Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248288 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal / OFF or ON OFF: No key is in ignition key cylinder
ON: Key is in ignition key cylinder
-
ACC SW Ignition switch status / OFF or ON OFF: Ignition switch off
ON: Ignition switch on (ACC)
-
IG SW Ignition switch status / OFF or ON OFF: Ignition switch off
ON: Ignition switch to ON
-
RR Door Courtesy SW*1 Rear door courtesy light switch LH and RH signal / OFF or ON OFF: Rear door LH and RH closed
ON: Rear door LH or RH opened
-
RL Door Courtesy SW*1 Rear door courtesy light switch LH and RH signal / OFF or ON OFF: Rear door LH and RH closed
ON: Rear door LH or RH opened
-
Back Door Courtesy SW Back door courtesy switch signal / OFF or ON OFF: Back door closed
ON: Back door opened
-
Back Door Open Back door open status / Prohibit or Permit Prohibit: Back door locked
Permit: Back door unlocked
-
Door Lock SW-Lock Door manual lock switch signal / OFF or ON OFF: Door control switch (for front driver door side) is turned to unlock position
ON: Door control switch (for front driver door side) is turned to lock position
-
Door Lock SW-Unlock Door manual unlock switch signal / OFF or ON OFF: Door control switch (for front driver door side) is turned to lock position
ON: Door control switch (for front driver door side) is turned to unlock position
-
Door Key SW-Lock Door key lock and unlock switch signal/ OFF or ON OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to lock position
-
Door Key SW-Unlock Door key lock and unlock switch signal/ OFF or ON OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to unlock position
-
FR Door Lock Pos*3 Front door unlock detection switch RH signal / LOCK or UNLOCK LOCK: Front RH locked
UNLOCK: Front RH door unlocked
-
FR Door Courtesy Front RH door courtesy light switch signal / ON or OFF ON: Front RH door closed
OFF: Front RH door opened
-
FL Door Lock Pos*2 Front door unlock detection switch LH signal / LOCK or UNLOCK LOCK: Front LH side door locked
UNLOCK: Front LH side door unlocked
-
FL Door Courtesy Front LH door courtesy light switch signal / ON or OFF ON: Front LH door closed
OFF: Front LH door opened
-
Back Door Open Handle SW Back door opener switch signal / OFF or ON OFF: Back door opener switch not pushed
ON: Back door opener switch pushed
-
RR-Door Lock Pos SW*1 Not available / OFF or ON - -
RL-Door Lock Pos SW*1 Not available / OFF or ON - -

*1: for 5 Door

*2: for LHD

*3: for RHD




ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Door Lock Door lock motor OFF / Unlock / Lock -
Trunk and Back-Door Open Back door lock motor OFF / ON -