Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY AMPLIFIER


U158146E02
3.438,0.271 3.729,0.427 0.292,0.156 10 false F55

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F55-7 (AGND) - Body ground - GR - Body ground Ground Always Below 1 Ω -
F55-1 (VC5) - F55-7 (AGND) Input P - GR Transponder key amplifier power supply No key in ignition key cylinder Below 1 V -
F55-4 (CODE) - F55-7 (AGND) Output G - GR Demodulated signal of key code data No key in ignition key cylinder Below 1 V -
F55-5 (TXCT) - F55-7 (AGND) Input L - GR Key code output signal No key in ignition key cylinder Below 1 V -


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F55-1 (VC5) - F55-7 (AGND) Input P - GR Transponder key amplifier power supply Key inserted in ignition key cylinder Pulse generation (See waveform 1)
·

Bcc Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number


(If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above)
F55-4 (CODE) - F55-7 (AGND) Output G - GR Demodulated signal of key code data Key inserted in ignition key cylinder Pulse generation (See waveform 2)
F55-5 (TXCT) - F55-7 (AGND) Input L - GR Key code output signal Key inserted in ignition key cylinder Pulse generation (See waveform 3)


c.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B287844E06
0.208,1.25 0.573,1.396 0.365,0.146 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F55-1 (VC5) - F55-7 (AGND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B287845E06
0.208,1.24 0.531,1.396 0.323,0.156 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F55-4 (CODE) - F55-7 (AGND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.
B287846E08
0.219,1.24 0.552,1.427 0.333,0.188 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F55-5 (TXCT) - F55-7 (AGND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder




CHECK TRANSPONDER KEY ECU ASSEMBLY


U158150E02
3.365,0.615 3.656,0.771 0.292,0.156 10 false F54

a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F54-16 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω -
F54-1 (+B) - F54-16 (GND) Input Y - BR Battery Always 11 to 14 V +B
F54-2 (IG) - F54-16 (GND) Input V - BR Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
F54-3 (KSW) - F54-16 (GND) Input BE - BR Unlock warning switch No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key inserted in ignition key cylinder Below 1 Ω


c.

Reconnect the F54 transponder key ECU assembly connector.


d.

Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F54-14 (VC5) - F54-16 (GND) Input P - BR Transponder key amplifier power supply No key in ignition key cylinder Below 1 V
·

Bcc Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number


(If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above)
Key inserted in ignition key cylinder Pulse generation (See waveform 1)
F54-4 (TXCT) - F54-16 (GND) Input L - BR Key code output signal No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 2)
F54-15 (CODE) - F54-16 (GND) Output G - BR Demodulated signal of key code data No key in ignition key cylinder Below 1 V
Key inserted in ignition key cylinder Pulse generation (See waveform 3)
F54-13 (EFIO) - F54-16 (GND) Input R - BR ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation (See waveform 4)
F54-12 (EFII) - F54-16 (GND) Output LG - BR ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation (See waveform 5) E/G Start Permission
F54-9 (D) - F54-16 (GND) Input/Output B - BR Diagnosis tester communication Always Pulse generation -
F54-5 (AGND) - Body ground - GR - Body ground Transponder key amplifier ground Always Below 1 Ω -


e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B287844E06
0.208,1.25 0.573,1.396 0.365,0.146 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F54-14 (VC5) - F54-16 (GND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B287846E08
0.219,1.24 0.552,1.427 0.333,0.188 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F54-4 (TXCT) - F54-16 (GND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.
B287845E06
0.208,1.24 0.531,1.396 0.323,0.156 10 false GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F54-15 (CODE) - F54-16 (GND)
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iv.

Waveform 4 (Reference)

B288668E18
2.719,1.313 2.906,1.49 0.188,0.177 10 false *c 3.323,1.313 3.51,1.49 0.188,0.177 10 false *d 0.917,1.198 1.25,1.375 0.333,0.177 10 false GND 2.708,3.094 2.896,3.271 0.188,0.177 10 false *e 2.344,3.094 2.531,3.271 0.188,0.177 10 false *c 0.917,2.979 1.25,3.156 0.333,0.177 10 false GND 0.781,0.042 0.969,0.219 0.188,0.177 10 false *a 0.781,1.875 0.969,2.052 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection F54-13 (EFIO) - F54-16 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


v.

Waveform 5 (Reference)

B288667E19
1.521,1.313 1.708,1.49 0.188,0.177 10 false *c 2.094,1.292 2.281,1.469 0.188,0.177 10 false *d 0.906,1.198 1.24,1.375 0.333,0.177 10 false GND 1.885,3.083 2.073,3.26 0.188,0.177 10 false *e 1.51,3.083 1.698,3.26 0.188,0.177 10 false *c 0.917,2.969 1.25,3.146 0.333,0.177 10 false GND 0.708,0.073 0.896,0.25 0.188,0.177 10 false *a 0.708,1.854 0.896,2.031 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection F54-12 (EFII) - F54-16 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected




CHECK ECM


U158096E02
5.51,0.25 5.781,0.406 0.271,0.156 10 false A74 2.26,0.25 2.531,0.406 0.271,0.156 10 false B84

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
B84-104 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A74-20 (BATT) - B84-104 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
A74-1 (+B2) - B84-104 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
A74-2 (+B) - B84-104 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
A74-10 (IMO) - B84-104 (E1) Input W - W-B Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. Pulse generation
(See waveform 1)
-
A74-11 (IMI) - B84-104 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

B288667E19
1.521,1.313 1.708,1.49 0.188,0.177 10 false *c 2.094,1.292 2.281,1.469 0.188,0.177 10 false *d 0.906,1.198 1.24,1.375 0.333,0.177 10 false GND 1.885,3.083 2.073,3.26 0.188,0.177 10 false *e 1.51,3.083 1.698,3.26 0.188,0.177 10 false *c 0.917,2.969 1.25,3.146 0.333,0.177 10 false GND 0.708,0.073 0.896,0.25 0.188,0.177 10 false *a 0.708,1.854 0.896,2.031 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection A74-10 (IMO) - B84-104 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


ii.

Waveform 2 (Reference)

B288668E18
2.719,1.313 2.906,1.49 0.188,0.177 10 false *c 3.323,1.313 3.51,1.49 0.188,0.177 10 false *d 0.917,1.198 1.25,1.375 0.333,0.177 10 false GND 2.708,3.094 2.896,3.271 0.188,0.177 10 false *e 2.344,3.094 2.531,3.271 0.188,0.177 10 false *c 0.917,2.979 1.25,3.156 0.333,0.177 10 false GND 0.781,0.042 0.969,0.219 0.188,0.177 10 false *a 0.781,1.875 0.969,2.052 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection A74-11 (IMI) - B84-104 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected