073,1.509 2.493,1.665 0.420,0.156 10 CANH 0.686,1.509 1.105,1.665 0.420,0.156 10 CANL 1.701,1.096 2.02,1.587 false 1.517,1.096 1.198,1.587 false

Disconnect the F6 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U127278E01
1.617,0.241 1.912,0.397 0.295,0.156 10 F6 1.565,2.707 1.860,2.863 0.295,0.156 10 A42 0.113,0.068 0.408,0.225 0.295,0.156 10 *a 2.302,0.591 2.722,0.747 0.420,0.156 10 IG 1.929,1.159 2.247,0.668 false 0.585,3.933 1.005,4.089 0.420,0.156 10 PGND 2.383,3.933 2.802,4.089 0.420,0.156 10 PIG 1.133,4.017 1.452,3.526 false 2.323,4.017 2.004,3.526 false

a.

Disconnect the A42 power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-1 (PIG) - Body ground Always 11 to 14 V
F6-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-2 (PGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)