Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2014.07–2016.09
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


U158150E02
3.365,0.615 3.656,0.771 0.292,0.156 10 false F54

a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F54-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω -
F54-1 (+B) - F54-5 (GND) Input Y - BR Battery Always 11 to 14 V +B
F54-2 (IG) - F54-5 (GND) Input V - BR Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
F54-3 (KSW) - F54-5 (GND) Input BE - BR Unlock warning switch No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key inserted in ignition key cylinder Below 1 Ω


c.

Reconnect the F54 transponder key ECU assembly connector.


d.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F54-9 (D) - F54-5 (GND) Input/Output B - BR DLC3 communication Without communication Below 1 V -
During communication Pulse generation
F54-4 (ANT1) - F54-5 (GND) Input/Output L - BR Transponder key coil power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
F54-15 (ANT2) - F54-5 (GND) Input/Output P - BR Transponder key coil communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
F54-13 (EFIO) - F54-5 (GND) Input R - BR ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
F54-12 (EFII) - F54-5 (GND) Output LG - BR ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)
E/G Start Permission

If the result is not as specified, the transponder key ECU assembly may be malfunctioning.


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909E04
5.771,0.833 6.229,1.031 0.458,0.198 10 false GND

Measurement Condition
Item Content
Tester Connection F54-4 (ANT1) - F54-5 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910E03
5.786,0.808 6.234,0.981 0.448,0.173 10 GND

Measurement Condition
Item Content
Tester Connection F54-15 (ANT2) - F54-5 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B288668E18
2.719,1.313 2.906,1.49 0.188,0.177 10 false *c 3.323,1.313 3.51,1.49 0.188,0.177 10 false *d 0.917,1.198 1.25,1.375 0.333,0.177 10 false GND 2.708,3.094 2.896,3.271 0.188,0.177 10 false *e 2.344,3.094 2.531,3.271 0.188,0.177 10 false *c 0.917,2.979 1.25,3.156 0.333,0.177 10 false GND 0.781,0.042 0.969,0.219 0.188,0.177 10 false *a 0.781,1.875 0.969,2.052 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection F54-13 (EFIO) - F54-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B288667E19
1.521,1.313 1.708,1.49 0.188,0.177 10 false *c 2.094,1.292 2.281,1.469 0.188,0.177 10 false *d 0.906,1.198 1.24,1.375 0.333,0.177 10 false GND 1.885,3.083 2.073,3.26 0.188,0.177 10 false *e 1.51,3.083 1.698,3.26 0.188,0.177 10 false *c 0.917,2.969 1.25,3.146 0.333,0.177 10 false GND 0.708,0.073 0.896,0.25 0.188,0.177 10 false *a 0.708,1.854 0.896,2.031 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection F54-12 (EFII) - F54-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM


U158096E03
5.51,0.25 5.781,0.406 0.271,0.156 10 false A74 2.26,0.25 2.531,0.406 0.271,0.156 10 false B84

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
B84-104 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A74-20 (BATT) - B84-104 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
A74-1 (+B2) - B84-104 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
A74-2 (+B) - B84-104 (E1) Input B - W-B +B power supply Ignition switch ON 11 to 14 V -
A74-10 (IMO) - B84-104 (E1) Input W - W-B Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication input Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. Pulse generation
(See waveform 1)
-
A74-11 (IMI) - B84-104 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Transponder key ECU assembly communication output Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Inspect using an oscilloscope.

i.

Waveform 1 (Reference)

B288667E19
1.521,1.313 1.708,1.49 0.188,0.177 10 false *c 2.094,1.292 2.281,1.469 0.188,0.177 10 false *d 0.906,1.198 1.24,1.375 0.333,0.177 10 false GND 1.885,3.083 2.073,3.26 0.188,0.177 10 false *e 1.51,3.083 1.698,3.26 0.188,0.177 10 false *c 0.917,2.969 1.25,3.146 0.333,0.177 10 false GND 0.708,0.073 0.896,0.25 0.188,0.177 10 false *a 0.708,1.854 0.896,2.031 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection A74-10 (IMO) - B84-104 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


ii.

Waveform 2 (Reference)

B288668E18
2.719,1.313 2.906,1.49 0.188,0.177 10 false *c 3.323,1.313 3.51,1.49 0.188,0.177 10 false *d 0.917,1.198 1.25,1.375 0.333,0.177 10 false GND 2.708,3.094 2.896,3.271 0.188,0.177 10 false *e 2.344,3.094 2.531,3.271 0.188,0.177 10 false *c 0.917,2.979 1.25,3.156 0.333,0.177 10 false GND 0.781,0.042 0.969,0.219 0.188,0.177 10 false *a 0.781,1.875 0.969,2.052 0.188,0.177 10 false *b

Text in Illustration
*a Waveform A *b Waveform B
*c Approximately 160 ms *d Approximately 510 ms
*e Approximately 270 ms - -

Measurement Condition
Item Content
Tester Connection A74-11 (IMI) - B84-104 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected