Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2796  No Communication in Immobiliser System  


DESCRIPTION

DTC B2796 is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2796 The key code cannot be transmitted (1 trip detection logic*).
·

Key

·

Harness or connector

·

Transponder key ECU assembly

·

Transponder key amplifier


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2796 Response

WIRING DIAGRAM

B193467E19
5.333,2.615 6.792,2.927 1.458,0.313 10 false Transponder Key ECU Assembly 5.333,2.438 5.625,2.615 0.292,0.177 10 false F54 1.031,2.979 1.323,3.156 0.292,0.177 10 false F55 1.031,3.167 2.719,3.344 1.688,0.177 10 false Transponder Key Amplifier 1.875,2.49 2.49,2.667 0.615,0.177 10 false Amplifier 5.438,0.76 5.646,0.927 0.208,0.167 10 false 14 3.229,0.75 3.354,0.917 0.125,0.167 10 false 1 5.438,1.167 5.646,1.333 0.208,0.167 10 false 15 3.229,1.156 3.354,1.323 0.125,0.167 10 false 4 5.521,1.563 5.646,1.729 0.125,0.167 10 false 4 3.229,1.552 3.354,1.719 0.125,0.167 10 false 5 5.521,1.958 5.646,2.125 0.125,0.167 10 false 5 3.229,1.948 3.354,2.115 0.125,0.167 10 false 7 5.677,2.031 6.135,2.198 0.458,0.167 10 false AGND 5.677,1.656 6.094,1.823 0.417,0.167 10 false TXCT 5.677,1.26 6.135,1.427 0.458,0.167 10 false CODE 5.677,0.854 6.01,1.021 0.333,0.167 10 false VC5 2.74,1.948 3.198,2.115 0.458,0.167 10 false AGND 2.802,1.552 3.219,1.719 0.417,0.167 10 false TXCT 2.729,1.156 3.188,1.323 0.458,0.167 10 false CODE 1.417,0.969 1.844,1.135 0.427,0.167 10 false ANT1 1.417,2.167 1.844,2.333 0.427,0.167 10 false ANT2 0.896,1.448 1.219,1.615 0.323,0.167 10 false Coil 2.844,0.76 3.177,0.927 0.333,0.167 10 false VC5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly or key, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTC each time (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:
·

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

·

If DTC B2796 is stored, check for DTCs with the next key after clearing the DTCs.



OK:

DTC B2796 is not output.


Result
Result Proceed to
OK A
NG (all keys) B
NG (any key) C



A

B

3.CHECK CONNECTION OF CONNECTOR

C

REPLACE KEY THAT CANNOT START ENGINE

3.CHECK CONNECTION OF CONNECTOR
a.

Check the connection of the transponder key ECU assembly and transponder key amplifier connectors.


b.

Visually inspect the terminals of the transponder key ECU assembly and transponder key amplifier connectors.

OK:

Connectors are properly connected.




OK

4.CHECK WHETHER ENGINE STARTS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

5.CLEAR DTC

NG

7.CHECK TRANSPONDER KEY AMPLIFIER
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2796 is not output.




OK

END (CONNECTOR WAS NOT PROPERLY CONNECTED)

NG

7.CHECK TRANSPONDER KEY AMPLIFIER
7.CHECK TRANSPONDER KEY AMPLIFIER
a.

Using an oscilloscope, check the waveform.

B445193E01
1.146,1.948 1.531,1.188 false 1.656,1.927 1.792,1.188 false 2.177,1.938 1.927,1.198 false 2.625,1.906 2.313,1.198 false 0.333,0.365 0.646,0.563 0.313,0.198 10 false *a 0.375,2.604 0.688,2.802 0.313,0.198 10 false *b 3.823,0.448 4.135,0.646 0.313,0.198 10 false *c 3.948,2.615 4.26,2.813 0.313,0.198 10 false *d 4.104,1.573 4.438,1.771 0.333,0.198 10 false GND 4.104,3.74 4.438,3.938 0.333,0.198 10 false GND 0.604,3.771 0.938,3.969 0.333,0.198 10 false GND 0.948,1.969 1.385,2.156 0.438,0.188 10 false AGND 1.51,1.958 1.948,2.146 0.438,0.188 10 false TXCT 1.979,1.948 2.417,2.135 0.438,0.188 10 false CODE 2.51,1.927 2.948,2.115 0.438,0.188 10 false VC5

i.

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F55-1 (VC5) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F55-5 (TXCT) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F55-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Component with harness connected
(Transponder Key Amplifier)
*b Waveform 1
*c Waveform 2
*d Waveform 3

Result
Result Proceed to
OK A
NG (Waveform 1) B
NG (Waveform 2) C
NG (Waveform 3) D




A

REPLACE TRANSPONDER KEY ECU ASSEMBLY

B

8.CHECK TRANSPONDER KEY AMPLIFIER (VC5)

C

10.CHECK TRANSPONDER KEY AMPLIFIER (TXCT)

D

12.CHECK TRANSPONDER KEY AMPLIFIER (CODE)
8.CHECK TRANSPONDER KEY AMPLIFIER (VC5)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158188E02
1.156,1.26 1.156,1.906 false 0.177,2.156 0.417,2.385 0.24,0.229 10 false *b 0.177,0.125 0.417,0.354 0.24,0.229 10 false *a 0.146,3.552 0.479,3.729 0.333,0.177 10 false GND 1.656,0.323 1.917,0.5 0.26,0.177 10 false F55 1.021,1.938 1.323,2.104 0.302,0.167 10 false VC5

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection F55-1 (VC5) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

NG

9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-1 (VC5) - F54-14 (VC5) Always Below 1 Ω
F55-7 (AGND) - F54-5 (AGND) Always Below 1 Ω
F55-1 (VC5) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TRANSPONDER KEY AMPLIFIER (TXCT)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158193E02
1.948,1.26 1.948,1.969 false 1.667,0.323 1.927,0.5 0.26,0.177 10 false F55 1.813,1.99 2.229,2.167 0.417,0.177 10 false TXCT 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.177 0.344,2.333 0.167,0.156 10 false *b 0.156,3.521 0.51,3.698 0.354,0.177 10 false GND

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection F55-5 (TXCT) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

NG

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-5 (TXCT) - F54-4 (TXCT) Always Below 1 Ω
F55-5 (TXCT) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TRANSPONDER KEY AMPLIFIER (CODE)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158190E02
1.75,1.25 1.75,1.948 false 1.656,0.302 1.917,0.479 0.26,0.177 10 false F55 0.125,3.521 0.479,3.698 0.354,0.177 10 false GND 0.219,0.156 0.385,0.313 0.167,0.156 10 false *a 0.24,2.188 0.406,2.344 0.167,0.156 10 false *b 1.583,1.969 2.01,2.146 0.427,0.177 10 false CODE

Using an oscilloscope, check the waveform.

i.

Waveform (Reference)

Measurement Condition
Item Content
Tester Connection F55-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

NG

13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-4 (CODE) - F54-15 (CODE) Always Below 1 Ω
F55-4 (CODE) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR